Bristan JU BAS C User manual

AFTERCARE INSTRUCTIONS
Your fitting has a high quality finish and should be treated with care to preserve the
visible surfaces. All surface finishes will wear if not cleaned correctly, the only safe
way to clean your mixer is to wipe with a soft damp cloth. Stains can be removed
using washing up liquid. All bath cleaning powders and liquids will damage the
surface of your fitting -evennon-scratchcleaners.
GUARANTEE
All products are manufactured to the highest standards and a 5 year guarantee
covers any defect in manufacture.
NOTE: The 5 year guarantee on the valves is invalidated if damaged by any
waterborne debris.
In the interests of continuous product development we reserve the right to alter
specification as necessary
PRODUCT CODE: JU BAS C /JU BIDC
TELEPHONE HELP LINE: 0870 4425553
Bristan Group Ltd
Birch Coppice Business Park
Dordon
Tamworth
Staffordshire
B78 1SG
UK
Web Site: www.bristan.com
Telephone: [phone]
Facsimile: 0870 1611002
Email: [email protected]
(FI JU BASBID) (Rev. D2) (G)
Jute Basin/Bidet Mixer
Fitting Instructions
& Contents List
Please keep these instructions for future reference and for the
ordering of spare parts.
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

c
b
ed
a
1
23
45
6
7
8
9
10
11
12
13
14
WATERPRESSURE
This mixer is suitable for use at all supply pressures. However for optimum use,
both the hot and cold supplies should be reasonably balanced.
If the fitting is installed at low pressure (tank fed), then the minimum distance from
the outlet of the nozzle to the underside of the cold tank should be 2metres to
ensure adequate performance.
This mixer should be installed in compliance with Water Regulations. Where the
supplies are unbalanced, i.e. hot water from the cylinder tank / cold from the mains,
approved check valves must be fitted in the supply pipes.
For further details contact your Local Water Authority.
CONTENTS
1.MixerBody (x1)
2. OperatingRod (x1)
3.Rubber O-Ring (x1)
4.RubberC-Plate (x1)
5.MetalC-Plate (x1)
6.Copper Tail Pipes (x2)
7.ThreadedRod (x2)
8.Nut (x2)
9. Screw (x1)
10. Shaped Washer (x1)
11. Flat Washer (x1)
12. Waste Cap (x1)
13. WasteRod (x1)
14.RodConnector (x1)
a.Cartridge(x1)
b.Lock Nut (x1)
c. Shroud (x1)
d. Handle (x1)
e. Grub Screw (x1)
INSTALLATION
1.Identifyallcomponentsandcheckforcompleteness,particularlybeforearranging
fitting.
2. Install the mixer (1) into the basin.The nut (8) is used to secure the mixer to the
surface of basin using the threaded rod(7).
3. Connect the hot and cold water supplies.
4.Fit the pop up waste, with the flat washer (11)below and the shaped washer (10)
above the basin/bidet. It is recommended that a silicon sealant be applied to both
sealing faces of washers 10 and 11.The plugheight canbe setby adjusting the
wasterod (13) operating rod (2), rodconnector (14)and the screw (9) in the base of
the plug. Friction for the waste mechanism can be adjusted using the waste cap
(12).
5. Turn on the water supplies. Lift and turn handle both ways for a few minutes
letting the water flow,to check all joints and connections for leaks.
6. See over the page for aftercare instructions.
MAINTENANCE
If the fitting begins to drip:
1. Turn off the water supply.
2.Removegrub screw (e) and then remove handle (d) by pulling from cartridge (a).
Unscrew both shroud (c) and lock nut (b).
3.Removecartridge.Once removed, carefullyclean seating and all exposed parts.
4.Replace all of the abovethen turn on the water supply.
5. If problem persists contact ourhelpline quoting the product code.
Please Note:
In the unlikely event you find a part missing please contact our Customer Service
Help line on 08704425553or email [email protected] for immediate despatch
of part.
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk