Bosch VSS7902/00T Quick start guide

VSS7902/00T - VS79015T
VSS7905/00T - VS79055T
Installation and Operational Manual
Alarm/Action Box
EN
Manuel d installation et d opération
Module Alarme/Intervention
FR
Installations- und Bedieningsanleitung
Alarm/Aktion Box
DE
Installatie- en bedieningshandleiding
Alarm/Actie Module
NL
Manuale de installazione ed uso
Scatola Allarme/Action
IT
Manual de instalação e de instruções
Caixa de Alarme/Acção
PT
Manual de instalación y uso
Caja de Alarma/Acción
ES
Installations- og betjeningsvejledning
Alarm/Handlingskasse
DA
Installations- och bruksanvisning
Larm-/Åtgärdsenhet
SV
Asennus- ja käyttöohje
Hälytys-/Toiminolaitteella
SU
Installasjons- og bruksanvisning
Alarm/Handlingsboks
NO
Installation and Operational Manual
Alarm/Action Box
GR

Bosch Security Systems | 2004-06
7902 - 7905 | Installation and Operational Manual
TABLE OF CONTENTS
ENGLISH ................................................................ 1
FRANÇAIS ............................................................. 15
DEUTSCH .............................................................. 30
ESPAGÑOL ............................................................ 43
NEDERLANDS ...................................................... 58
ITALIANO .............................................................. 71
PORTUGUÊS ......................................................... 85
DANSK .................................................................... 98
SVENSKA ............................................................... 111
SUOMI .................................................................... 124
NORSK .................................................................... 136
GREEK .................................................................... 149
TECHNICAL SPECIFICATIONS ...................... 163

Bosch Security Systems | 2004-06
EN | 1
7902 - 7905 | Installation and Operational Manual
FCC DECLARATION
Installation and Operational ManualENGLISHEN
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Increase the distance between the equipment and the receiver.
• Connect the equipment to a power socket on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.

Bosch Security Systems | 2004-06
EN | 2
7902 - 7905 | Installation and Operational Manual
ELECTRO MAGNETIC COMPATIBILITY (EMC)
Installation and Operational Manual
This equipment complies with European rules for EMC according to
EN55013, EN55020 and EN50082-1.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
The equipment conforms with the EMC directive and low-voltage
directive.
This device complies to FCC rules under test conditions that included
use of system cables and connectors between system components. If
you have any problems, contact your dealer.
WARNINGS
Any unauthorized modification to this equipment may cause
violation of the FCC rules resulting in the revocation of the
authorization to operate the equipment.
To prevent fire or shock hazard, do not expose this accessory to rain
or moisture. Do not attempt to disassemble the camera. In order to
prevent shock and fire hazard, do not remove screws or covers.
There are no user-serviceable parts inside.
WARNING:
The exclamation mark within a triangle is intended to alert
the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.

Bosch Security Systems | 2004-06
EN | 3
7902 - 7905 | Installation and Operational Manual
Alarm/Action Box
TABLE OF CONTENTS
Introduction ...................................................................................... 4
Installation ........................................................................................ 6
Mounting the box
Installation and setting of an optional Passive Infra-Red
(PIR) detector
Location of the PIR
Installation of the PIR
PIR settings
Walk test LED
Pulse counter
System cable
Action output
Alarm input
Settings............................................................................................. 13
Tamper switch active

Bosch Security Systems | 2004-06
EN | 4
7902 - 7905 | Installation and Operational Manual
INTRODUCTION
Thank you for buying this accessory for your observation system.
1. System monitor
2. Video recorder (VCR)
3. Slave monitor
4. Accessory boxes (0-2 per cable)
5. System cameras
The following items are included in this kit:
1. Alarm/action box
1. System cable (5m/15ft)
1. User manual
1. PIR unit (for version with PIR)
1. Cable (50 cm) for interconnection between alarm/action box and
PIR (for version with PIR)
Colour Observation Monitor
4
5 5
2
talk action menu _+next
auto view
Colour Observation system
Colour Observation Monitor
4 4
4
4
4
4
4
3
1
R
A
E
N
>
<
R
A
F
R
A
E
N
>
<
R
A
F
5
R
A
E
N
>
<
R
A
F
5
R
A
E
N
>
<
R
A
F

Bosch Security Systems | 2004-06
EN | 5
7902 - 7905 | Installation and Operational Manual
The alarm/action box performs two distinct functions:
1. Action
This function, for example, opens a door remotely.
Pressing the action button of the system monitor activates a relay
contact. This contact (N.O., N.C.) can activate, for instance, a door
opener.
Note that the action button only activates the action box designated
to the camera input whose picture is shown on the monitor screen.
2. Alarm
This function provides alarm inputs to the security system. All kinds
of detectors having a N.O. or N.C. contact are supported, for
example:
• infrared detectors
• smoke detectors
• magnetic door/window contacts
When a detector triggers the alarm/action box, the system monitor
automatically switches to the camera input the alarm/action box is
designated to. The system monitor produces an alarm and activates
its alarm contact.
There are two versions of the alarm/action box: one with a Passive
InfraRed (PIR) motion detector and one without. The description in
this manual applies to both versions.
N.O.
N.C.
common
N.O. = Normally Open
N.C. = Normally Closed

