BRAVILOR BONAMAT FreshOne User manual

26.4
26.5
26.7
26.6
1
2
3
4
5
7
8
6
910111213
14
15
16
26.1
26.2
26.3
24.1
24.2
24.3
24.4
24.5
24.6
24.7
24.11
24.10
24.9
24.8
29
28
27
26
25
24
17 18
19
20
21
23 22

378 55
476
990
748
59162
W=41
E=41
WE
114
189

GB
Bravilor Bonamat
Operating Instructions
FRESHONE
700.403.291B
Bravilor Bonamat
3–2001
Bravilor Bonamat
Pascalstraat 20
1704 RD Heerhugowaard
The Netherlands

GB
All rights reserved.
No part of this document may be copied and/or published by means of printing, photocopying,
microfilming or by any other means whatsoever without the prior written consent of the manufacturer.
This applies equally to the included drawings and/or diagrams.
The information contained in this document is based on general data concerning the construction, materials
characteristics and working methods known to us at the time of publication and therefore we reserve the
right to make changes without notice. For this reason the instructions contained in this document should be
treated as a guide to the installation, use and maintenance, of the machine indicated on the front cover.
This document applies to the standard version of this machine. The manufacturer therefore accepts no
liability for any damage arising from specifications that deviate from the standard version of the
machine as delivered to you.
Every possible care has been taken in the production of this document, but the manufacturer accepts
no liability for any errors in this document or for any consequences arising therefrom.
TAKE THE TIME TO CAREFULLY READ THIS DOCUMENT BEFORE USING THE MACHINE.
DURING READING KEEP THE FOLD–OUT OPEN.
ALWAYS KEEP THIS DOCUMENT NEAR THE MACHINE.

GB
ECopyright Bravilor Bonamat B.V. I
version 1.0
PREFACE
Using this document
This document is intended to provide instructions for authorized users qualified technicians to safely
install, use and maintain and repair the machine.
The words ”left”, ”right”, ”front”and ”back”are used in this document to indicate a particular part of the
machine. The point of departure here is the position of the user standing at the operating side.
The position numbers 1.–29. used in this document refer to the figures in the fold–out. On this same
sheet the compositions 24. and 26. are specified in more detail. The further elaborated compositions 5.
and 19. are dealt with in fig.2 and 3 respectively.
Icons and symbols
To the machine the following safety icons and symbols are applied.
WARNING
nRisk of electric shock.
WARNING
nProcedures that can result in serious damage to the machine or in physical injury if they are not
carried out with due care.
In this document the following icons and symbols can be found:
TIP
–Hint, suggestion or advice to carry out certain tasks more easily or neatly.
CAUTION!
–Procedures that can result in damage to the machine, the surrounding area or the environment if
they are not carried out with due care.
WARNING
nProcedures that can result in serious damage to the machine or in physical injury if they are not
carried out with due care.
Related documents
The following related documents are available:
–FreshOne maintenance manual : 700.703.Lxx
–Coin mechanism operating Instructions : 700.703.298
–Coin mechanism maintenance manual : 700.703.Nxx
Document code
Document codes consist of two fields:
–Field 1: document number (if required followed by the revision number)
–Field 2: revision date

GB
version 1.0 ECopyright Bravilor Bonamat B.V.
II
Service and technical support
Please contact your dealer for information concerning the specific setting, maintenance or service
activities that fall outside the scope of this document. He will always be happy to help you. When doing
this, always ensure that you have the following details at hand:
–Model code
–Type number
–Serial number
These data can be found on the identification plate. Write down the data of the identification plate in
the intended fields (fig.1 ).
Guarantee conditions
The guarantee conditions applicable to this machine form part of the terms of delivery.
Identification of the machine
MODEL :
TYPE :
VLGNR :
230V
12
4
3
56
50/60HZ 2025W
VHH
PATENTED
Fig. 1 Identification plate
1. Model code
2. Type number
3. Serial number
4. Output capacity
5. Frequency
6. Supply voltage

