Brinkmann Home Security SL-7 User manual

MODEL SL-7 OWNER’S MANUAL
ASSEMBLY AND OPERATING INSTRUCTIONS
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 1

HOW YOUR HOME SECURITY MOTION
ACTIVATED LIGHTING SYSTEM WORKS
The Home Security Motion Activated Lighting
System is designed to turn on automatically
at night when a person enters the detection
zone. The light will stay on as long as the
motion detector senses motion in the zone.
The light will turn off in approximately 90
seconds after the person leaves the detection
zone or stops moving.
During the day, the solar panel converts
sunlight into electricity and recharges the
battery in the main housing. At night, the light
turns on automatically when it detects motion
using the electricity stored during that day.
The number of activations per night are
dependent on your geographical location,
weather conditions and seasonal lighting
availability.
Note: Solar security lights do not receive
as much direct sunlight in winter
months. Therefore, the number of
activations per night will be reduced
during winter.
BEFORE FIRST USE – After installing the
main housing and solar panel module,
leave the switch in the “OFF” position and
charge in full, direct sunlight for THREE
FULL DAYS. Then remove the switch label
and slide the switch to the “AUTO”
position. The light will turn on
automatically at night when it detects
motion.
Solar Panel
Detection Zone
1
Contains Lead-Acid (Pb) battery.
Battery must be recycled or
disposed of properly.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 2

PARTS LIST:
Home Security Main Housing
Main Housing Mounting Screws (2)
Solar Panel Module with Cord
Solar Panel Module Mounting Screws (3)
SL-7 Owner’s Manual
2
ASSEMBLY INSTRUCTIONS
Inspect contents of the box to ensure all parts are included and undamaged.
A Phillips screwdriver will be required.
1
2
3
4
5
Step 1
Select a location and attach the main housing
where you want to detect persons or objects
moving at night. Ideal places are patios, side
doors, garages and pool area. Mount the main
housing 6 to 8 feet above ground on a solid
surface for best motion detection and light
distribution.
Note: Do not place the main housing in high
traffic areas. Doing so will discharge the
battery quickly and unit will shut down
until it is recharged by the sun. Aim the
motion detector away from streets,
busy walk areas, trees and bushes.
Step 2
To attach the main housing, use the mounting
template in this manual to install the two main
housing mounting screws. The screw heads
must stand out from the surface by about
5/32”. This is about the thickness of two
quarters or two nickels.
3
4
1
2
Template on
back of manual
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 3

3
Step 3
Slide the two slots in the back of main
housing onto the screws.
Step 4
Select a location within 15 feet from the main
housing to mount the solar panel module. The
solar panel module must be mounted where it
will receive FULL, DIRECT SUNLIGHT for
several hours each day.
Step 5
Firmly plug the solar panel module cord into
the main housing.
Step 6
Mount the solar panel module in a sunny
location where it will receive FULL, DIRECT
SUNLIGHT for several hours each day.
Note: Shaded areas will not allow the solar
panel to fully charge the battery. This
will drastically reduce the number of
activations per night.
Step 7
Aim the solar panel toward the south, facing
upward at about 45° angle. The adjustable
base allows mounting on most vertical,
horizontal or sloping surface such as a wall,
post or roof. Excess cord can be tucked under
the base securely.
45°
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 4

4
Step 8
Point the two floodlights in the desired
direction. You may want to adjust the
floodlights after letting the unit operate for a
few nights.
Step 9
Position the detector head in the direction you
want to cover. Never aim the motion detector
head directly at the sun or above a 90° angle
(horizontal level). Do not rotate the head more
than 360°.
The motion detector covers an area of 130°
and a maximum range of approximately 75 feet
unless its view is blocked by a stationary
object such as a building or tree. The higher
the motion detector is mounted, the greater the
effective range. The motion detector is most
sensitive to persons or warm objects moving
across its detection zone, rather than toward or
away from it.
75 Feet
90°
Motion Detector Head
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 5