Bosch Security Systems | 2004-06
EN | 6
7902 - 7905 | Installation and Operational Manual
If the automatic camera sequence is active, it stops at the camera
input in question.
INSTALLATION
Remark: When the system configuration is altered, the system
monitor needs to check and memorize the configuration of the
cameras and accessories connected to its inputs.
This is done automatically when the power is switched on. Use the
power switch to switch off. Operating the power save key is not
sufficient.
If switching off is impracticable, use the auto install option of the
system monitor's install menu.
Mounting the box
1. Loosen the screw holding the cover and remove the cover.
2. Remove the circuit board1.
3. Fasten the bottom plate of the box with two screws.
CL 66610005_501.AI

Bosch Security Systems | 2004-06
EN | 7
7902 - 7905 | Installation and Operational Manual
4. Fit the circuit board.
5. Now make the connections as described in section 'Action
output'.
Remark: See section 'Installation and setting of an optional
Passive Infra-Red (PIR) detector', for installation and
connection of an PIR-detector.
6. IMPORTANT: Adjust the settings of the circuit board switches to
configure the box according to your system. See section 'settings'.
7. Fit the cover and secure the screw holding it.
Installation and setting of an optional Passive
Infra-Red (PIR) detector
Location of the PIR
The position of the PIR determines its view.
Select a location where an eventual burglar is most likely to be
detected.
Place the sensor at a height of ± 2.2 m to accomplish the largest field
of view (see figure below).
Sensor range (lens position 0°)
4M
13.15Ft
8M
26.3Ft
14M
46Ft
2.2M
7.2Ft
110
O
Side view Top view

Bosch Security Systems | 2004-06
EN | 8
7902 - 7905 | Installation and Operational Manual
Be aware of the following before mounting the PIR:
• Avoid a location of the PIR near to radiators, heating/cooling
ducts or air conditioners.
• Do not point the sensor's field of view to windows subject to
direct sunlight or drafts.
• Do not block the sensor's field of view by placing large objects in
its line of sight (e.g. curtains, potted plants, furniture).
Installation of the PIR
1. Remove the fixation-screw (1) and open the housing by releasing
the locking latch (2). Both are located at the bottom of the unit.
2. Remove the circuit board by loosening the fixation-screw (1).
3. Knock out the desired mounting holes (1) and wiring holes (2) in
the bottom plate.
4. Thread the wires through the knocked out wiring hole(s).
5. Fasten the bottom plate with two screws, using the mounting
holes.
6. Fit the circuit board.
WARNING:
Never touch the face of the PYRO sensor (refer to lay out
drawing next page).
CL 76610006_002.AI
3
1
2
CL 76610006_003.AI
1
1 2

Bosch Security Systems | 2004-06
EN | 9
7902 - 7905 | Installation and Operational Manual
Adjust lens position (0°, -5° or -10°) according to desired maximum
sensor range (see table below).
Remark: Do not use positions +5° or +10° as they do not apply to
this PIR.
7. Make the interconnections between the PIR and the alarm/action
box with the cable supplied (see figure below).
Sensor height Maximum sensor range (m) / Lens position (°)
0° -5° -10°
2.5 m 14 m 12.5 m 11 m
2.0 m 12 m 10.5 m 9.5 m
1.5 m 10 m 8.5 m 8 m
1
2
3
4
5
6
7
8
Terminal block (for interconnection with alarm/action box)
Lens position (sensor range adjustment)
Jumper (walk test LED activated/deactivated)
Tamper switch
PYRO sensor
Jumper (1, 2 or 3 pulse count)
Locking latch
Terminal block in alarm/action box
5 87 6
2 14 3
GND
NC
+12V
+10
+5
0
-5 -10
+
_
NC
PIR

Bosch Security Systems | 2004-06
EN | 10
7902 - 7905 | Installation and Operational Manual
8. Adjust settings of walk test LED and/or pulse counter, if
required.
See section 'PIR settings'.
9. Fit the front cover. Check if it is locked to the bottom side.
10. Fasten the fixation-screw.
Remark: The PIR detector will start detecting movement
approximately 2 minutes after mains power-on.
PIR settings
There are 2 jumpers to set the PIR to your own requirements:
• Walk test LED
• Pulse counter (1, 2 or 3)
See previous figure for the location of the jumpers.
Walk test LED
• jumper installed:
Walk test LED is activated. When the PIR sensor is triggered, the
LED will light.
• jumper not installed:
Walk test LED is deactivated.
Pulse counter
Set this jumper to select the number of times the sensor must be
triggered (1, 2 or 3 times) before an alarm is generated.
The following jumper settings are possible:

Bosch Security Systems | 2004-06
EN | 11
7902 - 7905 | Installation and Operational Manual
Remark: The PIR detector is equiped with a 'detection window'. In
case of an alarm, 15 seconds after the last movement has been
detected, a new alarm can be generated.
System cable
For the interconnections between the monitor, accessories and
camera a system cable is supplied. For optimum picture and sound
quality you should always use 4-wire dual twisted-pair cable when
extending the connection (max. 300m/900ft). The cable and plugs are
available in the hobby and professional trade. Pay attention that the
connectors are fixed to the cable corresponding to the figure below.
If the cable length between monitor and camera exeeds 200m/600ft
after an accessory is inserted in the line a mains power adapter should
be used to power the camera (see accessories).
2X 3X1X
3P
2P
3P
2P
3P
2P
5
4
3
2
4-5
2-3
5
4
3
2
4-5
2-3
5
4
3
2
5
4
3
2

Bosch Security Systems | 2004-06
EN | 12
7902 - 7905 | Installation and Operational Manual
The two sockets for the system cable are interchangeable. One socket
connects the box to the system component previous in the cable, the
other to the next (if any).
Action output
The figure below shows the screw terminals to which, for example, a
door-opener circuit can be connected.
1. System-cable input
2. System-cable output
3. Switches 1, 2 & 3
CAUTION:
The plugs used for the observation system have the same
dimensions as standard telephone plugs.
Never connect the security system with telephone
equipment!
6
CL 66610005_505.AI
123
7
689
4
0
1
23
5
45
21 3
CAMERA #
1 BOX TAMPER N LAST
ON OFF
2
Y
OFF
+
_
NC
PIR

Bosch Security Systems | 2004-06
EN | 13
7902 - 7905 | Installation and Operational Manual
4. Rotary switch (designates the box to a camera input)
5. Tamper switch
6. Terminal block for optional Passive Infra-Red detector
Alarm input
The alarm/action box provides inputs for detectors with N.O. and
N.C. contacts. The figure above shows how they are connected to the
screw terminals of the box.
SETTINGS
Four switches - located inside the case, on the circuit board - are used
to configure the circuit according to the system.
• The rotary switch designates the box to a particular camera input.
• The three small slide switches have the following functions:
Restrictions:
• Maximum one Alarm/Action Box and/or Intercom Box per
camera input.
• Box always designated to camera in line.
• Camera is always last in line.
Dedicated settings for Eazeo color systems:
Note: • When no detectors with N.C. contacts are used terminals
1and 2must be interconnected with a wire.
• When no PIR detector is used terminals NC and – of
terminal block (6) must be interconnected with a wire.
Switch Off On Description
1 BOX 1 2 number of accessories
2 TAMPER TAMPER OFF tamper-switch
override
3 LAST N

Bosch Security Systems | 2004-06
EN | 14
7902 - 7905 | Installation and Operational Manual
• Switches 1, 2 & 3
•Rotaryswitch
Any position (automatically linked to camera in line)
• PIR terminal block (Alarm/Action Box only)
Link NC to - when no PIR is used.
Tamper switch active
On the circuit board a tamper switch secures the box. When opening
the box this switch triggers an alarm on the monitor. To suppress a
continuous alarm message while servicing the system, the tamper-
switch override is set in the OFF position.
CAUTION:
Don't forget to reactivate the tamper switch by switching
the override to the TAMPER position!
#1
A
ny position
#2 OFF tamper switch active, ON override tamper switch
(tamper OFF)
#3 always OFF (N last)

Bosch Security Systems | 2004-06
| 163
7902 - 7905 | Installation and Operational Manual
Technical specifications
Specifications may be changed without notice.
Alarm/Action Box
Installation and Operational ManualTechnical Specifications
Power supply through the system cable (24VDC)
Contact rating action relay 30V, 5A AC/DC
Alarm input trigger threshold > 150 Ohm (N.C. input)
< 150 Ohm (N.O. input)
System connectors RJ11E modular (‘telephone’
connectors)
System cable 4-wire dual twisted pair cable e.g.
VSS2906/00 or VSS2930/00
PIR angle of sight
• horizontal
•vertical
110º
20º
Dimensions
• without PIR 119 x 77 x 40 mm
Ambient conditions Ammonia resistant
Temperature
• operating +10ºC - +45ºC
• storage -25ºC - +70ºC
Humidity
• operating 20... 90%RH
• storage 20... 99%RH

3122 165 22851 0426
© 2004 Bosch Security Systems B.V.
Subject to change Printed in Portugal
Bosch Sicherheitssysteme GmbH
Ludwig-Bölkow-Allee
85521 Ottobrunn
Germany
www.bosch-sicherheitssysteme.de
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
www.boschsecuritysystems.com