Table of contents
GB
ECopyright Bravilor Bonamat B.V. III
version 1.0
Preface I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using this document I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Icons and symbols I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related documents I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Document code I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service and technical support II. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guarantee conditions II. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Identification of the machine II. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety instructions and danger warnings VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instructions for use VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Icons and instructions on the machine (if present) VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Users VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Proper use VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical specifications VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modifications VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation VII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use VII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance and repairing failures VII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety devices present VIII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Machines and the environment VIII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packaging material VIII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disposal of the machine VIII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 General description 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Main components 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.1 Outside 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.2 Inside 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Technical data 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 General 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Dimensions 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Electrical system 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 Water system 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5 Capacity 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6 Environmental conditions 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7 Recommended cleaning and descaling materials 2. . . . . . . . . . . . . . . . . . .
2.8 Recommended coffee and filter paper 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. Installation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Unpacking 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Installation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1 Boiling programme 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2 Fill 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Initial use 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1 Coffee system 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2 Hot water system 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. Operation 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Controls 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.1 Operating panel front 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.1.1 Display 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.1.2 Buttons and keys 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.2 Operating panel inside 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.2.1 Electronic control 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.2.2 Keys on the electronic control 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of contents
GB
version 1.0 ECopyright Bravilor Bonamat B.V.
IV
4.2 Daily use 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1 Tap cup 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2 Tapping mug, half a jug or whole jug 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3 Indicator ‘drip–tray full’7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4 Raising the machine 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5 Automatic stop functions 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5.1 Filter paper is finished 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5.2 Litter bin is full 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Maintenance by users with limited authority 9. . . . . . . . . . . . . . . . . . . . . . .
5.1 Daily 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1.1 General 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1.2 Emptying drip–tray and litter bin 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1.3 Checking the supply in the ingredients container 9. . . . . . . . . . . . . . . . . . . . . . . .
5.1.4 Placing a roll of filter paper 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1.5 Rinsing programme 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Weekly 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.1 General 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.2 Cleaning outside 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.3 Cleaning inside 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.3.1 Cleaning brewer 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.3.2 Cleaning ingredients container 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. Use of the programming unit 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 Reading out the counter contents or re–setting the counter 13. . . . . . . . . .
6.1.1 Reading counter positions of tapped drinks 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.2 Reading counter positions per drink 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.3 Resetting the counter positions to zero 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Setting possibilities 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1 Setting the amount of drink 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2 Switching on or off the tapping possibilities ‘mug, half a jug or whole jug’14. . .
6.2.2.1 Switching off 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2.2 Switching on 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.3 Setting strongness of drink 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.4 Brewer stops 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.4.1 Setting the brewer stops 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.5 Setting the hot water temperature 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.6 Setting descaling signal 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.7 Setting the ‘litter bin full’indication / stop function 17. . . . . . . . . . . . . . . . . . . . . . . .
6.2.7.1 Switch off the ‘litter bin full’indication 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. Maintenance by authorized users 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1 Descaler 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2 Cleaning the exhaust fan 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. Correcting malfunctions 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 Malfunctioning analysis general 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2 Malfunction analysis brewer 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3 Display messages and their meanings 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. Consumable items and accessories 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1 Recommended consumable items 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2 Accessories 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2.1 Raising feet 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2.2 Worktop feed–through 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of figures
GB
ECopyright Bravilor Bonamat B.V. V
version 1.0
Fig. 1 Identification plate II. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 2 Operating panel front 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 3 Operating panel inside 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 4 Filter paper finished 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 5 Litter bin full 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 6 Feeding diagram filter paper 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 7 Flushing programme 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 8 Coffee deposit 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 9 Counter positions 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 10 Initial situation programming 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 11 Setting the amount of drink 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 12 Initial situation programming 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 13 Strongness drink 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 14 Setting brewer stop 1 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 15 Setting brewer stop 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 16 Temperature setting 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 17 Descaling signal 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 18 Litter bin indication 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 19 Descaling signal 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 20 Descaling programme 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 21 Raising foot 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fig. 22 Worktop feed–through 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GB
version 1.0 ECopyright Bravilor Bonamat B.V.
VI
Safety instructions and danger warnings
General
The manufacturer accepts no liability whatsoever for damage or injury resulting from a failure to
(strictly) observe the safety instructions contained in this document or resulting from negligence during
the installation, use or maintenance of the machine specified on the front cover of this document or of
any related accessories.
Additional safety instructions may be required, depending on the specific working conditions required
for the accessories used. Please contact your dealer if you think there may be any potential danger in
using the machine.
The full responsibility for observing the local safety instructions and regulations always rests
with the user of the machine.
Instructions for use
DEach person working with the machine should know the contents of this document and carefully
follow the instructions contained. The management must instruct the personnel on the basis of this
document and take all the instructions and recommendations into account.
DNever change the order in which activities must be carried out.
DAlways keep this document near the machine.
Icons and instructions on the machine (if present)
DIcons, warnings and instructions attached to the machine form part of the safety provisions. They
must not be covered or removed and they must be present and remain legible throughout the life of
the machine. Any icon, warning or instruction that becomes illegible must be repaired or replaced
immediately.
Users
DThe machine may only be used by properly trained and authorized persons. Temporary staff and
persons undergoing training may only use the machine under the supervision and responsibility of
authorized users.
Proper use1
The machine is exclusively designed for delivering coffee and hot water. Any other or further use is not
in conformity with the purpose. The manufacturer does not accept any liability for damage or injury
resulting from this. The machine meets the current standards and guidelines. Use the machine only if it
is in perfect technical condition and only for the proper purpose as described above.
Technical specifications
The specifications given in this document may not be modified.
Modifications
Modification of (parts of) the machine is not allowed.
1. ”Proper use”as laid down in EN 292–1 is the use for which the technical product is suitable as stated by
the manufacturer –including any instructions in the sales brochure. In cases of doubt, it is the use that is
evident from the construction, version and function of the product. Proper use includes taking into account
the instructions included in the ”instructions for use”.

