BRAYER BR1103 User manual

Instruction manual
Инструкция по эксплуатации
Coffee maker BR1103
Кофеварка BR1103
brayer.ru

СОДЕРЖАНИЕ
EN......................................................................................................................................3
DE....................................................................................................................................14
RU ...................................................................................................................................26
KZ....................................................................................................................................38

3
EN
ATTENTION!
For additional protection it is reasonable to install a
residual current device (RCD) with nominal operation
current not exceeding 30 mA, to install RCD, contact
a specialist.
EN
COFFEE MAKER BR1103
The co󰀨ee maker is intended for making espresso
or cappuccino co󰀨ee.
DESCRIPTION
1. Drip tray
2. Tray grid
3. Filter holder handle
4. Filter retainer
5. Filter holder
6. Co󰀨ee lter
7. Operation mode switch
8. Light indicator
9. Water tank lid
10. Cappuccinator pipe
11. Cappuccinator tip
12. Flask lid
13. Flask handle
14. Glass ask
15. Measuring spoon
1
14
13
12
2
3
4
5
6
7
8
9
10
11
15
Рiс. 1

4
EN
SAFETY MEASURES AND COFFEE MAKER
OPERATION RECOMMENDATIONS
Read the operation instructions carefully before
using the co󰀨ee maker and keep it for future
reference.
• Use the co󰀨ee maker for its intended purpose only,
as specied in this manual.
• Mishandling the co󰀨ee maker can lead to its
breakage and cause harm to the user or damage to
his/her property and it is not covered by warranty.
• The co󰀨ee maker is intended for making espresso
and cappuccino co󰀨ee and warming up ready drinks.
Do not warm any other liquids.
• Make sure that the operating voltage of the co󰀨ee
maker indicated on the label corresponds to your
home mains voltage.
• The power plug is equipped with a grounding contact,
plug it into the socket with reliable grounding contact.
In case of short circuit the grounding reduces the risk
of electric shock.
• Contact an electrical technician, if you are not
sure that your sockets are installed properly and
grounded.
• To prevent re do not use adapters designed for
connecting the power plug to the mains socket
without grounding contact.
• In case of sparking in the mains socket and
occurrence of smell of burning, unplug the unit and
apply to the organization maintaining your home
mains.
• If smoke appears from the unit body, unplug the unit
and take measures to prevent re spreading. Apply to
the service center for repairing the co󰀨ee maker.
• Always drain the remaining water from the water
tank. Do not store the co󰀨ee maker with the lled
water tank at temperature below 0°C.
• Do not use the co󰀨ee maker outdoors.
• It is not recommended to use the unit during lightning
storms.
• Protect the unit from impacts, falling, vibrations and
other mechanical stress.
• Never leave the plugged-in co󰀨ee maker unattended.
• To avoid re, electric shock or physical injuries, do
not immerse the power plug, the power cord or the
co󰀨ee maker body into water or any other liquids.
• Do not use the co󰀨ee maker in proximity to the
kitchen sink, in bathrooms, near swimming pools or
other containers lled with water.
• If the unit is dropped into water, unplug it
immediately, and only then you can take the unit out
of water.
• Do not use the co󰀨ee maker near heating appliances,
heat sources or open ame.
• Do not use the unit in places where aerosols are

