BRAYER BR1105 User manual

Instruction manual
Инструкция по эксплуатации
Espresso machine BR1105
Рожковая кофеварка BR1105
brayer.ru

СОДЕРЖАНИЕ
EN......................................................................................................................................3
DE....................................................................................................................................16
RU ...................................................................................................................................31
KZ....................................................................................................................................45

3
EN
ATTENTION!
For additional protection it is reasonable to install a
residual current device (RCD) with nominal operation
current not exceeding 30 mA, to install RCD, contact
a specialist.
EN
ESPRESSO MACHINE BR1105
The co󰀨ee maker is intended for making “espresso”
and “cappuccino” co󰀨ee.
DESCRIPTION
1. Drip tray
2. Drip tray grid
3. Tray lling pop-up indicator
4. Filter holder handle
5. Filter holder
6. Co󰀨ee lter
7. Control panel
8. Cup warming tray
9. Steam supply control knob « »
10. Cappuccinator pipe
11. Espresso machine body
12. Cappuccinator pipe tip
13. Water tank handle
14. Water tank lid
15. Removable water tank
16. Measuring spoon with ground co󰀨ee tamper
Control panel
17. Espresso machine on/o󰀨 button « »
18. One cup button « »
19. Steam supply on button « »
20. Two cups button « »
20
16
15
14
9
13
18
17
1
4
3
2
5
6
7
8
10
11
12
19

4
EN
SAFETY MEASURES AND COFFEE MAKER
OPERATION RECOMMENDATIONS
Read the operation instructions carefully before
using the co󰀨ee maker and keep it for future
reference.
• Use the co󰀨ee maker for its intended purpose only,
as specied in this manual.
• Mishandling the co󰀨ee maker can lead to its
breakage and cause harm to the user or damage to
his/her property and it is not covered by warranty.
• The co󰀨ee maker is intended for making espresso
and cappuccino co󰀨ee and warming up ready drinks.
Do not warm any other liquids.
• Make sure that the operating voltage of the co󰀨ee
maker indicated on the label corresponds to your
home mains voltage.
• The power plug is equipped with a grounding contact,
plug it into the socket with reliable grounding contact.
In case of short circuit the grounding reduces the risk
of electric shock.
• Contact an electrical technician, if you are not
sure that your sockets are installed properly and
grounded.
• To prevent re do not use adapters designed for
connecting the power plug to the mains socket
without grounding contact.
• In case of sparking in the mains socket and
occurrence of smell of burning, unplug the unit and
apply to the organization maintaining your home
mains.
• If smoke appears from the unit body, unplug the unit
and take measures to prevent re spreading.
• Use and store the co󰀨ee maker at the temperature
above 0 °C.
• Do not use the co󰀨ee maker outdoors.
• It is not recommended to use the unit during lightning
storms.
• Protect the unit from impacts, falling, vibrations and
other mechanical stress.
• Never leave the plugged-in co󰀨ee maker unattended.
• To avoid re, electric shock or physical injuries, do
not immerse the power plug, the power cord or the
co󰀨ee maker body into water or any other liquids.
• Do not use the co󰀨ee maker in proximity to the
kitchen sink, in bathrooms, near swimming pools or
other containers lled with water.
• If the unit is dropped into water, unplug it
immediately, and only then you can take the unit out
of water. Apply to the service center for testing or
repairing the unit.
• Do not use the co󰀨ee maker near heating appliances,
heat sources or open ame.
• Do not use the unit in places where aerosols are
used or sprayed, and in proximity to inammable
liquids.
• Place the co󰀨ee maker on a at stable surface; do
not place it on the edge of a table. Do not let the