GB
ECopyright Bravilor Bonamat B.V. VII
version 1.0
Installation
DThe maximum acceptable ambient temperature with which a good operation can be guaranteed is 40°C.
DConsider damage caused by freezing. Never place the machine in rooms in which the temperature
can drop below 0°C. After all, with normal use there will always be water in the machine.
DDo not turn over the machine, move it upright.
DNever install the machine in places where water is sprayed or sprinkled.
DNever install the machine in front of entrances, exits or passageways intended for emergency services.
DPlace the machine on a sufficiently solid, flat surface close to a water connection, water discharge
and an earthed electrical power outlet.
DConnect the machine to the electrical supply in such a way that the power can easily be disconnected.
DLeave sufficient space at the back and front of the machine for maintenance and repair purposes.
DAt the left of the machine leave a space of at least 5 cm. for ventilation.
DConnect the machine to a readily accessible, manually operated water tap, so that the water supply
can easily be turned off.
DAlways observe local rules and standards when installing this machine.
Use
DInspect the machine before use and check for damages.
DProtect the machine against water and moisture. Do not wet the machine by spraying and never
submerge the machine in water.
DKeep the operating controls free from dirt and grease.
DNote that during use some parts of the machine become very hot.
DDisconnect the electricity grid and the water supply when the machine will not be used for a longer
period. Clean the machine following the instructions in chapter 5. Make sure that there is no coffee left
in the ingredients container and empty the litterbin to avoid moulding. Discharge the water (chapter 7.).
Maintenance and repairing failures
DRepair and maintenance activities not included in this document must always be carried out by
service mechanics.
DIf the mains lead is visibly damaged, it has to be replaced by a qualified service technician.
DObserve the given maintenance intervals. Overdue maintenance can lead to high repair costs and
may cause guarantee claims to become invalid.
DDo not carry out any maintenance activities concerning the machine before having it protected
against unintentional coming into operation. In such cases disconnect the electricity grid.
DAvoid contact with moving parts.
DNever leave the machine during maintenance activities.
DFor cleaning the machine only use the cleansing agent and descaler recommended by the manufacturer.
DAlways wear suitable facial protection and gloves while working with cleansing and descaling
materials. Wash your hands after using these materials.
DPrevent damage of the machine caused by spilled descaler solution. Remove spilled solution as
quickly as possible and follow the previously mentioned safety instructions.