5
EN
used or sprayed, and in proximity to inammable
liquids.
• Place the co󰀨ee maker on a at stable surface; do
not place it on the edge of a table. Do not let the
power cord hang from the edge of the table and
make sure it does not touch hot surfaces or sharp
edges of furniture.
• Do not place the co󰀨ee maker on hot surfaces.
• Do not touch the power cord and the power plug with
wet hands.
• Use only the co󰀨ee maker parts and accessories
supplied with the unit.
• Before switching the co󰀨ee maker on, make sure that
all removable parts are installed properly.
• Do not switch the co󰀨ee maker on if the water tank
is empty.
• Handle the glass co󰀨ee ask with care to avoid
damaging it!
• Do not use the ask for other purposes, do not place
it on electric and gas cookers and do not use the
ask in microwave ovens.
• Use the co󰀨ee maker only with the co󰀨ee ask
installed.
• Do not remove the ask during co󰀨ee making.
• Avoid sharp temperature di󰀨erence. Otherwise the
glass ask may crack.
• Do not put a hot glass ask on a cold surface.
• Do not use the co󰀨ee maker if the glass ask is
damaged.
• To avoid burns, do not touch hot surfaces of the
co󰀨ee maker during co󰀨ee making and right after
switching it o󰀨. Let the co󰀨ee maker cool down.
• Let the unit cool down completely before cleaning
and removing the accessories.
• Unplug the co󰀨ee maker before cleaning or when you
are not using it. When unplugging the co󰀨ee maker
hold only the power cord plug and carefully remove it
from the mains socket, do not pull the power cord —
this can lead to damage of the power cord or the
socket or cause short circuit.
• For children safety reasons do not leave polyethylene
bags, used as a packaging, unattended.
ATTENTION!
Do not allow children to play with polyethylene bags
or packaging lm. Danger of su󰀨ocation!
• The co󰀨ee maker is not intended for usage by
children.
• Do not leave children unattended to prevent using
the unit as a toy.
• Do not allow children to touch the unit and the power
cord during the co󰀨ee maker operation.
• Place the unit out of reach of children during the
operation and cooling down.
• This unit is not intended for usage by physically or
mentally disabled persons (including children) or by

6
EN
persons lacking experience or knowledge if they are
not under supervision of a person who is responsible
for their safety or if they are not instructed by this
person on the usage of the unit.
• From time to time check the power cord and the
power plug integrity.
• If the power cord is damaged, it should be replaced
by the manufacturer, a maintenance service or
similar qualied personnel to avoid danger.
• Do not repair the unit by yourself. Do not
disassemble the unit by yourself, if any malfunction
is detected, and after it was dropped, unplug the unit
and apply to the service center.
• Transport the co󰀨ee maker in the original package.
• Keep the unit out of reach of children and disabled
persons.
COFFEE MAKER IS INTENDED FOR HOUSEHOLD
USE ONLY, DO NOT USE THE COFFEE MAKER FOR
COMMERCIAL OR LABORATORY PURPOSES.
BEFORE USING THE COFFEE MAKER
After unit transportation or storage at low
temperature, it is necessary to keep it for at least
three hours at room temperature.
• Unpack the co󰀨ee maker and remove all the
packaging materials.
• Keep the original package.
• Read the safety measures and operating
recommendations.
• Check the delivery set.
• Examine the co󰀨ee maker for damages, in case of
damage do not plug it into the mains.
• Make sure that the specications of power supply
voltage specied on the lower panel of the unit
correspond to the specications of your mains.
• Wipe the surface of the co󰀨ee maker body with a
clean, slightly damp cloth to remove dust.
• Wash all removable parts in warm water with a
neutral detergent: the ask lid (12), the co󰀨ee ask
(14), the lter holder (5), the lter (6), the grid (2) and
the tray (1), rinse them and dry.
• Install the tray (1) and the grid (2) back to their
places.
• Make sure that the power plug is not inserted into the
mains socket, and the operation mode switch (7) is
set to the position « ».
• Remove the water tank lid (9) turning it
counterclockwise and ll the water tank, using the
ask (14). Do not exceed the maximal capacity of the
water tank.
• Install the lid (9) back to its place and thread it
rotating clockwise.
• Put the lter (6) into the holder (5), do not add ground
co󰀨ee into the lter (6).
• Set the lter holder (5) to the position « », the lter
holder (5) ledges should match the grooves in the

