Brecknell 6030 Operator's manual

Model 6030
Counting Scale
User Instructions
AWT 35-501440
Issue AA

6030_u_en_501440.book
Brecknell is part of Avery Weigh-Tronix. Avery Weigh-Tronix is a trademark of the Illinois Tool Works group of companies whose ultimate
parent company is Illinois Tool Works Inc ("Illinois Tool Works"). Copyright © 2014 Illinois Tool Works. All rights reserved.
No part of this publication may be reproduced by making a facsimile copy, by the making of a copy in three dimensions of a two-dimensional
work and the making of a copy in two dimensions of a three-dimensional work, stored in any medium by electronic means, or transmitted in
any form or by any means, including electronic, mechanical, broadcasting, recording or otherwise without the prior written consent of the
copyright owner, under license, or as permitted by law.
This publication was correct at the time of going to print, however Avery Weigh-Tronix reserves the right to alter without notice the
specification, design, price or conditions of supply of any product or service at any time.

6030 Counting Scale User Instructions 3
Table of Contents
Chapter 1 General Information and Warnings ........................................................................................ 5
About this Manual ..............................................................................................................5
Text Conventions ........................................................................................................ 5
Special Messages ....................................................................................................... 5
Safe Handling of Equipment with Batteries ........................................................................ 6
Safety Guide ...................................................................................................................... 6
Routine Maintenance ......................................................................................................... 6
Training .............................................................................................................................. 7
Sharp Objects .................................................................................................................... 7
Chapter 2 Introduction .............................................................................................................................. 9
Specifications ..................................................................................................................... 9
Installing the Battery .......................................................................................................... 9
Front Panel ...................................................................................................................... 11
Display and Keys ............................................................................................................. 11
Scale Keys ................................................................................................................ 11
LCD Symbol Descriptions ......................................................................................... 12
Chapter 3 Operation ................................................................................................................................ 13
Simple Weighing .............................................................................................................. 13
Tare Function ................................................................................................................... 13
Unit Key Function ............................................................................................................. 13
Set Auto-off Time ............................................................................................................. 14

4 6030 Counting Scale User Instructions

6030 Counting Scale User Instructions 5
1 General Information and Warnings
1.1 About this Manual
This manual is divided into chapters by the chapter number and the large text at the top
of a page. Subsections are labeled as shown by the 1 and 1.1 headings shown above.
The names of the chapter and the next subsection level appear at the top of alternating
pages of the manual to remind you of where you are in the manual. The manual name
and page numbers appear at the bottom of the pages.
1.1.1 Text Conventions
Key names are shown in bold and reflect the case of the key being described. This
applies to hard keys and on screen or soft keys.
Displayed messages appear in bold italic type and reflect the case of the displayed
message.
1.1.2 Special Messages
Examples of special messages you will see in this manual are defined below. The
signal words have specific meanings to alert you to additional information or the relative
level of hazard.
CAUTION!
This is a Caution symbol.
Cautions give information about procedures that, if not observed, could result
in damage to equipment or corruption to and loss of data.
NOTE: This is a Note symbol. Notes give additional and important information, hints
and tips that help you to use your product.

6 6030 Counting Scale User Instructions
1.2 Safe Handling of Equipment with Batteries
1.3 Safety Guide
For the best performance and precise measurement
lDo NOT overload the scale. This will damage the loadcell and void the
warranty.
lDo NOT leave a load on the scale when not in use. This will decrease the
scale's accuracy and shorten the loadcell life.
lCheck the battery frequently. When the scale display flashes, charge the
battery with its dedicated charger.
lDo NOT attempt to repair the scale yourself. Contact your local
representative.
1.4 Routine Maintenance
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s instructions.
ATTENTION: Il y a danger d'explosion s'il y a remplacement incorrect de la
batterie, remplacer uniquement avec une batterie du même type ou d'un type
équivalent recommandé par le constructeur. Mettre au rebut les batteries
usagées conformément aux instructions du fabricant.
IMPORTANT: This equipment must be routinely checked for proper operation
and calibration.
Application and usage will determine the frequency of calibration required for
safe operation.