5
Step 1
After installing your light, leave the switch in the
“OFF” position and charge in FULL, DIRECT
SUNLIGHT for THREE FULL SUNNY DAYS.
Step 2
After allowing the battery to fully charge, the
motion detector can be adjusted and tested.
Point the motion detector head down 15° from
horizontal level.
Step 3
Move the slide switch to “TEST” position. Turn
the range knob all the way to the minimum
setting (counterclockwise). The lights will come
on for a few seconds, then turn off.
Step 4
Wait one minute for the circuit to stabilize, then
walk slowly across the detection zone. The lights
will turn on as soon as your presence is
detected. The lights will turn off in approximately
10 seconds after motion stops or you leave the
detection zone. Adjust the detector head up or
down, left or right, in small increments as
necessary. Increase the range by turning the
knob clockwise a little at a time and only if
necessary. Most applications work best at the
lower range setting.
Step 5
Place the switch to “AUTO” position. The lights
may come on for a few seconds. This is normal.
After dark, test your adjustment by walking
slowly across the detection zone. The lights will
turn on when your presence is detected and will
stay on as long there is motion in the detection
zone. The lights will turn off in approximately 90
seconds after you stop moving or leave the
detection zone. If additional adjustments are
required, it is recommended that they be made
in the test mode during the following day when
the switches are easily visible.
Note: Remember to switch to “TEST” for
daytime testing and switch back to
“AUTO” for nighttime operation. The
motion detector has a built-in photocell
sensor that prevents daytime operation
in the “AUTO” position.
TESTING INSTRUCTIONS
75 Feet
90°
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 6

6
Terminal
Wire Connector
Changing Batteries
1. Unscrew the four screws in front housing and
separate it from rear housing.
2. Carefully peel the tape off the battery, leaving
wires attached to tape.
3. Remove the battery from rear housing, being
careful not to pull on wires.
4. Disconnect wires from battery terminals and
remove battery.
5. Connect wires to new battery terminals. Make
sure red (+) wire is connected to red (+)
terminal and black (-) wire is connected to
black (-) terminal.
6. Place new battery in rear housing.
7. Attach tape and wires to front of battery.
8. Attach the front housing to rear housing using
the four screws that were removed in Step 1.
9. Place switch in the “OFF” position and charge
in FULL, DIRECT SUNLIGHT for THREE FULL
DAYS. Then slide the switch to the “AUTO”
position. The light will turn on automatically at
night when it detects motion.
IMPORTANT: The sealed battery in this product
contains lead and must be
recycled or disposed of properly.
For additional information
regarding disposal, contact your
local county solid waste authority.
1. Turn lens counterclockwise and remove.
2. Pull bulb straight out and replace with new
bulb. DO NOT PLACE NEW BULB IN BRASS
GROMMET HOLES.
3. Replace the lens by aligning the slots with the
grooves in the top housing and turning
clockwise to lock in place.
Changing Bulb
Lens
Bulb
Tape
Battery
Rear Housing
Front Housing
Contains Lead-Acid (Pb) battery.
Battery must be recycled or
disposed of properly.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 7

7
1. Clean snow and debris off the solar panel so the battery can recharge.
2. Check and replace battery periodically throughout the year, especially after
winter months.
Wintertime
Tips
Solar security lights can be left outside year round, even in cold weather.
However, if you wish to store your light indoors for more than two or three
days, follow these steps to prevent damage to battery:
1. Turn the switch to “OFF” position. Store at room temperature in a dry
area.
2. Never store unit with switch in “AUTO” or “TEST” position. This will
damage the battery and it will not recharge.
3. Store light and solar panel where it can receive some sunlight or room
light each day. The battery needs light to maintain a charge during
storage.
4. During prolonged storage, unit must be fully charged once every four
months. You may need to replace the battery after prolonged storage.
5. Never store the unit in a box or in a dark room without a source of light
on the solar panel or you may need to replace the battery before next use.
6. For best performance, do not store for prolonged periods.
Storage
Cleaning
It is important that the solar panel is kept free of dirt and debris. A dirty solar
panel will not allow the battery to fully charge. This will shorten the life of the
battery and cause the light to malfunction. Clean regularly with a dampened
cloth or paper towel.
If lights blink on and off:
• Direct lamps away from detector or reposition detector.
• Remove heat sources located near or under detector.
• Direct detector away from streets or active sidewalks.
If lights do not turn on at night:
• Switch is in the “OFF” Position. When the switch is in the “OFF” position,
light will not turn on after dark. Move switch to the “AUTO” position and
check for normal operation after dark.
• Make sure the solar panel module cord is plugged firmly into main
housing. The battery will not charge if this connection is loose.
• Battery is not fully charged or needs replacement:
a. Make sure light is located in an area where the solar panel gets the
maximum amount of full, direct sunlight every day.
Troubleshooting &
Important Information
Solar Panel
Module Cord
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 8