5
EN
power cord hang from the edge of the table and
make sure it does not touch hot surfaces or sharp
edges of furniture.
• Do not place the co󰀨ee maker on hot surfaces.
• Do not touch the power cord and the power plug with
wet hands.
• Use only the co󰀨ee maker parts and accessories
supplied with the unit.
• Before switching the co󰀨ee maker on, make sure that
all removable parts are installed properly.
• Ensure that the water level in the water tank is not
below the minimal mark.
• Do not switch the co󰀨ee maker on if the water tank
is empty.
• To avoid getting burns by hot steam be careful when
frothing milk or warming the ready drinks.
• The lter holder surface, the cappuccinator pipe and
the cappuccinator tip can get rather hot. Be cautious
and careful when in contact with hot surfaces.
• Do not remove the lter holder during co󰀨ee maker
operation.
• Let the unit cool down completely before cleaning
and removing the accessories.
• Unplug the co󰀨ee maker before cleaning or when you
are not using it. When unplugging the co󰀨ee maker
hold only the power cord plug and carefully remove it
from the mains socket, do not pull the power cord —
this can lead to damage of the power cord or the
socket or cause short circuit.
• For children safety reasons do not leave polyethylene
bags, used as a packaging, unattended.
ATTENTION!
Do not allow children to play with polyethylene bags
or packaging lm. Danger of su󰀨ocation!
• The co󰀨ee maker is not intended for usage by
children.
• Do not leave children unattended to prevent using
the unit as a toy.
• Do not allow children to touch the unit and the power
cord during the co󰀨ee maker operation.
• Place the unit out of reach of children during the
operation and cooling down.
• This unit is not intended for usage by physically or
mentally disabled persons (including children) or by
persons lacking experience or knowledge if they are
not under supervision of a person who is responsible
for their safety or if they are not instructed by this
person on the usage of the unit.
• From time to time check the power cord and the
power plug integrity.
• If the power cord is damaged, it should be replaced
by the manufacturer, a maintenance service or
similar qualied personnel to avoid danger.
• Do not repair the unit by yourself. Do not
disassemble the unit by yourself, if any malfunction
is detected, and after it was dropped, unplug the unit

6
EN
and apply to the service center.
• Transport the co󰀨ee maker in the original package.
• Keep the unit out of reach of children and disabled
• persons.
COFFEE MAKER IS INTENDED FOR HOUSEHOLD
USE ONLY, DO NOT USE THE COFFEE MAKER FOR
COMMERCIAL OR LABORATORY PURPOSES.
BEFORE USING THE COFFEE MAKER
After unit transportation or storage at low
temperature, it is necessary to keep it for at least
three hours at room temperature.
• Unpack the co󰀨ee maker and remove all the
packaging materials.
• Keep the original package.
• Read the safety measures and operating
recommendations.
• Check the delivery set.
• Examine the co󰀨ee maker for damages, in case of
damage do not plug it into the mains.
• Make sure that the specications of power supply
voltage specied on the lower panel of the unit
correspond to the specications of your mains.
• Wipe the surface of the co󰀨ee maker body with a
clean, slightly damp cloth to remove dust.
• Make sure that the steam supply is closed. To do this
turn the knob (9) « » clockwise until bumping
«•».
• Before using the espresso machine for the rst time,
wash all removable parts (1, 2, 5, 6, 12, 15, 16) with
warm water and neutral detergent, rinse and dry
them.
• Remove the water tank (15), ll it with cold water up
to the MAX mark and install it back to its place.
Notes:
- to ll the water tank (15) with water you can open
the lid (14) and pour water into the tank (15).
-to carry the water tank (15), take it by the handle
(13).
• Install the co󰀨ee lter (6) (do not add ground co󰀨ee
into the lter) into the holder (5) having preliminary
matched the ledge on the lter (6) with the groove on
the holder (5) and turn the lter (6) counter/clockwise
to x the lter.
• Install the lter holder (5) into the co󰀨ee maker. The
holder (5) ledges should match the grooves on the
boiler «INSERT», after that turn the lter holder
handle (4) to the right until bumping «LOCK».
• Place a suitable cup on the grid (2).
• Insert the power plug into the mains socket.
Note: - the buttons on the control panel (7) are
sensory, you just need to touch the button to switch the
necessary operation mode on.
• Switch the espresso machine on by pressing the on/
o󰀨 button (17) « », the button (17) illumination
will light up, and the illumination of buttons (18,