7
EN
boiler. Turn the lter holder (5) counterclockwise to
the position « » (pic. 1).
• Place the ask (14) on the grid (2).
• Insert the power plug into the mains socket.
• Set the operation mode switch (7) to the position «
brew », the light indicator (8) will light up, the heating
element will switch on and water will start pouring
into the ask (14) under pressure.
• After water pouring set the operation mode switch (7)
to the position « », and the indicator (8) will go out.
• Pour the water out of the ask (14).
• If necessary, repeat the washing cycle of the co󰀨ee
maker 2-3 times.
• To wash the cappuccinator pipe (10), remove the
water tank lid (9) by turning it counterclockwise
and pour some water into the tank using the ask
(14). Install the lid (9) back to its place and thread it
rotating clockwise until xed.
• Put the lter (6) into the holder (5), do not add ground
co󰀨ee into the lter (6).
• Set the lter holder (5) to the position « », turn the
lter holder (5) counterclockwise to the position «
» (pic. 1).
• Place the ask (14) under the cappuccinator pipe
(10) tip (11).
• Insert the power plug into the mains socket.
• Set the operation mode switch (7) to the position «
steam», the light indicator (8) will light up, the heating
element will switch on and steam under pressure will
be released into the ask (14).
• After steam release set the operation mode switch
(7) to the position « » to switch the co󰀨ee maker
o󰀨, and the indicator (8) will go out.
• The co󰀨ee maker is ready for usage.
MAKING ESPRESSO
Recommendations on making espresso
• Use ground co󰀨ee for espresso co󰀨ee makers or
freshly ground co󰀨ee beans.
• Slightly tamp the ground co󰀨ee in the lter (6) with
the back side of the measuring spoon (15).
• The taste of ready co󰀨ee depends on the quality and
grinding degree of co󰀨ee beans. If co󰀨ee is pouring
out too long, this means the co󰀨ee powder is too ne
or it is tamped too strongly.
ATTENTION!
- Do not remove the lter holder (5) during co󰀨ee
maker operation.
- When making co󰀨ee do not leave the operating
co󰀨ee maker unattended, as it is necessary to
watch the ask (14) being lled with ready co󰀨ee!

8
EN
• After making co󰀨ee set the operation mode switch (7)
to the position « » to switch the co󰀨ee maker o󰀨,
and the indicator (8) will go out.
• Pour the ready co󰀨ee into cups.
• Remove the lter holder (5) by turning it clockwise,
wash the lter (6). Use the lter retainer (4) to avoid
the lter (6) dropping.
• Control the tray (1) lling, when the tray (1) is full,
remove the grid (2) and the tray (1), pour the liquid out
of the tray (1). Wash the tray (1) and the grid (2), dry
them and install the tray (1) and the grid (2) back to
their places.
MAKING CAPPUCCINO
Attention! When making cappuccino be careful to avoid
getting burns by outgoing hot steam.
• Make co󰀨ee, as described in the chapter «MAKING
ESPRESSO», pour co󰀨ee in the cup with enough
capacity to add frothed milk.
• Milk for making foam must be cold, fresh and without
additives. Use whole milk with fat content from 4%
to 6%, the cream fat content should be not less than
10%.
• Set the operation mode switch (7) to the position «
» to switch the co󰀨ee maker o󰀨 and release the
pressure, then unplug the unit.
• Remove the water tank lid (9) turning it
counterclockwise and pour some water into the tank
• Make sure that the power plug is not inserted into the
mains socket, and the operation mode switch (7) is
set to the position « ».
• Remove the water tank lid (9) turning it
counterclockwise and ll the water tank, using the
ask (14). Do not exceed the maximal capacity of the
water tank.
Note: there are water level marks on the ask (14), the
maximal level mark is for 4 cups of co󰀨ee, the minimal
mark is for 2 cups of co󰀨ee.
• Install the lid (9) back to its place and thread it
rotating clockwise.
• Put the lter (6) into the holder (5), add ground co󰀨ee
into the lter (6) with the measuring spoon (15).
Note: there are marks on the lter (6) for the amount of
ground co󰀨ee for making 2 or 4 cups of co󰀨ee. Add the
required amount of ground co󰀨ee into the lter (6).
• Set the lter holder (5) to the position « », the lter
holder (5) ledges should match the grooves in the
boiler. Turn the lter holder (5) counterclockwise to
the position « » (pic. 1).
• Place the ask (14) on the grid (2).
• Insert the power plug into the mains socket.
• Set the operation mode switch (7) to the position «
brew », the light indicator (8) will light up, the heating
element will switch on and the ready co󰀨ee will start
pouring into the ask (14).

