Bosch D623 Series User manual

Security System D623/D625
User Guide
National Security Systems [phone]
http://nationalsecuritysystems.com

D623/D625 User Guide
Page 2 © 2003 Bosch Security Systems46841D
Security System
User Guide
MYALARM COMPANY IS:
CALL BEFORE TEST: ____________________________
THIS SECURITY SYSTEM IS CONNECTED TO TELEPHONE NUMBER:
____________________________________
THE SECURITY CONTROL PANEL IS CONNECTED TO THE PHONE JACK LOCATED:
____________________________________
TRANSFORMER LOCATION: _________________________________
CIRCUIT BREAKER NUMBER: _______________________________

D623/D625 User Guide
Security System
Page 3© 2003 Bosch Security Systems 46841D
User Guide
Table of Contents
About this User Guide ........................................................................................................................................................................................5
Introduction ............................................................................................................................................................................................. 5
Security System Basics .....................................................................................................................................................................................5
What is a Point? ................................................................................................................................................................................... 5
What is a Faulted Point? .................................................................................................................................................................... 5
Are All Points the Same? .................................................................................................................................................................... 6
Controlled Points .................................................................................................................................................................................. 6
24-Hour Points ...................................................................................................................................................................................... 6
All On ....................................................................................................................................................................................................... 6
Part On ................................................................................................................................................................................................... 6
Command Center Keys .......................................................................................................................................................................................7
Command Center Tones .....................................................................................................................................................................................7
Command Center LED Descriptions ............................................................................................................................................................8
Commands .............................................................................................................................................................................................. 8
System Events ....................................................................................................................................................................................... 8
Fire Alarms .............................................................................................................................................................................................. 8
Burglary Alarms ..................................................................................................................................................................................... 8
Fire Trouble Events ............................................................................................................................................................................... 8
Non-Fire Trouble Events ...................................................................................................................................................................... 8
How Your System Reports Alarms ...............................................................................................................................................................9
Check System Status ..........................................................................................................................................................................................9
Log Out of the System .......................................................................................................................................................................................9
Silence Alarms .........................................................................................................................................................................................................9
Keypad Adjust (Cmd 49) ................................................................................................................................................................................ 10
Turn the System Off .......................................................................................................................................................................................... 10
Turn the System All On (All On or Cmd 1)............................................................................................................................................. 11
Turn the System Part On (Part On or Cmd 2) ..................................................................................................................................... 12
Turn the System Part 2 On (Cmd 3) ......................................................................................................................................................... 13
Set Part 2 Points (Cmd 65) ........................................................................................................................................................................... 14
Turn the System On with No Delay ........................................................................................................................................................... 14
Turn the System On with No Exit Tone (Delay Silent)..................................................................................................................... 16
Turn the System On with Points Faulted (Force Arm) .................................................................................................................... 17
View Faulted Points ........................................................................................................................................................................................... 18
Bypass Points ....................................................................................................................................................................................................... 18
Date and Time (Cmd 45) ................................................................................................................................................................................. 19
Change Passcode (Cmd 55) ........................................................................................................................................................................ 20
Change Others’ Passcodes (Cmd 56) .................................................................................................................................................... 21
Change Others’ Passcode Authority Levels (Cmd 56) .................................................................................................................. 22
Add a Passcode (Cmd 56) ............................................................................................................................................................................ 23
Delete Passcodes (Cmd 58) ......................................................................................................................................................................... 24
Renew One-time Passcodes (Cmd 53) ................................................................................................................................................... 25
Check System Troubles (Cmd 4)............................................................................................................................................................... 26
View Alarm Memory (Cmd 40) ..................................................................................................................................................................... 27
View System Trouble (Cmd 42) .................................................................................................................................................................. 27
View Point Trouble (Cmd 48) ....................................................................................................................................................................... 28
System Test (Cmd 41) ...................................................................................................................................................................................... 28
Walk Test (Cmd 44)............................................................................................................................................................................................ 29
Reset the System (Cmd 47) .......................................................................................................................................................................... 30
Turn Watch On/Off (Cmd 61) ........................................................................................................................................................................ 30