7
EN
19, 20) will be ashing. When the buttons (18, 19,
20) illumination will glow constantly, it means that
preheating is nished.
Notes:
- when switching the unit for the rst time, the
buttons (18, 19, 20) illumination will be ashing
quickly, because the boiler is empty. Press the
two cups button (20) « », the pump will be
switched on and start injecting water into the
boiler, the buttons (18, 19, 20) illumination will stop
ashing and start glowing constantly;
- the rst switching on of the pump may be
accompanied by an uncharacteristic sound, this
is a normal. After lling the boiler with water, the
sound of the pump will return to normal.
• Wait until the buttons (18, 19, 20) illumination glows
constantly, then switch the water supply on by
pressing the button (20) « », the pump will switch
on for 25 seconds, pour the water out from the cup
and press the button (20) again « » to switch the
water supply on again. After switching the pump o󰀨,
pour the water out from the cup.
• Repeat this procedure several times, the boiler will
be clean after that.
• To switch the espresso machine o󰀨, press the on/
o󰀨 button (17) « », the buttons (17, 18, 19, 20)
illumination will go out.
AUTO SWITCH OFF FUNCTION
• If no actions were performed during 25 minutes
after switching on, the co󰀨ee maker will switch o󰀨
automatically.
HOW TO MAKE A GOOD ESPRESSO
• Use ground co󰀨ee for espresso co󰀨ee makers.
• Slightly tamp the ground co󰀨ee in the lter (6), you
can do it with the back side of the measuring spoon
(17).
• Co󰀨ee strength depends on the quality and grinding
degree of co󰀨ee beans. If co󰀨ee is pouring out too
long, this means the co󰀨ee powder is too ne or it is
tamped too strongly.
PREHEATING
• To make a cup of hot espresso, it is recommended to
preliminary heat up the co󰀨ee lter (6) and the lter
ATTENTION!
• Do not remove the lter holder (5) during espresso
machine operation.
• Do not remove the lter holder (5) immediately
after preparing co󰀨ee as there is redundant water
and steam pressure inside the lter (5), let the
co󰀨ee maker cool down completely.
• To remove the lter holder (5) turn the handle (4) to
the left «INSERT» and remove the lter holder (5).

8
EN
holder (5).
• Open the lid (14) and ll the tank (15) with water, or
remove the tank (15) and ll it with water, then install
the tank (15) back to its place.
• Install the co󰀨ee lter (6) into the holder (5) having
preliminary matched the ledge on the lter (6) with
the groove on the holder (5) and turn the lter (6)
counter/clockwise to x the lter.
• Install the lter holder (5) into the co󰀨ee maker. The
holder (5) ledges should match the grooves on the
boiler «INSERT », after that turn the lter holder
handle (4) to the right until bumping «LOCK».
• Place a suitable cup on the grid (2).
• Insert the power plug into the mains socket.
• Switch the espresso machine on by pressing the on/
o󰀨 button (17) « », the button (17) illumination
will light up, and the illumination of buttons (18,
19, 20) will be ashing. When the buttons (18, 19,
20) illumination will glow constantly, it means that
preheating is nished.
• Switch the water supply on by pressing the button
(20) « », the pump will switch on for 25 seconds
and hot water will be poured into the cup. After
switching the pump o󰀨, pour the water out from the
cup.Preheating is over.
MAKING ESPRESSO
AFTER PREHEATING:
• Make sure that the steam supply is closed. To do this
turn the knob (9) « » clockwise until bumping
«•».
• Remove the lter holder (5) by turning the handle (4)
to the left «INSERT» and remove the lter holder (5).
• Put ground co󰀨ee in the lter (6), slightly tamp the
ground co󰀨ee with the back side of the measuring
spoon (16).
• Install the lter holder (5) into the co󰀨ee maker. The
holder (5) ledges should match the grooves on the
boiler «INSERT», after that turn the lter holder handle
(4) to the right until bumping «LOCK».
• Wait until the buttons (18, 19, 20) illumination glows
constantly, the espresso machine is ready for
operation.
• Switch the water supply on by pressing the button
(18) « » to make one cup of co󰀨ee. The pump
will switch on and will be operating for 15 seconds.
The operation time of the pump 15 seconds is set by
default.
• To make two cups of co󰀨ee press the button (20) «
». The pump will switch on and will be operating
ATTENTION!
When making co󰀨ee do not leave the operating
co󰀨ee maker unattended, as it is necessary to watch
the cup being lled with ready co󰀨ee!