GB
version 1.0 ECopyright Bravilor Bonamat B.V.
VIII
Safety devices present
The machine is default provided with the following safety devices:
–Using the ON/OFF–switch the machine is switched on or off. After switching off there is still some
residual voltage in the electrical system. Remove the plug from the wall outlet in order to take away
this residual voltage.
–Electrical fuse of electronic components that is activated as soon as the power drop exceeds the
allowed maximum value due to a power failure.
–Thermal safety device that interrupts the power when the water temperature in the boiler becomes
too high.
–Boiling protection that interrupts the power when the boiler temperature becomes too high.
–Overflow protection that prevents the machine from taking in more water than allowed.
–Emergency stop to interrupt a selection of the amount of fluid (cup, half a can or whole can). The
cycle started last is finished.
–Drip–tray with float indication and discharge possibilities to prevent trouble caused by spilled drink.
–Automatic stop function when the filter paper is finished.
–Automatic stop function (counter) when the litterbin is full.
–Automatic stop function when there is a leakage in the machine or when boiling over.
Machines and the environment
Packaging material
The main components of the packaging material for transport and protection of the machine are the
following:
–Corrugated board
–Polystyrene elements
Generally, the packaging material can be returned through your dealer after installation of the machine.
If this is not be possible, ask your local authority refuse department how you can dispose of the
materials.
Disposal of the machine
Machines that you wish to dispose of can usually after consultation be returned to your dealer. If this is
not possible, inquire with your local authority about the possibilities for re–use or
environmentally–friendly processing of the materials. All plastic parts have been clearly coded for this
purpose. The printed–circuit board in the machine and the components connected to this should be
consigned to electrical or electronic refuse.

GB
version 1.0ECopyright Bravilor Bonamat B.V. 1
1. INTRODUCTION
1.1 General description
The FreshOne is a hot drinks machine designed for the distribution of coffee and hot water. The
personnel responsible for the operation can change the factory settings in the programmable control.
Once programmed and set conform the specific wishes and requirements, the machine can be easily
operated by the consumer through the operating panel (with display) at the front.
If the machine is provided with a coin mechanism, the installer can the installer can set the prices
through the programmable control.
1.2 Main components
The machine consists of the following main components (see the fold out):
1.2.1 Outside
1. Lid
2. Coin mechanism (optional)
3. Door
4. Window + text plate
5. Operating panel front
6. Hot water outlet
7. Coffee outlet
8. Drip–tray plate
9. Drip–tray
10. Indicator ‘drip–tray full’
11. Foot (4x)
12. Lock
13. Identification plate
14. Mains cable
15. Water connection
16. Ventilation grille
1.2.2 Inside
17. ON/OFF switch
18. Brush
19. Operating panel inside
20. Drain hose
21. Hot water outlet hose
22. Service key opening
23. Litterbin
24. Brewer
24.1 Brewer room
24.2 Mixing basin
24.3 Locking spring hot water hose
24.4 Conveyor wheels
24.5 Conveyor roller
24.6 Outlet port
24.7 Coffee outlet piece (rubber)
24.8 Coffee outlet piece (plastic)
24.9 Piston
24.10 Drive
24.11 Paper guide
25. Hot water supply for Brewer
26. Ingredients container assembly
26.1 Lid
26.2 Ingredients container
26.3 Outlet (discharge opening)
26.4 Fixing cam
26.5 Worm (plastic)
26.6 Drive clutch
26.7 Agitator
27. Paper roll holder
28. Filter paper
29. Pouring opening descaler