D623/D625 User Guide
Page 4 © 2003 Bosch Security Systems46841D
Security System
User Guide
Select Watch Tone (Cmd 62) ........................................................................................................................................................................ 31
Select Watch Points (Cmd 63)..................................................................................................................................................................... 31
Extend Auto On Time (Cmd 51) ................................................................................................................................................................... 32
Change Skeds (Cmd 52) ................................................................................................................................................................................ 32
Sked All Days Feature ...................................................................................................................................................................... 32
All On Skeds ....................................................................................................................................................................................... 33
Part On Skeds .................................................................................................................................................................................... 33
Part 2 On Skeds ................................................................................................................................................................................ 34
Off Skeds ............................................................................................................................................................................................. 34
Output On Skeds .............................................................................................................................................................................. 35
Output Off Skeds .............................................................................................................................................................................. 35
Change Outputs (Cmd 54) ............................................................................................................................................................................ 36
Remote Program (Cmd 43) ........................................................................................................................................................................... 36
All Areas Off (Cmd 81)...................................................................................................................................................................................... 37
All Areas On (Cmd 80) ..................................................................................................................................................................................... 37
Move to Area (Cmd 50) ................................................................................................................................................................................... 38
Auto-Forward On Setup (Cmd 83) ........................................................................................................................................................... 38
Auto-Forward Off Setup (Cmd 84) ........................................................................................................................................................... 39
Auto-Forward On/Off (Cmd 82) ................................................................................................................................................................. 40
Remote Arming with Telephone, Area 1 .................................................................................................................................................. 40
View Log (Cmd 85) ............................................................................................................................................................................................ 41
Basic Pager Reports ......................................................................................................................................................................................... 42
Panel Event Descriptions ................................................................................................................................................................................ 43
Security System Limitations.......................................................................................................................................................................... 47
Fire Safety and Evacuation ............................................................................................................................................................................ 47
Maintenance and Service ................................................................................................................................................................................ 48
Power Failure ........................................................................................................................................................................................................ 48
How to Clean the Command Center ......................................................................................................................................................... 48
Glossary................................................................................................................................................................................................................... 49
Index .......................................................................................................................................................................................................................... 50

D623/D625 User Guide
Security System
Page 5© 2003 Bosch Security Systems 46841D
User Guide
About this User Guide
This User’s Guide shows you how to use and maintain your security system. It covers basic functions, such as turning the
system on and off.
The functions described in this guide are programmed by your security company. Some of them may not be enabled in your
system. Certain functions covered may require you to enter your personal passcode.
Introduction
Your system helps to secure life, property, and investments against fire, theft, and bodily harm. It consists of one or more
command centers, motion sensors (such as detectors or devices located on doors and windows), and sensing devices
designed to detect the presence of smoke or combustion. Each device is connected to a sophisticated control panel with a
microprocessor that processes all events registered by the system.
Control of your security system is achieved through the command center, which offers a variety of basic and advanced
features. Its function, versatility, and ease of operation make it ideal for home or office use. The command center is tailored
to meet your individual needs. Moreover, it has been designed with you, the user, in mind.
A B C
Check Change Watch
Area
On
Status
Test System Weekly
1 2
3
1 - Text display
2 - System status indicators
3 - Sounder
Security System Basics
What is a Point?
A Point is a detection device or group of devices connected to your security system. Points are identified by the area they
monitor, such as a front door, bedroom window, or hallway.
What is a Faulted Point?
When a point (such as a door or window) is closed, it is said to be normal. When the door or window is open, the point is
said to be faulted, or not normal. When you turn your system on, you usually want all of the points in your system to be
normal. However, you can turn your system on with faulted points by using the Bypass Points command.
You can see if there are any faulted points by pressing the [*] key when the system is off.

