BrandMotion 9002-2738 User manual

! INSTALLATION!INSTRUCTIONS!
9002-2738.docx Page 1 of 4
2014-Current Jeep Cherokee and 2015-Current Chrysler 200
Backup Camera Interface
(Kit # 9002-2738)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Tools & Supplies Needed:
9002-2738 module
T-harness w/video RCA
USB to mini USB for updating
These instructions
Plastic panel removal tool
Phillips screwdriver
Wire cutters
Wire strippers
Electrical tape
Zip ties
Safety Precautions:
• Work in well ventilated area that is clear of obstructions.
• Secure vehicle with tire chucks in both front and rear of tires.
• Turn vehicle accessories OFF and ensure ignition key is in OFF position.
• Wear safety goggles and snug fitting clothes.
• Use tools only for their intended purpose and which are in good repair.
• Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
Install in a 2015 Jeep Cherokee
1. Remove the climate control panel with a
plastic panel removal tool.
2. Disconnect the climate controls harness and
set aside.
3. Remove (2) Phillips screws that hold the
radio trim to the main dash.

! INSTALLATION!INSTRUCTIONS!
9002-2738.docx Page 2 of 4
4. Pull the vent trim towards you after
removing the (2) trim screws from the
bottom. It has plastic clips around the trim
holding it into place.
5. Remove the (4) Phillips screws that are
holding in the radio to the dash. Remove
the radio from the dash, disconnect all the
harness from the back of the radio and set
it side.
This section is for 5” radio models
only. See next section for 8.4”
radios.
Leave ignition off until installation
is complete.
1. After removing the radio connect the female
side of the Plug and Play T-harness to the
factory 44-pin harness that was unplugged
from the radio.
2. Run the camera power and video RCA up to
the radio opening.
3. Connect the video RCA from the camera to
the Yellow female RCA on the T-harness.
4. Connect the power for the camera to the
white/red wire marked ACC OUT from the
T-harness.
5. Ground the camera to a good solid metal
ground.
6. Connect the 18-pin connector on the T-
harness to the 9002-2738 module.
7. Connect the male connector of the T-
harness to the back of the radio. Connect all
other harness that where unplugged from
the radio.
8. Mount module securely in dash with zip ties
or Velcro. Reinstall radio into opening. Take
care not to pinch any harness when putting
radio back in.
9. Turn the key to the ON position (don’t start
vehicle).
10. The radio will turn on, and restart itself
within 1 minute.
11. Re-cycle the key one time (turn the key to
OFF then back again to ON0. Wait for the
radio to boot and settle.

! INSTALLATION!INSTRUCTIONS!
9002-2738.docx Page 3 of 4
12. If programming of the radio took
successfully, the camera (or blue screen)
will display on screen while in reverse.
Below is a chart referencing LED flashes, which
can be found on the side of the module.
This section is for 8.4” radio models
only. See pervious section for 5”
radios.
Leave ignition off until installation
is complete.
1. After removing the radio connect the female
side of the Plug and Play T-harness to the
factory 44-pin harness that was unplugged
from the radio.
2. Run the camera power and video RCA up to
the radio opening.
3. Connect the video RCA from the camera to
the Yellow female RCA on the T-harness.
4. Connect the power for the camera to the
white/red wire marked ACC OUT from the
T-harness.
5. Ground the camera to a good solid metal
ground.
6. Connect the 18-pin connector on the T-
harness to the 9002-2738 module.
7. Connect the male connector of the T-
harness to the back of the radio. Connect all
other harness that where unplugged from
the radio.
8. Mount module securely in dash with zip ties
or Velcro. Reinstall radio into opening. Take
care not to pinch any harness when putting
radio back in.
9. Turn the key to the ACC position (not the
ON, don’t start the vehicle).
10. Temporarily connect input 3 (pink wire) to
+12 volts.
11. Turn the key to the ON position. The radio
will reboot within 20 seconds.

! INSTALLATION!INSTRUCTIONS!
9002-2738.docx Page 4 of 4
12. While the radio is rebooting, remove the
+12 volts from input 3 (pink wire).
13. Wait for the radio to boot and settle.
14. If programming of the radio took
successfully, the camera image (blue
screen) will display on screen while in
reverse. If nothing happens in reverse,
recycle the key and place the vehicle in
reverse once more.
Below is a chart referencing LED flashes, which
can be found on the side of the module.