Bradley TouchTime S45-1941 User manual

P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1-800-BRADLEY Fax: [phone]
www.bradleycorp.com
Installation
215-1378 Rev. G ECN 13-10-005
© 2013 Bradley
Page 1 of 4 3/1/2013
TouchTime®Valve
for Security Fixtures
S45-1941 TTST-15
S45-2129 TTST-15 NFC
S45-1948 TTDT-15
S45-2130 TTDT-15 NFC
S45-1940 TTST-30
S45-2184 TTST-30 NFC
S45-1949 TTDT-30
S45-2185 TTDT-30 NFC
S45-1937 LCTTFV-4
S45-2179 LCTTFV-4
S45-2181 LCTTFV-4
S45-2125 LCTTFV-4
S45-2360 URTTFV-4
S45-2395 DFTTST-15
S45-1942 SHTTST-30
S45-1943 SHTTST-60
S45-2474 SHTTST-180
S45-2668 HSC-SHTTST-60
Table of Contents
Supplies Required ...........................2
TouchTime Valve Installation ..................2
TouchTime Valve Wiring Diagram ..............3
Troubleshooting..............................4
IMPORTANT!
Read this entire installation manual to ensure proper installation.
When finished with the installation, file this manual with the owner or
maintenance department. Compliance and conformity to local codes
and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are
accounted for before discarding packaging material. If any parts are
missing, do not begin installation until you obtain the missing parts.
Make sure that all water supply lines have been flushed and then
completely turned off before beginning installation. Debris in supply
lines can cause valves to malfunction.
Your Bradley fixture MUST be connected with a 24 VAC Class II
transformer. Connection to 110 VAC or other than indicated in the
installation instructions could result in personal injury and permanent
damage to the unit. DO NOT put the transformer in the same room
where showers are used.
Product warranties may be found under “Products” on our web site
at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
Standard push button shown

TouchTime®Installation
23/1/2013 Bradley • 215-1378 Rev. G; ECN 13-10-005
To help prevent electrical damage to the unit, Bradley recommends the use of surge protection. The type of
surge protection required and its usage is the responsibility of the installer/electrician.
Supplies Required
• 110VACpowersourcefor24VACClassIItransformer
• 110/24VACClassIItransformer(availablefromBradleyasanoption)
• (3)wirenutstoconnectpowercordleadstotransformerwires
Installthe24VACClassIItransformerinaremotelocationasafedistancefromtheareawherethe
security fixture is to be used.
(Seechartonpage3for
partnumberidentication)
Mounting Bracket*
Nut
(161-080)
TouchTime Sensor
®
Escutcheon
(150-099)
Spring
(135-058)
Standard
Push Button
w/Magnet
(S08-311, COLD
S08-312, HOT
S08-313, FLUSH)
Ligature Resistant
Push Button
(S08-396)
Security Fixture
BInsert the push button and spring
into the escutcheon, then insert
the escutcheon into through the
holeinthefrontofthexture.
C
Thread the sensor through the mounting bracket and
the fixture onto the escutcheon, and secure the valve
tothexturebyturningnut1/4turnpastnger-tight).
NOTE: Use bracket part no. 140-958 for 1-5/8"
diameter hole (e.g., COMBI 5500). Use bracket
part no. 140-627 for all square-hole applications.
D
Connecttheblackandbrownpowercordleadstothe
wireonthetransformerwithwirenuts(suppliedby
installer).Turnonthewatersupplyandcheckforleaking.
Turnonthe24VACpowerandpresstheTouchTime®
pushbuttonseveraltimestopurgeairfromlines.
1Installation
A
Apply 100% silicone caulk to escutcheon
backside prior to installation to ensure a
watertightseal.Wipeexcesscaulkfrom
frontsideofescutcheonandpanel.