6030 Counting Scale User Instructions 7
1.5 Training
Do not attempt to operate or complete any procedure on a machine unless you have
received the appropriate training.
To avoid the risk of RSI (Repetitive Strain Injury), place the machine on a surface which
is ergonomically satisfactory to the user. Take frequent breaks during prolonged usage.
1.6 Sharp Objects
Do not use sharp objects such as screwdrivers or long fingernails to operate the keys.

6030 Counting Scale User Instructions 9
2 Introduction
2.1 Specifications
2.2 Installing the Battery
1. Turn the scale over to find the battery housing cover.
Model 6030
Capacity 5000g x 1g
Weigh Units g, lb
Dimensions 170 mm x 150 mm x 46.5 mm (7 in x 6 in x 2 in)
Platform Size 120 mm x 150 mm (5 in x 6 in)
Display 0.8 inch LCD display
Keys UNIT, ON/OFF, TARE/ZERO
Weight Net weight: 0.85 kg
Gross weight: 1.0 kg
Power 9V alkaline battery
9V adapter (male type)
Temperature Range 5°C up to +35°C
Battery housing cover

10 6030 Counting Scale User Instructions
2. Remove the two screws holding on the battery cover exposing the battery
cavity.
3. Install the 9V alkaline battery
4. Reinstall the battery housing cover.
Battery cavity

6030 Counting Scale User Instructions 11
2.3 Front Panel
2.4 Display and Keys
2.4.1 Scale Keys
Keys Key Name Function
ON/OFF Turn the scale ON or OFF
TARE/ZERO Tare an unwanted weight during the
weighing process
UNIT Select the weighing unit
0

12 6030 Counting Scale User Instructions
2.4.2 LCD Symbol Descriptions

6030 Counting Scale User Instructions 13
3 Operation
This section covers the various scale operations, such as simple weighing, tare, unit
switching and Auto-off feature.
3.1 Simple Weighing
1. Turn on the scale by pressing the ON/OFF key.
2. The display will count down from 88888 and will automatically display zero
(weighing mode).
3. Place the item in the middle of the scale. Wait until the scale stabilizes and
stable annunciator illuminates on the display.
3.2 Tare Function
Tare allows the user to zero the instrument to cancel the weight of a container from the
reading of the instrument, thus giving the true weight of the product being tested.
1. Turn on the scale by pressing the ON/OFF key.
2. When 0is displayed, place the object to be tared on the scale platform.
3. Press the TARE/ZERO key after the weight stabilizes and stable annunciator
appears on the display.
The display will return to 0.
4. Place the item to be weighed (without removing the tare object) on the scale.
The weighing result is the Net weight of the item.
To delete the saved tare value, remove the tare object from the scale platform and
press TARE/ZERO key.
3.3 Unit Key Function
Press the UNIT key to switch from one weighing unit to another. For example from g to
lb.
NOTE: The scale will automatically zero when turned on. If a value is displayed when
the platform is empty, press TARE to zero the display.
NOTE: If an Item is heavier than the scale capacity, the display will show the "Err"
prompt (= overload).

14 6030 Counting Scale User Instructions
3.4 Set Auto-off Time
The Model 6030 has an Auto-Off time option, which enables the scale to turn off
automatically when the scale is not in use. The time duration for auto-off can be
selected in the following way:
1. Turn on the scale by pressing the ON/OFF key.
2. Press the ZERO key for 3 seconds after the count down stops and LCD
displays zero.
SET P-13 and then A.off will be displayed.
3. Press the TARE key. The default auto-off time will be displayed.
4. Press the UNIT key to select the Auto-off time.
The Auto-off time can be set to 120/180/240/300 seconds.
Or
Auto-off option can be turned-off
1. To confirm press the TARE key again. For Example- If you want to select 240
seconds, press the TARE key when '240 S' is displayed.
2. Press the UNIT key.
End is displayed.
3. Press the TARE key to confirm.
NOTE: The AUTO-OFF option only works when the scale is using battery power. If
the scale is using an Adaptor, AUTO-OFF will be disabled automatically.

Brecknell
1000 Armstrong Dr., Fairmont, MN 56031
Toll free: 800-637-0529, Tel: [phone]
Fax: [phone]
Email: [e-mail]
www.brecknellscales.com
Brecknell
Foundry Lane
Smethwick, West Midlands B66 2LP
Tel: [phone]
Fax: [phone]
Email: [e-mail]
www.brecknellscales.co.uk