8
Note: After installing the main
housing and solar panel
module, leave the switch in
the “OFF” position and
charge in FULL, DIRECT
SUNLIGHT for THREE FULL
DAYS. Then remove the
switch label and slide the
switch to the “AUTO”
position. The light will turn
on automatically at night
when it detects motion.
Troubleshooting &
Important Information
(continued)
IMPORTANT: The sealed battery in
this product contains
lead and must be
recycled or disposed
of properly. For
additional
information
regarding disposal,
contact your local
county solid waste
authority.
b. If the weather has been cloudy or overcast during the day, the
battery will not be charged for operation at night. The light must
have direct sunlight every day to fully charge the battery. If the light
does not receive enough sunlight one day, it will recharge the next
sunny day and resume normal operation.
c. Check the battery on a voltage meter to ensure that battery is
charged to a full voltage of 6-volts. An electronics store will usually
check batteries at no charge. Battery should be replaced
periodically throughout the year, especially after winter months.
d. Diminishing light or gradual decrease in number of activations
indicate a dying battery that requires replacement. Replacement
battery may be purchased from The Brinkmann Corporation
Customer Service Department by calling 800-468-5252.
• Loose or burned out bulb. Bulbs can become loose over time. Check
and tighten the bulb periodically. If the bulb has burned out, a
replacement can be easily installed. Replacement bulbs may be
purchased from The Brinkmann Corporation Customer Service
Department by calling 800-468-5252.
• Dirty Solar Panel. A dirty solar panel will not allow the battery to fully
charge. This will shorten battery life. Clean regularly with a dampened
cloth or paper towel.
If lights come on randomly:
• Aim motion detector head lower.
• Cover areas which may be reflecting signals to motion sensor such as:
cooling or heating ducts, reflective surfaces, metal sheds, smooth walls
or windows, etc..
• Rotate the detector head right or left a few degrees.
• Mount your motion detector on a firm surface as vibrations can false
trigger the unit.
• Aim detector away from busy streets or sidewalks, trees and bushes.
If range is too short or too long:
• Position your motion detector so movement is across detection zone.
• Aim detector upward to increase range or downward to decrease range.
CAUTION: Do not use any other battery size or type. It will damage the
unit and void the warranty. Do not attempt to open the
detector housing. There are no user serviceable parts inside.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 9

cut along dotted line
TEMPLATE
Screw Hole
Screw Hole
9
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 10

10
HOME SECURITY ACCESSORIES
For Visa/MasterCard orders, please call 800-468-5252, Monday through Friday, 8:30 AM - 5:00 PM Central
Standard Time.
100-0057-0 Replacement Bulb
070-6001-0 SL-7 Replacement Battery
112-0010-0 15 ft. Extension Cord
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 11

For one year from date of purchase, The Brinkmann Corporation warrants the Home Security Motion Activated
Lighting System against defects due to workmanship or materials to the original purchaser. The Brinkmann
Corporation’s obligations under this warranty are limited to the following guidelines:
• This warranty does not extend to the bulb or batteries.
• This warranty does not cover solar security lights that have been altered/modified or damaged due to:
normal wear, abuse, improper maintenance and/or improper use.
• This warranty does not cover surface scratches or weathering as this is considered normal wear.
• Warranty service is limited to repair or replacement or solar security lights which prove defective under
normal use and which upon examination shall indicate to Brinkmann’s satisfaction, they are defective. If
Brinkmann confirms the defect and approves the claim, Brinkmann will elect to repair or replace the solar
security light as covered by the terms of this warranty.
• This warranty extends to the original purchaser only and is not transferable or assignable to subsequent
purchasers.
The Brinkmann Corporation requires reasonable proof of purchase. Therefore, we strongly recommend that
you retain your sales receipt or invoice. To obtain repair or replacement of your Home Security Motion
Activated Lighting System under the terms of this warranty, please call Customer Service Department at
800-527-0717 for a Return Authorization Number and further instructions. A receipt will be required. Solar
security lights returned to Brinkmann must include your name, address and telephone number. Please make
sure the light is properly packed, postage prepaid, and insured. A Return Authorization Number must be clearly
marked on the outside of the box. Brinkmann cannot be responsible for any solar security lights forwarded to
us without a Return Authorization Number.
EXCEPT AS ABOVE STATED, THE BRINKMANN CORPORATION MAKES NO OTHER EXPRESS WARRANTY.
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF PURCHASE. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU.
ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE FAILURE
OF THE HOME SECURITY MOTION ACTIVATED LIGHTING SYSTEM TO COMPLY WITH THIS WARRANTY OR
ANY IMPLIED WARRANTY IS EXCLUDED. CUSTOMER ACKNOWLEDGES THAT THE PURCHASE PRICE
CHARGED IS BASED UPON THE LIMITATIONS CONTAINED IN THE WARRANTY SET OUT ABOVE. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
ONE YEAR LIMITED WARRANTY
140-6007-0
2/96, 5/06
Owner’s Manual for Model
821-7000-0
© 1996 The Brinkmann Corporation
Dallas, TX 75244
www.brinkmann.net
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 12