Installation TouchTime®
Bradley • 215-1378 Rev. G; ECN 13-10-005 3/1/2013 3
TOUCHTIME®APPLICATION WIRE COLORS SPADE CONNECTORS PART NO.
4-second cycle from release of push button Red & Gray two female S83-131A
15-second cycle from release of push button Green & Gray two female S83-131B
30-second cycle from release of push button Orange & Gray two female S83-131D
60-second cycle from release of push button White & Gray two female S83-131C
180-second cycle from release of push button Blue & Gray two female S83-131J
SOLENOID VALV ESOLENOID VALV E
BROWN WIRE
BLACK WIRE
BLACK WIRE
BROWN WIRE
TOUCHTIME SWITCH
®
OUTPUT WIRES
(see chart below for wire
color descriptions)
OUTPUT WIRES
(see chart below for wire
color descriptions)
TOUCHTIME SWITCH
®
BLACK
RED
RED
YELLOW
TAPE/WIRE NUT
(supplied by installer)
{
To Customer
120v supply
SOLENOID VALV E
BLACK WIRE
BROWN WIRE
OUTPUT WIRES
(see chart below for wire
color descriptions)
TOUCHTIME SWITCH
®
TRANSFORMER
BLACK
RED
RED
YELLOW
TAPE/WIRE NUT
(supplied by installer)
{
To Customer
120v supply
TRANSFORMER
(2) FEMALE
CONNECTORS
Transformer may be hard-wired (as shown)
or plug-in type.
TouchTime®Wiring Diagram
Wiring for
Single-Solenoid
Fixture
Wiring for
Double-Solenoid or
Triple-Solenoid Fixture
(double is shown, triple is similar)
The push button has been factory-preset to provide activation and further adjustment should not be required.
However, if adjustment is necessary, loosen the nut on the TouchTime®sensor and move the sensor in or
out until activation has been achieved. Lock the nut in place 1/4 turn past finger-tight.

TouchTime®Installation
43/1/2013 Bradley • 215-1378 Rev. G; ECN 13-10-005
Troubleshooting
If the TouchTime®push button unit does not function properly
1.Makesurethewatersupplyandthe24VACpowerarebothturnedon.
 Ifthewatersupplyandtheelectricalpowerarebothturnedonbutthepushbuttonisstillnotfunctioning,checkthewiring
followingthestepsoutlinedinprocedure#2below.
2.Checkthewiringfollowingtheprocedureoutlinedbelow:
a.Turntheelectricalpoweroff.
b.Checkthewiringforlooseconnectionsorcorrosionandcorrectifnecessary.
c. Turn the electrical power back on and retest the push button.
 If,aftercheckingthewiring,thepushbuttonisstillnotfunctioningproperly,testthetransformerfollowingthestepsoutlinedin
procedure#3below.
3.Testthetransformerwithavoltmeterfollowingtheprocedureoutlinedbelow:
a.Turnthewatersupplyoff(theelectricalpowershouldremainon).
b.Setthevoltmetertoread“24VAC.”
c.Connectthevoltmeterleadstotheblackandbrownwiresasshowninthewiringdiagramsfoundonpage4.Thevoltage
readingshouldindicate24VAC±10%.
 Ifyouareunabletoobtainapropervoltagereading,thetransformerisnotworkingproperlyandneedstobereplaced.
ContactyourBradleyrepresentativetoorderthereplacementtransformerappropriateforyourapplication.
 Ifthetransformerisworkingproperly,turnthewatersupplybackonandtestthesolenoidfollowingthestepsoutlinedin
procedure#4below.
4.Testthesolenoidvalvefollowingtheprocedureoutlinedbelow:
a.Disconnectthewhiteandgraywiresfromthesolenoid.
b.Disconnectthebrownpowercordleadsfromtheterminalblock.
c.Connectthebrownpowercordleadsdirectlytothesolenoid.Thesolenoidcoilshouldactivateandyoushouldhearasingle
click and a humming noise.
 Ifthesolenoidcoildoesnotactivate,thesolenoidvalveisnotworkingproperlyandneedstobereplaced.Contactyour
Bradleyrepresentativetoorderthereplacementsolenoidvalveassemblyorflushvalveappropriateforyourapplication.
 If,aftercheckingthetransformer,thesolenoidvalveandthewiring,youareunabletoactivatethesprayheadbypressingthe
TouchTime®push button, the TouchTime®switchassemblyisnotworkingproperlyandneedstobereplaced.Contactyour
Bradley representative to order a replacement switch assembly.