D623/D625 User Guide
Page 6 © 2003 Bosch Security Systems46841D
Security System
User Guide
Are All Points the Same?
Not all points are the same. In fact, there are two basic types of points: Controlled and 24-hour.
Controlled Points
Controlled points respond to alarm conditions depending upon whether the system is turned on or off. They are
programmed to either respond instantly to alarm conditions, or to provide a delay for you to reach the command center
and turn the system off. Various controlled points may be located throughout your house.
When you turn your system on, you have the option of turning on all controlled points (All On) or just some of the
controlled points (Part On). See All On and Part On for more information.
24-Hour Points
24-hour points are always on, even when the system is turned off. There are two types of 24-hour points: Fire and Non-Fire.
See Reset the System on page 30 for more information.
•Fire Points: Only monitor fire detection devices such as smoke detectors. They are always on and cannot be
turned off.
•Non-Fire Points: Always on and cannot be turned off.
All On
When you turn your system All On you are turning on all controlled points, both interior (motion detectors) and perimeter
(doors and windows of the building).
Controlled Points are All On
1233
43
Part On
When you turn your system Part On you are turning on only a portion of the controlled points. The particular points
included in this portion are determined by your alarm company. Part points may include only the perimeter (doors and
windows) of your system, or the points on the first floor of a two-story house. Check with your security company to learn
which points are Part points.
Controlled Points are Part On
1233
43
1 - Dining
2 - Kitchen
3 - Bedroom
4 - Living room

D623/D625 User Guide
Security System
Page 7© 2003 Bosch Security Systems 46841D
User Guide
Command Center Keys
Your Text command center has nineteen keys for performing the various functions described below:
Key Function
[1], [2], [3], [4], [5],
[6], [7], [8], [9], [0]
Numeric keys used to enter passcodes and issue commands.
[CMD] Used in conjunction with numeric keys to enter commands. Also displays
system status.
[ALL ON] Turns your system All On. See Turn the System All On on page 11.
[PART ON] Turns your system Part On. See Turn the System Part On on page 12.
[NO DELAY] Turns your system All On or Part On without entry or exit delay. See Turn the
System On with No Delay on page 14.
[BYPASS] Bypasses one or more points. See Bypass Points on page 18.
[*] When available, advances to the next display.
[A], [B], [C] Emergency functions (Fire, Panic, or Emergency Alarms) may be assigned to
these keys by your security company.
To activate the special function, press the key twice (consecutively) within 2 sec.
Your security company labels each key with its assigned function.
Command Center Tones
The command center emits several distinct tones and illuminates lights to alert you to system events.
Tone Description
Fire Alarm When fire point activates, the command center emits a repeated warble tone (on for 2 sec., then
briefly off).
Burglary Alarm When a burglary point activates while your system is turned on, the command center emits a
continuous warble tone. The sounder remains on for the duration of the time set by your security
company.
Trouble When a system component is not functioning properly, your command center emits a repeated
warble tone (on briefly, followed by a pause, followed by the warble tone). Press [4] to view the
trouble. If problem is point-related, the command center display indicates the faulted point.
Key Press Pressing any key on the command center sounds a short pip to indicate the pressed key is accepted.
Entry Delay When you enter the premises through a point programmed for Entry Delay, the command center
emits an intermittent beep to remind you to turn your system off. If the system is not turned off
before the Entry Delay expires, an alarm condition occurs and a report may be sent to your alarm
company.
Exit Delay After you turn your system on, the command center emits an intermittent beep and counts down
the Exit Delay time. If you do not exit before the Exit Delay time expires and an Exit Delay point is
faulted, an alarm event begins.
Error If you press an incorrect key, your command center emits an error tone to indicate an invalid entry.
The Error Tone is the same warble tone as the Trouble Tone, but is not repeated.
OK Indicates a command center entry is accepted, such as a correctly entered passcode. The Command
Center emits a single, high-pitched beep for 1 sec.
Watch If any watched point is faulted, the command center emits a tone to alert. The tone varies in
duration, depending on the selected Watched Tone. (See Select Watch Tone on page 31.)