GB
version ECopyright Bravilor Bonamat B.V.21.0
2. TECHNICAL DATA
2.1 General
Model : Frshn–001
Weight (empty) : 22,3 kg
2.2 Dimensions
DSee the fold out.
2.3 Electrical system
DSee the identification plate for the correct values.
2.4 Water system
Water hardness : min. 5 _dH
Min. water pressure (supply) : 100 kPa (1 bar)
Max. water pressure (supply) : 1000 kPa (10 bar)
Flow–rate : 2 l/min
Conductivity : q35 µSiemens/cm
Boiler capacity : 1 liter
Delivery time per cup (125 ml) : 8 seconds
2.5 Capacity
Start–up time : 2 minutes
Delivery time per cup (125 ml) : 20 seconds
2.6 Environmental conditions
In view of danger of freezing the machine may never be placed in rooms where the temperature can
fall below 0_C.
2.7 Recommended cleaning and descaling materials
Cleaning material : CLEANER
Descaler : RENEGITE
CAUTION!
–Before use first read the instructions on the packing.
See chapter 9. for ordering cleaner and descaler.
2.8 Recommended coffee and filter paper
For this machine the use of special Fresbrew grind is recommended.
Exclusively use the provided Bravilor Bonamatfilter paper or filter paper of the same quality. See
chapter 9. for ordering consumable goods.

GB
version 1.0ECopyright Bravilor Bonamat B.V. 3
3. INSTALLATION
3.1 Unpacking
DCheck whether the machine is complete. The contents of the packaging consist of:
–1 FreshOne hot drinks machine
–1 drip–tray (complete with drip–tray plate)
–1 water connection hose
–1 water hose (for descaling)
–1 roll of filter paper (200 measures)
–1 sachet of CLEANER
–1 sachet of RENEGITE descaler
–1 funnel (for descaling)
–1 tool for turning the Brewer
–1 brush for cleaning places in the machine that are difficult to reach
–1 scrubbing brush for cleaning the ingredients container
–1 service key
–2 door keys
–2 keys for till (only with coin mechanism)
–This manual
–manual coin mechanism (only with coin mechanism)
DPlease contact your dealer if components are missing or damaged.
3.2 Installation
DPlace the machine on a flat (max. 5_off
plumb), sufficiently solid surface near a water
connection point (and if possible a water
discharge) and an electricity connection point
that is earthed.
DLeave sufficient space for maintenance and
repair purposes at the back and front of the
machine.
DLeave a space of at least 5 cm at the left side
of the machine for ventilation!
DConnect the machine to a readily accessible
manually operated water tap, so that the water
supply can easily be turned off. Use the water
connection hose provided for this.
DOpen the tap.
DOpen the door (3.) on the left side with the key.
DRemove the polystyrene transportation block
between the Brewer (24.) and the upper and
lower sides of the ingredients container (26.).
WARNING
nPower supply voltages vary from one country
to another. Ensure that the machine is
suitable for connecting to the local power
supply. Details on the required supply voltage
and frequency can be found on the
identification plate.
Follow the instructions below to install another
language with drink names:
DRemove the window (4.) with the name plate.
–Press the plastic lips of the window from the
inside of the machine to the outside.
–Remove the window and the name plate.
DPlace the multilingual, double–sided leaf with
drink names behind the name plate. Now you
can read the drink names in the required
language through the openings.
DRemount the window with the name plate.
DConnect the plug to the power socket.
DClose the door.

GB
version ECopyright Bravilor Bonamat B.V.41.0
3.2.1 Boiling programme
WARNING
nDuring determining the boiling point hot water
can come out of the hot water outlet.
Only with putting for the first time into operation
of the FreshOne, the machine automatically
works through a boiling programme to
determine the boiling point of the water. This is
necessary because the boiling point depends on
the local atmospheric pressure. Thus, the boiling
point at sea level will be about 100_C, whereas at
2.000 m height it will be about 97_C.
After switching on the mains voltage, the water in
the boiler is first heated with full power until 80_C.
After that the water is heated with reduced power
until the boiling point is reached. The temperature
of the boiling point is now recorded in the
machine.
During the boiling programme the display shows
‘100_C’with below that a flashing thermometer.
After 10 to 15 minutes the thermometer stops
flashing. The water in the boiler must first cool
down until the set operating temperature (§6.2.5).
To avoid waiting, you can press key (5.6) after
which the machine measures hot water and takes
in cold tap water. This speeds up the cooling
down of the water in the boiler and the machine is
ready for use.
DSwitch the machine on by turning the ON/OFF
switch (17.) to ON. A little red square appears
on the switch. The machine starts filling up with
water. On the display all fields light up for a
moment.
DClose the door. All symbols on the display light
up for a moment.
3.2.2 Fill
DOpen the door.
DSwing up the cover (1.) of the machine.
DRemove the cover (26.1) from the ingredient
container. Fill the ingredients container with a
Freshbrew grind to be used with this machine.
DPut back the cover on the ingredients
container.
DPlace the filter paper (§5.1.4).
DClose the cover (1.) and close the door (3.)
with the key.
TIP
–It is possible to mount a discharge hose on
the drip–tray. At the back of the drip–tray
there is a spout. Bore a hole in this and slide
the hose on.
DPlace the drip–tray (9.) in front of the machine.
TIP
–It is possible to place the machine in such a
way that the used coffee filter paper is not
collected in the machine, but below the
worktop. For this you can make an opening in
a part of the litter bin especially marked for
this (23.) and in the bottom of the machine
containing a part that can easily be removed.
You also should make an opening in the
worktop, right below the machine. In this way
the finished filter paper can be collected in a
litter bin with a larger capacity placed under
the worktop.
–Your specialist can supply a lead–through for
the worktop as accessory (§9.2.2).
ÓÓÓ