9
EN
for 25 seconds. The operation time of the pump 25
seconds is set by default.
Note: - watch the cup lling with the ready co󰀨ee, if
you need t switch the water supply o󰀨, press again the
button (18) « » or the button (20) « ».
• Switch the espresso machine o󰀨 by pressing the on/
o󰀨 button (17) « », the buttons (17, 18, 19, 20)
illumination will go out.
• Wait until the co󰀨ee maker cools down and remove
the lter holder (5) by turning the handle (4) to the left
«INSERT». Remove the ground co󰀨ee remnants and
wash the lter (6).
• For easy removing of the co󰀨ee remnants use the
retainer on the handle (4) to prevent the lter (6) from
falling o󰀨 the holder (5).
• Notes:
-the cups should be preliminary heated up, when
water heats up in the boiler, put the cups on the
tray (8).
- if you need to promptly remove the lter holder
(5), you have to reduce the pressure in the boiler,
switch the co󰀨ee maker o󰀨 by pressing the on/
o󰀨 button (17) « », place a suitable cup under
the tip (12) and slightly open the steam supply by
turning the knob (9) « » counterclockwise.
After the pressure in the boiler is released, you
can remove the lter holder (5).
ESPRESSO PORTION SETTING
-To enter the programming mode, press and hold
the one cup button (18) « » for 3 seconds, the
button (18) « » illumination will be ashing.
Press the button (18) « » again. After the
required amount of ready co󰀨ee is poured into the
cup, press the button (18) « » again to nish
setting. Maximum time of water supply for making
one cup of co󰀨ee is 45 seconds.
-To enter the programming mode, press and hold
the two cups button (20) « » for 3 seconds,
the button (20) « » illumination will be
ashing. Press the button (20) « » again. After
the required amount of ready co󰀨ee is poured into
the cup, press the button (20) « » again to
nish setting. Maximum time of water supply for
making two cups of co󰀨ee is 90 seconds.
Notes:
- if you have programmed the water supply time
for making one cup of co󰀨ee, then the water
supply time for making two cups of co󰀨ee will be
automatically set doubled;
- water supply time for two cups of co󰀨ee can be set
up to 90 seconds. If the water supply time for two
cups of co󰀨ee was set, then the water supply time
for making one cup of co󰀨ee will be automatically
set as half the time for making two cups of co󰀨ee.
RETURN TO THE FACTORY SETTINGS
• Switch the espresso machine on and wait until the

10
EN
• Make co󰀨ee, as described in the chapter «MAKING
ESPRESSO», in the cup with enough capacity to add
frothed milk.
• Make sure that the steam control knob (9) « »
is in the position «the steam supply is o󰀨 «•».
• Press the steam supply button (19) « » and
wait until the button (19) « » illumination glows
constantly. Place any suitable bowl under the tip (12)
for water. Carefully turn the steam supply knob (9)
« » counterclockwise for a quarter of a turn to
remove the condensed uid from the cappuccinator
pipe (10).
• After removing the condensed uid close the steam
supply by turning the knob (9) « » clockwise
until bumping «•».
Note: some water or steam may appear from the lter
holder (5), it is normal.
• Put the cappuccinator pipe tip (12) into a glass with
cold milk or cream, the amount of milk or cream
should be about 100 ml. Carefully turn the steam
supply control knob (9) « » counterclockwise for
a quarter of a turn or more. The tip (12) should not
touch the bottom of the glass, as this can hinder the
steam release; you can make thick frothed milk in
several seconds.
Note:
-to avoid splashing milk always immerse the tip
(12) deeper than 1 cm from the milk surface.
-to avoid splashing milk or cream, do not open the
steam supply with a sharp turn of the knob (9) «
», always turn the knob (9) « » carefully.
- when selecting a cup for milk or cream, keep
in mind that the frothed milk amount increases
approximately twice;
-during the operation in the steam supply mode
the button (19) « » illumination will be ashing
and glowing constantly; it means that the water
temperature in the boiler is maintained within the
set limits;
• The outgoing steam creates whirls which froths milk;
from time to time lift and lower the bowl with milk
against the tip (12) to make the milk foam.
• Making the milk foam is an art. You may not make it
at the rst try, don’t worry and experiment until you
espresso machine is preheated and the buttons (18,
19, 20) indicators glow constantly.
• After the preheating is nished, press and hold
simultaneously the buttons (19) « » and (20) «
» for 3 seconds, the buttons (19 and 20) illumination
will ash 3 times, and the espresso machine will
return to the factory settings.
MAKING CAPPUCCINO
ATTENTION!
Be careful to avoid burns by the released hot steam.