D623/D625 User Guide
Page 8 © 2003 Bosch Security Systems46841D
Security System
User Guide
Command Center LED Descriptions
The command center LEDs are described below.
LED State Description
Status On No system troubles present.
Slow Flash AC failure, system trouble, or keypad was moved away from its assigned area.
Fast Flash Command center in Command Mode.
On Off Panel is disarmed.
Slow Flash Panel is armed with No Delay.
On Exit Delay timer is active or panel is armed with Entry/Exit Delay.
Commands
Commands allow you to carry out various tasks such as add/delete passcodes, set the date/time, or test the system. Each
command is detailed in this user guide.
Commands are written as: [CMD] [6] [3]. To enter this command, first press the [CMD] key, followed by the [6] key, and
then the [3] key.
System Events
Your system responds to four types of alarm events. If more than one event occurs, your system sorts them into one of four
groups: Fire Alarms (highest priority), Burglary Alarms, Fire Troubles, and Non-Fire Troubles (lowest priority). Events
grouped as highest priority are always sent to the central station first.
Fire Alarms
Fire alarms are the highest priority events. When a fire point activates, your command center emits a Fire Alarm tone. The
tone sounds for the length of time programmed by your installation company. Evacuate all occupants and investigate for
smoke or fire. Ensure all occupants know the difference between the Burglary Alarm tone and the Fire Alarm tone.
Burglary Alarms
Burglary alarms are the second priority. When a burglary point activates, your command center emits a Burglary Alarm
tone. The tone sounds for the alarm set by your security company. Ensure all occupants know the difference between the
Burglary Alarm tone and the Fire Alarm tone.
The command center scrolls through each point alarm, or you can press the [*] key to manually advance the list.
Fire Trouble Events
When a fire trouble (such as a loose wire) occurs, your command center emits a Trouble tone.
The command center displays the System Trouble message. See Check System Troubles on page 26 for more information on
determining the nature of the trouble.
Non-Fire Trouble Events
When a trouble event such as a power failure occurs, your command center emits a trouble tone.
The command center displays the System Trouble message. See Check System Troubles on page 26 for more information on
determining the nature of the trouble.

D623/D625 User Guide
Security System
Page 9© 2003 Bosch Security Systems 46841D
User Guide
How Your System Reports Alarms
Your security system may be programmed to automatically disconnect your telephone when sending reports to your security
company. Once the report is complete, the system returns the telephone to normal operation (check with your security
company).
Your system makes repeated attempts to send reports to your security company. If your system fails to report, the command
center signals a system trouble. See Check System Troubles on page 26 to determine the nature of the trouble.
I
MPORTAN
T
If your telephone service is interrupted, your security system cannot send reports to your security company unless it
has an alternate means of transmitting them.
Check System Status
When the system is Off, press [CMD] to show the current system status. The following message may appear:
System Status Message Description
System OK Indicates there are no system troubles.
System Trouble!
Press [4] to view Indicates there is a system trouble. See Check System Troubles on page 26
to determine the nature of the trouble.
Points faulted
Press [0] to view Indicates the system has faulted points. See View Faulted Points on page 18
for more information.
Log Out of the System
The system remembers passcodes entered for approximately 10 sec. after you stop pressing keys. To log out of the system,
press the [CMD] key twice. Logged Out appears on the command center display.
Silence Alarms
When an alarm occurs, the alarm tone sounds and the display shows the point(s) in alarm. If you enter your passcode
before the system dials your security company, the alarm report is aborted.
1. The command center displays the point(s) in alarm.
Enter code to
silence alarm
Alarm Pt4
Living Room
2. Enter your passcode to silence the alarm and turn the system off (if it was turned on). An alarm report is sent
to your security company if the alarm is not acknowledged in time.
The display continues to show the point (or points) that caused the alarm.
Silenced alarms
listed below
Alarm Pt8
Motion Detector
To remove
silenced alarms
from display,
hold Cmd
3. Press and hold [CMD] to remove the alarm messages from the command center display. See View Alarm
Memory on page 27 to see which points caused the alarm.

D623/D625 User Guide
Page 10 © 2003 Bosch Security Systems46841D
Security System
User Guide
Keypad Adjust (Cmd 49)
I can perform this command.
I cannot perform this comman
d.
Use Command 49 to adjust the command center sounder volume and the display brightness.
1. Press [CMD] [4] [9]. Enter a valid passcode if prompted.
2. To adjust the command center sounder volume, press and hold the [*] key and then press [1] to increase the
volume or [4] to decrease the volume.
3. To adjust the command center display brightness, press and hold the [*] key and then press [3] to increase the
brightness or [6] to decrease the brightness.
4. Press [CMD] to exit this command function when all adjustments are made.
Turn the System Off
Entry Delay Time (to be filled in by your security company).
You have __________ sec. to enter premises and turn system off.
Enter your passcode to turn the security system off. When the system is on, you must enter through a designated entry door
to prevent an alarm. Opening a designated door, such as the Front Door, starts the entry delay. During entry delay time, the
command center emits a double tone to remind you to turn the system off. Enter your passcode before the entry delay time
expires to turn the system off.
If you enter through the wrong door or fail to turn the system off before the entry delay time expires, you may cause an
alarm. If an alarm occurs, silence the alarm by entering your passcode and call your security company to let them know that
there is no emergency situation.
1. When the system is on, the On indicator illuminates. If the system is All On, the command center display
shows:
Smiths Residence
All On
If the system is Part On, the command center display shows (Part 2 On shows if the system is Part 2 On):
Smiths Residence
Part On
2. Enter your passcode to turn the system off. Once the system is off and there are no faulted points, the
command center displays the idle text (second line) as shown below:
Smiths Residence
OK for All On