GB
version 1.0ECopyright Bravilor Bonamat B.V. 5
3.3 Initial use
CAUTION!
–Inspect the machine before use and check for
damages.
–Protect the machine against water and moist.
Do not wet the machine by spraying and
never submerge it in water.
–Keep the operating controls free from dirt and
grease.
–Note that during use some parts of the
machine become very hot.
At coming into operation the machine has the
default factory settings. If required, these settings
can be adjusted (chapter 6.).
3.3.1 Coffee system
DPlace an empty cup under the Coffee outlet
(7.).
DPress the Selection button (5.1, fig.2 ) ‘regular
coffee’.
–The selection is confirmed by a beep. Only
the dot on the display at the selected drink
remains after which the drinks flows into the
cup. During the filling the cup on the display
flashes and the tapping cycle is displayed by
a circle building up with segments.
DThrow away the content of the first two cups.
DCheck for the 3rd cup whether the taste and
the amount are right. If so, the system is ready
for use. If not, correct the taste and/or amount
(§6.2).
3.3.2 Hot water system
DPlace an empty cup under the hot water outlet
(6.).
DPress the Selection button (5.5, fig.2 ) ‘hot
water’.
–The selection made is confirmed by a beep.
Only the dot on the display at the selected
drink remains after which the water flows
into the cup. During the filling the cup on the
display flashes and the tapping cycle is
displayed by a circle building up with
segments.
The system is now ready for use.

GB
version ECopyright Bravilor Bonamat B.V.61.0
4. OPERATION
4.1 Controls
The machine is provided with two operating
panels, one at the front (fig.2 ) and one at the
inside (fig.3 ). During normal daily use of the
machine by the consumer, only the operating
panel at the front is used. For programming and
specific activities the operating panel at the inside
is important as well.
4.1.1 Operating panel front
5
<>
5.1
5.2
5.3
5.4
5.5
5.65.75.8
Fig. 2 Operating panel front
4.1.1.1 Display
DThe display (5.) shows during normal use while
programming, rinsing or descaling the machine
and in the case of failures various symbols,
values and messages that will be explained in
this manual. Fig.2 displays the basic position
(operational position).
4.1.1.2 Buttons and keys
5.1 Selection button ‘regular coffee’
5.2 Selection button ‘mild coffee’
5.3 Selection button ‘strong coffee’
5.4 Selection button ‘extra strong coffee’
5.5 Selection button ‘hot water’
5.6 Setting key [>]
5.7 Enter key (blocked during normal use of
the machine)
5.8 Setting key [<]
The setting keys (5.6 and 5.8) have more than
one function. During normal use of the machine
these keys are only used to choose between cup,
mug, half a jug and whole jug respectively).
The [Enter] key (5.7) is blocked during normal
use of the machine.
4.1.2 Operating panel inside
19.1
19.2
19.3
19.4
19
Fig. 3 Operating panel inside
4.1.2.1 Electronic control
The housing of the electronic control with
operating panel (19.) of the machine is found at
the inside of the door (3.). The four keys are for
service and maintenance activities.
4.1.2.2 Keys on the electronic
control
19.1 Key ‘reset counter litter bin’
19.2 Key ‘open/close Brewer’
19.3 Key ‘rinse’
19.4 Programming key
While the machine is in use, the factory default
settings may appear to be incorrect or insufficient
for the situation in which the machine is used.
These settings can be adjusted following the
instructions in §6.2.
The present chapter (4.) therefore only describes
the normal daily use of the machine.
Periodic maintenance by users with limited
authority is described in Section 5.