9
EN
using the ask (14). Install the lid (9) back to its place
and thread it rotating clockwise.
• Place a cup with cold milk or cream under the tip
(11).
• Switch the co󰀨ee maker on by setting the operation
mode switch (7) to the position «steam», the indicator (8)
will light up, the heating element will switch on and
the steam under pressure will be released from the
tip (11).
• Put the tip (11) into the cup with cold milk or cream.
• The tip (11) should not touch the bottom of the cup,
as this can prevent the steam release.
• The outgoing steam creates whirls which froth milk;
from time to time lift and lower the cup with milk or
cream against the tip (11) to make the milk foam.
Note: always put the tip (11) for approximately 1-2 cm
into milk or cream.
• If you cannot make frothed milk, don’t worry and
experiment until you achieve good results. Try
making frothed milk with the removed tip (11).
• Set the operation mode switch (7) to the position «
» to switch the co󰀨ee maker o󰀨 and to release the
pressure.
• Add frothed milk to the ready espresso, add sugar to
taste. You can decorate the frothed milk with cocoa
powder.
• After frothing the milk clean the cappuccinator pipe
(10) and wash the tip (11).
• Remove the tip (11), wash it under a warm water jet,
then dry it.
• Immerse the cappuccinator pipe (10) into a container
with water, switch the steam supply on by setting the
operation mode switch (7) to the position «steam». In
10-15 seconds set the operation mode switch (7) to
the position « » to switch the co󰀨ee maker o󰀨.
DESCALING
• For e󰀨ective operation of the co󰀨ee maker it is
necessary to clean (descale) the co󰀨ee maker from
mineral deposits every 2-3 months.
Note: to remove the scale you can use special
descaling agents for co󰀨ee makers and co󰀨ee
machines, strictly following the instructions on their
usage.
1. Make sure that the power plug is not inserted into
the mains socket, and the operation mode switch
(7) is set to the position « ».
2. Remove the water tank lid (9) turning it
counterclockwise and pour the descaling agent into
the water tank, using the ask (14). Do not exceed
the maximal capacity of the water tank.
3. Install the lid (9) back to its place and thread it
rotating clockwise.
4. Put the lter (6) into the holder (5), do not add
ground co󰀨ee into the lter (6).

10
EN
5. Set the lter holder (5) to the position « », the
lter holder (5) ledges should match the grooves in
the boiler. Turn the lter holder (5) counterclockwise
to the position « » (pic. 1).
6. Place the ask (14) on the grid (2).
7. Insert the power plug into the mains socket.
8. Set the operation mode switch (7) to the position «
brew », the light indicator (8) will light up, the heating
element will switch on and water will start pouring
into the ask (14) under pressure.
9. In 10-15 seconds set the operation mode switch
(7) to the position « », and the indicator (8) will
go out.
10. Place the ask (14) under the tip (11) and set the
operation mode switch (7) to the position «steam», in
5 seconds set the operation mode switch (7) to the
position « ».
11. Set the ask (14) on the grid (2), wait for 10-15
minutes and switch the water supply on by setting
the switch (7) to the position « brew », wait until the
cleaning agent release stops completely.
12. Set the operation mode switch (7) to the position «
» to switch the co󰀨ee maker o󰀨 and to release the
pressure. Unplug the unit, unscrew the lid (9) and
ll the tank with clean water. Insert the power plug
into the mains socket.
13. Set the ask (14) under the tip (11) and switch the
steam supply on «steam», in 15 seconds switch the
steam supply o󰀨 and place the ask (14) on the
grid (2). Switch the water supply on and wait until
the water release stops completely.
14. Set the operation mode switch (7) to the position «
» to switch the co󰀨ee maker o󰀨 and to release
the pressure.
• If necessary, repeat the washing of the co󰀨ee maker
2-3 times.
CLEANING AND CARE
• Always switch the co󰀨ee maker o󰀨 and unplug it
before cleaning.
• Let the co󰀨ee maker cool down completely and clean
the outer surfaces of the unit body with a soft, slightly
damp cloth, then wipe dry.
• Use soft detergents to remove dirt; do not use metal
brushes, abrasive detergents and solvents.
• Remove the water tank lid (9) by turning it
counterclockwise, turn the co󰀨ee maker upside down
and drain the remaining water from the water tank,
screw the lid (9).
• If the lter (6) openings are blocked with the ground
co󰀨ee, clean them with a small brush.
• Remove the grid (2) and the tray (1), pour the water
out, wash the tray (1) and the grid (2), rinse them and
dry. Install the tray (1) and the grid (2) back to their
places.