D623/D625 User Guide
Security System
Page 11© 2003 Bosch Security Systems 46841D
User Guide
Turn the System All On (All On or Cmd 1)
Exit Delay Time (to be filled in by your security company).
You have __________ sec. to exit premises before system turns on.
Use this command to turn on the entire system. Once you press the [ALL ON] key or enter Cmd 1, the Exit Delay timer
starts its countdown. The length of exit delay is programmed by your security company.
When your system is ready to turn All On, it displays OK for All On, indicating all points are normal, such as no open
doors or windows and no one standing in front of a motion detector.
Smiths Residence
Ok for All On
If your command center displays a message indicating the system is not ready to arm (such as Not Ready to Arm),
check all doors and windows to see if any are open or if someone or something is in front of a motion detector. If all
protected doors and windows are closed and no motion detectors are blocked and the command center still displays Not
Ready to Arm, contact your security company for assistance.
In the example below, the exit delay is 60 sec.Leave before the exit time expires. Leaving after exit delay expires causes an
alarm event.
1. Make sure all points are normal (not faulted). If your system has a faulted point (door/window open), you
can either close it or bypass it (see Bypass Points 1 on page 18).
2. Press [ALL ON] or [CMD] [1]. The command center may prompt you to enter a valid passcode.
3. Enter your passcode if necessary. Exit delay time begins. The On indicator turns on. Exit the building now.
60 seconds to
All On.
Enter your passcode to stop the system from turning on during the exit delay.
Press [BYPASS] to bypass points (see Bypass Points on page 18). You can turn the system All On with No Delay
by pressing [NO DELAY]. You can also turn the system Part On by pressing [PART ON]. The system prompts
you through this procedure.
To bypass points
Press Bypass
Fornodelay
press No Delay
For Part On
press Part On
4. During the last 10 sec. of Exit Delay, the command center displays Do not exit! and emits a double tone
every second to warn you not to exit and to turn the system off. The system turns All On. The On indicator
remains on steady.
Smiths Residence
All On
5. To turn the system off, enter your passcode.

D623/D625 User Guide
Page 12 © 2003 Bosch Security Systems46841D
Security System
User Guide
Turn the System Part On (Part On or Cmd 2)
Exit Delay Time (to be filled in by your security company).
You have __________ sec. to exit premises before system turns on.
I can perform this command.
I cannot perform this comman
d.
Part On turns on only part of your system, leaving the rest of the system turned off.
If your command center shows OK for Part On or OK for All On, this means all of the points that turn on for
Part On operation are normal (such as all protected doors and windows bing closed).
Smiths Residence
Ok for Part On
Once you press the [PART ON] key, exit delay begins. Use Part On when you want part of your system turned on. For
example, use Part On if you plan to stay inside the premises and you only want to protect the perimeter doors, or you are
leaving and you want a pet to move freely about inside without causing an alarm.
1. Make sure that Part points are normal (not faulted). If your system has faulted points, return them to normal,
or bypass them.
2. Press [PART ON]. The command center may prompt you to enter a valid passcode.
3. Enter your passcode if necessary. The On indicator turns on and Exit delay time begins. The command center
display scrolls the following:
60 seconds to
Part On.
To bypass points
Press Bypass.
For no delay
Press No Delay.
For All On
press All On
48 seconds to
Part On.
Enter your passcode to stop the system from turning on during the exit delay. You can turn the system Part On
with No Delay by pressing [NO DELAY]. Or you can bypass points by pressing [BYPASS].
4. During the last 10 sec. of Exit Delay, the command center displays Do not exit! and emits a double tone
every second to warn you not to exit and to turn the system off. The system turns Part On. The On indicator
remains on steady.
Smiths Residence
Part On
5. To turn the system off, enter your passcode.