GB
version 1.0ECopyright Bravilor Bonamat B.V. 7
4.2 Daily use
DSwitch the machine on with the ON/OFF
switch (17.) behind the door (3.). When the
machine is on there is a little red square visible
on the switch. During warming up a flashing
thermometer appears in the upper right corner
of the display. Tapping is only possible after the
thermometer has disappeared from the display.
4.2.1 Tap cup
You can only select those drinks that are
indicated on the display by a black dot.
DPlace an empty cup under the Coffee outlet
(7.).
DSelect a drink with one of the selection buttons
(5.1 –5.4).
–The selection made is confirmed with a
beep. On the display only the dot with the
selected drink remains after which the drink
flows into the cup. During the filling the cup
flashes on the display and the tapping cycle
is displayed by a circle building up with
segments.
4.2.2 Tapping mug, half a jug
or whole jug
TIP
–After 5seconds the setting automatically
returns to tapping a cup.
–For ‘extra strong coffee’it is only possible
to tap a cup (see for adjusting the settings
§6.2.2).
DSelect with the setting key (5.6 or 5.8) mug,
half a jug or whole jug.
TIP
–If a thermometer appears on the display the
temperature is (temporarily) too low caused
by tapping too much water. The machine is
blocked until the temperature is right again.
DPlace an empty mug or jug under the Coffee
outlet (7.).
DMake a selection with one of the selection
buttons (5.1 –5.4) for a drink.
–The selection made is confirmed with a
beep. On the display only the dot with the
selected drink remains after which the drink
flows into the mug or jug. During the filling
the cup flashes on the display and the
tapping cycle is displayed by a circle building
up with segments.
TIP
–By pressing any selection button after having
selected a mug, half a jug or a whole jug you
prevent the machine from really executing
this task. The machine is now limited to
tapping just one cup.
4.2.3 Indicator ‘drip–tray full’
The float indication (10.) will come up at reaching
the maximum level of spilled drink. In this case,
empty the drip–tray as soon as possible!
4.2.4 Raising the machine
When you use a mug or jug that does not fit
under the drink outlet you can temporarily
remove the drip–tray.
If necessary, the machine can be raised 2 cm
with a set of raising feet to increase the distance
between the drink outlets and the drip–tray. Such
a set can be ordered as accessory with your
specialist (§9.2.1).

GB
version ECopyright Bravilor Bonamat B.V.81.0
4.2.5 Automatic stop functions
During use the following signals can appear on
the display which automatically block the
operation of the FreshOne.
4.2.5.1 Filter paper is finished
Fig. 4 Filter paper finished
The FreshOne automatically stops delivering
coffee when the filter paper is finished. The
display now shows a flashing roll of filter paper.
TIP
–The roll of filter paper supplied is enough for
200 measures.
DPlace a new roll of filter paper (§5.1.4).
After having placed the new roll the machine is
ready for use again; the roll of filter paper
disappears from the display.
4.2.5.2 Litter bin is full
Fig. 5 Litter bin full
When the litter bin is full the FreshOne
automatically stops delivering coffee (the counter
has reached the set maximum number of
measures). Now a litter bin appears on the
display.
After 90 measures first a flashing litter bin
appears, at a 100 measures the machine stops
delivering coffee and the litter bin is shown
constantly on the display (see §6.2.7 for other
settings than the factory settings).
DEmpty the litter bin
DPress key (19.1) to reset the machine.
The litter bin disappears from the display and the
machine is ready for use again.
TIP
–The number of measures after which the
machine must stop because the litter bin is
full can be decreased or switched off
(§6.2.7.1).
–The litter bin in the machine can maximally
contain filter paper for 100 measures.