9
• Turn the cup upside down, position the line on
the locking ring (13c) in front of you and push the
cup down until it is securely locked into place.
• Plug in the power cord.
• Turn the appliance on by pressing the On/Off
button (7).
• The On/Off button will illuminate and all other
indicator lights (8,9,10) will flash. The blender is
in ON mode, but no speed has been selected.
To select a pre-programmed speed, refer to
«Operating Instructions».
• When finished, press the pre-selected speed
button.
• To switch off the appliance, press the On/Off
button and unplug blender before removing the
Smoothie2Go attachment.
• Turn the cup upright and unscrew the blade
assembly.
• To remove the blade group from the locking ring,
push with both thumbs from inside the ring until it
snaps out.
• To attach the lid to the cup, ensure the gasket
(12b) is inside the rim of the lid (12a) and twist
clockwise. Carefully close the drinking spout.
NOTE: The Smoothie2Go attachment must not be
used to blend hot foods or carbonated liquids.
Operating Instructions
NOTE:
The blender will only operate when the On/Off button
is pressed before selecting the desired speed or
mode.
If the appliance is turned on and no speed or mode
is selected, it turns off automatically after 5 minutes.
To turn the appliance on again, press the On/Off
button.
Speed Selection
• Start blending by pressing one of the speed
buttons (9).
• The indicator light of the selected function will
glow and all other lights will turn off.
• Change the operating speed by pressing a higher
or lower speed button.
• To stop blending, press the selected speed
button again.
• When finished, press the On/Off button (7) to
switch off the appliance. Unplug blender.
Pulse Mode (type 4142 + 4143)
The pulse mode can be used to break apart larger
pieces of food or to control the texture of food when
chopping. It can be activated with any speed.
• Press the pulse button (8).
• The indicator light will glow and the indicator
lights of each speed program will flash to signify
all speeds are in pulse mode.
• Start pulsing by pressing one of the speed
buttons (9). Hold the selected speed button as
long as the pulse mode should run. You determine
the duration of each pulse.
• To finish the pulse mode, press the pulse button
again.
• When finished, press the On/Off button (7) to
switch off the appliance. Unplug blender.
Pulse Mode (type 4144)
• Press and release the pulse button (8) for short
bursts of power. You determine the duration of
each pulse. Repeat as desired.
• When finished, press the On/Off button (7) to
switch off the appliance. Unplug blender.
NOTE: Pulse mode will not work with the crush ice
feature.
Crush Ice Mode
When selected, the blender will automatically run
at staggered intervals (30 seconds) at a pre-set
speed.
• Press the crush ice button (10) to begin crushing.
• The indicator light will glow.
• The blender will cycle through a pre-programmed
time and stop automatically when finished.
• To stop the program earlier, press the crush ice
button again.
• When finished, press the On/Off button (7) to
switch off the appliance. Unplug blender.
For Best Results
• When mixing solid ingredients, cut them up into
small pieces (1 inch).
• Always start by mixing solid ingredients with a
small amount of liquid. Then gradually add more
liquid.
• When pureeing solid ingredients, feed small
portions into the pitcher (4/4a) gradually rather
than adding a large quantity at one time.
• If blending action stops during blending or
ingredients stick to sides of the pitcher, there may
not be enough liquid to blend efficiently.
• Use the pulse mode when mixing solid or highly
viscous ingredients to avoid the blade becoming
stagnant
• For preparing small amounts of foodstuff use a
low speed level.
2231046IBR_JB7192-7172-7130-7000_USCA_S6-24.indd 92231046IBR_JB7192-7172-7130-7000_USCA_S6-24.indd 9 04.11.15 15:2804.11.15 15:28