D623/D625 User Guide
Security System
Page 13© 2003 Bosch Security Systems 46841D
User Guide
Turn the System Part 2 On (Cmd 3)
Exit Delay Time (to be filled in by your security company).
You have __________ sec. to exit premises before system turns on.
I can perform this command.
I cannot perform this comman
d.
Part 2 On turns on the portion of your system designated as Part 2, leaving the rest of the system turned off. You can select
the points that turn on for Part 2 On, whereas Part On points are determined by your security company (see Set Part 2
Points on page 14). Once you press [CMD] [3], the exit delay timer countdown begins.
Smiths Residence
OkforPartOn
In the following example, 60 sec, is used as the Exit Delay. Exit Delay is set by your security company and may vary from the
example shown below.
1. Make sure that points are normal (not faulted).
2. Press [CMD] [3] to turn the system Part 2 On. The command center may prompt you to enter a valid
passcode.
3. Enter your passcode if necessary. The On indicator turns on. The command center display scrolls the
following: 60 seconds to
Part 2 On.
To bypass points
Press Bypass.
For no delay
Press No Delay.
For All On
press All On
48 seconds to
Part 2 On.
Enter your passcode to stop the system from turning on during the exit delay. You can turn the system Part 2
On with No Delay by pressing [NO DELAY], or you may bypass points by pressing the [BYPASS] key.
4. During the last 10 sec. of Exit Delay, the command center displays Do not exit! and emits a double tone
every second to warn you not to exit and to turn the system off. The system turns Part 2 On. The On indicator
remains on steady.
Smiths Residence
Part 2 On
5. Enter your passcode to turn the system off.

D623/D625 User Guide
Page 14 © 2003 Bosch Security Systems46841D
Security System
User Guide
Set Part 2 Points (Cmd 65)
I can perform this command.
I cannot perform this comman
d.
Use this command to program which points are armed each time you turn the system Part 2 On. This lets you turn part of
the system on to detect intrusion, while the remaining part of the system lets you move freely without sounding an alarm.
1. Make sure the system is turned off (On indicator is off).
2. Press [CMD] [6] [5]. The command center may prompt you to enter a valid passcode.
3. Enter your passcode if necessary. The command center display scrolls the following:
Pt2Part2No
Front Door
Press 2* for
Pt2Part2Yes
Pt3Part2Yes
Hallway
Press 3* for
Pt3Part2No
To exit
Press Cmd.
4. Enter the Point Number followed by the [*] key to toggle between Yes or No for Part 2 On. Repeat until all
points are programmed Yes or No for Part 2 Mode (Yes = Active, ready to detect intrusion; No = Non-Active,
you can move freely without sounding an alarm).
5. Press [CMD] to exit this command.
Turn the System On with No Delay
This command turns the system All On or Part On without entry or exit delays. Remember that turning the system on with
no delay allows no exit or entry delay time through the designated delay point, like the Front Door.
1. Make sure all points are normal (not faulted).
2. Press [ALL ON] if you want to turn the system All On, or press [PART ON] if you want to turn the system
Part On. Press [CMD] [3] if you want to turn the system Part 2 On. The command center may prompt you to
enter a valid passcode.
3. Enter your passcode if necessary. The command center display shows the following for turning the system All
On:
60 seconds to
All On.
To bypass points
Press Bypass.
For no delay
Press No Delay.
Pressing [NO DELAY] begins a 10-sec.“last chance”window in which you have 10 sec. to decide if you want to
allow the system to arm. During this window, the display scrolls through the following messages: No exit
time! System arming. Do not exit! If you decide not to allow the system to arm, enter your
user passcode.

D623/D625 User Guide
Security System
Page 15© 2003 Bosch Security Systems 46841D
User Guide
If all points are normal, the display shows the following for Part On (the display shows Part 2 On if the system
is Part 2 On):
To bypass points
press Bypass.
60 seconds to
Part On.
For no delay
Press No Delay.
4. To turn the system on (All On, Part On, or Part 2 On) with no delay, press [NO DELAY].
The command center scrolls the following for All On:
Do not exit!
No exit time!
System arming.
Enter code to
turn system off
Smiths Residence
All On
On with No Delay
The command center scrolls the following for Part On (the display shows Part 2 On if the system is Part 2
On):
Do not exit!
No exit time!
System arming.
Enter code to
turn system off
Smiths Residence
Part On
On with No Delay
5. When the system is All On with No Delay, the command center displays the following:
On with No Delay
Smiths Residence
All On
If the system is Part On or Part 2 On with No Delay, the command center displays the following (the display
shows Part 2 On if the system is Part 2 On):
On with No Delay
Smiths Residence
Part On
The On indicator turns on and blinks, indicating the system is on with no delay.
6. To turn the system off, enter your passcode.

D623/D625 User Guide
Page 16 © 2003 Bosch Security Systems46841D
Security System
User Guide
Turn the System On with No Exit Tone (Delay Silent)
Use this command to turn the entire system All On, Part On, or Part 2 On without any exit tones. Remember that turning
the system on with no exit tone eliminates the tone emitted by the command center intended to alert occupants that the
system is about to arm.
This command is useful when you wish to arm the system, but not disturb the occupants while the system counts down
prior to arming.
1. Make sure all points are normal (not faulted).
2. Press and hold the appropriate key to silence the exit tone. The command center may prompt you to enter a
valid passcode.
Arming With To Silence Exit Tone
All On Press and hold [ALL ON]
OR
Press [CMD], then press and hold [1].
Part On Press and hold [PART ON]
OR
Press [CMD], then press and hold [2].
Part 2 On Press [CMD], then press and hold [3].
I
MPORTAN
T
Silencing the Exit Delay Tone doubles the Exit Delay period.
3. Enter your passcode if necessary. The command center display shows the following for turning the system All
On:
To bypass points
press Bypass.
120 seconds to
All On.
For no delay
Press No Delay.
If all points are normal, the display shows the following for Part On or Part 2 On. If the system is turned Part
2 On, the second line of the display shows Part 2 On:
To bypass points
press Bypass.
120 seconds to
Part On.
For no delay
Press No Delay.
4. To turn the system on (All On, Part On, or Part 2 On) with no delay, press [NO DELAY]. See Turn the System
On with No Delay on page 14 for more information.

D623/D625 User Guide
Security System
Page 17© 2003 Bosch Security Systems 46841D
User Guide
Turn the System On with Points Faulted (Force Arm)
I
MPORTAN
T
Force-arming is not permitted for UL applications.
I can perform this command.
I cannot perform this comman
d.
1. Press [ALL ON] or [PART ON] to turn the system All On or Part On.
2. The command center displays the faulted points as follows:
Pt5 faulted,
Point Text
To Bypass Pt5
Press 5 + *
Then the system identifies the faulted point (in this example Point 5), followed by instructions for bypassing
the point.
3. To force arm the system All On or Part On with normal Exit Delay and exit tone, press [ALL ON] or [PART
ON] again. Enter your passcode when prompted. The following scrolls across the display:
Forced on!
60 seconds to
All On.
1 points are
forced on.
Note: The display above uses an Exit Delay time of 60 sec. and only one point is force-armed. Exit Delay time and the
number of points forced on may vary.
4. To force arm the system All On or Part On with Exit Delay doubled and no exit tone, press and hold [ALL
ON] or [PART ON] until the “point faulted”message appears (see figure in Step 2). Then press [ALL ON] or
[PART ON] again. Enter your passcode if prompted. The system then scrolls the Forced on! message and
the doubled Exit Delay Time countdown. The exit tone is silenced.
The system‘forces’ the faulted points on. As long as they remain faulted they do not provide protection. If the
faulted points return to normal before the system is turned off, they provide protection and are capable of
starting alarm events. If a point becomes faulted after the exit delay begins, the command center displays the
faulted point. If the point remains faulted at the end of exit delay, it starts an alarm event.

D623/D625 User Guide
Page 18 © 2003 Bosch Security Systems46841D
Security System
User Guide
View Faulted Points
To correctly turn your system on, all doors and windows must be in the normal (not faulted) condition. Use this command
to locate faulted points.
1. Ensure the system is turned off (On indicator off).
2. Press [*]. If points are faulted the command center displays the following:
System OK or Point faulted,
Press 0 to view
3. If there are faulted points, press [0] to view. The command center scrolls through all faulted points:
Pt7 faulted,
Back Door
Pt2 faulted,
Front Door
To bypass Pt2
Press 2 + *
To bypass Pt7
Press 7 + *
4. Return the faulted points to the normal condition (like close the front door), or you may choose to bypass the
points by following the displayed instructions (such as Press [2] [*]).
5. Once the points return to normal or are bypassed, the system is ready to turn on.
Bypass Points
I can perform this command.
I cannot perform this comman
d.
Use this command to bypass one or more points before turning the system All On, Part On, or Part 2 On. You can access a
bypassed point when the system is armed without activating an alarm.
Example: Your kitchen was just painted and you want to leave the windows open but still turn the system on. Bypassing
points allows the system to be on, but prevents it from monitoring undesired areas.
1. Ensure that the system is turned off (On indicator is off).
2. Press the [BYPASS] key. The command center may prompt you to enter a valid passcode.
3. Enter your passcode if necessary. The command center scrolls all zones that can be bypassed:
Pt1,
Front Door
To bypass Pt1
Press 1 + *.
Pt2,
Back Door
To bypass Pt2
Press 2 + *.
4. Enter the Point Number that you want to bypass followed by [*] (for example, if you want to bypass Point 10,
enter [1] [0] [*]). Repeat this step to bypass all desired points.
If a point is already bypassed, the command center displays:
Pt3
Hallway
To unbypass 3
Press 3 + *

D623/D625 User Guide
Security System
Page 19© 2003 Bosch Security Systems 46841D
User Guide
If a point is faulted, the command center displays the point number. If the point is bypassable, the command
center prompts you to press the point number followed by the [*] key. If the point is unbypassable, the display
tells you the point cannot be bypassed.
5. Press [CMD] to exit this command function.
To unbypass a point, repeat the steps above for the desired point number.
Date and Time (Cmd 45)
I can perform this command.
I cannot perform this comman
d.
Use this command to program the system date and time.
1. Ensure that the system is turned off (On indicator is off).
2. Press [CMD] [4] [5]. The command center may prompt you to enter a valid passcode.
3. Enter your passcode if necessary. The command center displays.
Please Enter
Date and Time
MM/DD/YY HH:MM
01/01/01 00:01
4. Enter the date and time using the numeric keys in MM/DD/YY, HH:MM format.
___
M__
_
M
___
H___ H
/ ___
D___ D
_
__
M___ M___ Y___ Y
/:
1 2 3 4 5
1 - Month of the year
2 - Day of the month
3 - Current year
4 - Hour of the day
5 - Minute of the hour
5. The command center displays both the date and time you entered before returning the command center to the
normal display. In this example, the command center displays.
Current Date
04/16/01
Current Time
13:35
The command center returns to the normal display.
I
MPORTAN
T
In the event of a power cycle (power is lost to the system and then restored), the panel takes the last event in the log
and uses that as a starting point for the time and date. It then alerts you to enter the current time and date.

D623/D625 User Guide
Page 20 © 2003 Bosch Security Systems46841D
Security System
User Guide
Change Passcode (Cmd 55)
I can perform this command.
I cannot perform this comman
d.
Use this command to change your passcode at any time. However, only use this feature under the direction of your
security company. The system must be off in order to use this command.
Write down your new and old passcode before you begin.
1. Make sure your system is off (On indicator is off).
2. Press [CMD] [5] [5]. The OK tone sounds and the command center displays:
Please enter
old code
3. Enter your current passcode. As you enter your passcode, the command center displays:
Entering Code
***
4. If the passcode you have entered is valid, you are prompted to enter your new passcode:
Please enter
new code
5. Enter a new passcode with the same number of digits as your old passcode. If the error tone sounds, try a
different new passcode. As you enter your new passcode, the command center displays:
Entering Code
***
6. If you have entered a valid new passcode, the command center prompts you to enter the new passcode again:
Please enter
new code again
7. Enter your new passcode again. As you enter your new passcode, the command center displays:
Entering Code
***
8. The command center displays the following to confirm you have successfully changed your passcode:
Code changed
The command center returns to the normal display.