Bristan Blitz Tap Series Wiring diagram

Please keep these instructions for future reference and request of replacement parts
Installation Instructions & User Guide
Blitz Tap Range

Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have
designed this product with your enjoyment in mind. To ensure that it works to its full
potential, it needs to be fitted correctly. These fitting instructions have been created to give
you all of the information you need and, if you need any further help, please do not hesitate
to give us a call on 0844 701 6273.
Important Safety Information 03
General Specifications 03
Dimensions 04-05
Installation Requirements 06
Installation 07-13
Basin & Bath Taps 07
Basin Mixer 08-09
Bath Filler 10-11
Bath Shower Mixer 12-13
Maintenance 14-16
Map of Hard Water Regions in the UK 17
Troubleshooting 18
Guarantee 19
Contents
02

Important Safety Information
• Please read these instructions thoroughly and retain for future use.
• All products manufactured and supplied by Bristan are safe provided they are installed
correctly, used correctly and receive regular maintenance in accordance with these
instructions.
•If you are in any doubt about your ability to install this product safely you must employ the
services of an experienced qualified plumber.
• Remove all packaging and check the components for damage before starting installation.
• Before starting any installation please consider the following: Prior to drilling into walls,
check that there are no hidden electrical wires, cables or water supply pipes. This can be
checked with the aid of an electronic detector.
• If power tools are used do not forget to: - Wear eye protection
- Unplug equipment after use
• This product must not be modified in any way as this will invalidate the guarantee.
• These fittings need to be installed in accordance with and meet the requirements of the Water
Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
General Specifications
Operating pressure range (bar) Min Max
Basin Taps 0.2 7.0
Bath Taps 0.2 7.0
Basin Mixer 0.2 7.0
Bath Shower Mixer 0.2 7.0
Bath Filler 0.2 7.0
Maximum static pressure – 10.0 bar
NOTE:- Nominally equal (balanced) inlet supply pressures are recommended for optimum
Performance of mixer taps.
Designed to comply with BS EN 200 for single taps / combination taps for water systems of type 1
and 2 general technical specifications; and to be used within systems designed to BS 6700.
BS 6700 recommends the temperature of stored water should never exceed 65°C. A stored water
temperature of 60°C is considered sufficient to meet all nominal requirements and will minimise
the build up of lime scale in hard water areas.
03

Dimensions
½" Basin Taps
Basin Mixer
04
¾" Bath Taps
54
Ø42
72
Ø32
54
86
110
G 1/2 G 3/4
50
60
Ø51
77
Ø38
62
90
12050

50
180
G¾"
Ø32
81
Bath Shower Mixer
Dimensions Cont.
05
Ø51
Ø38
202
7
Bath Filler
303
109
137
Ø30
79
180
50
G¾"
Ø32
81
Ø51
Ø38
202
7
303
109
137
Ø30
79
G½”
62 72

Installation Requirements
IMPORTANT - PLEASE READ
This/these fitting/fittings needs/need to be
installed in accordance with the following
Installation Requirements and Notes (IRN)
to ensure they meet the requirements of
the Water Supply (Water Fittings)
Regulations 1999 and the Scottish Byelaws
2004.
IRN R001 - BTZ ½ C, BTZ ¾ C, BTZ BAS C,
BTZ BF C, BTZ BSM C
See text of entry for Installation
Requirements or Notes.
IRN R005 – BTZ BF C, BTZ BSM C
This tap or combination tap assembly has a
Type AUK2 air gap and is therefore only
suitable for installation in domestic premises
or in other premises to protect against a
backflow risk up to a Fluid Category 3, unless
additional backflow protection for the higher
risk is included in the installation.
IRN R006 – BTZ ½ C, BTZ ¾ C, BTZ BAS C
This tap or combination tap is installed so
that its base is no lower than the spillover
level of the receiving vessel (for example, a
sink or washbasin), a Type AUK3 air gap is
achieved which permits installation of the tap
in any premises where backflow protection up
to Fluid Category 5 is required at the tap.
IRN R010 – BTZ BAS C, BTZ BF C -
Schedule 2-15 (1)
Water supplies shall be a reasonably
balanced pressures from a common source
(e.g. hot and cold supplies both from the
same storage or both from a supply pipe).
Where the fitting is supplied from unbalanced
supplies (e.g. hot and cold supplies from
separate sources) a ‘Listed’ single check
valve or some other no less effective backflow
prevention device shall be fitted immediately
upstream of both hot and cold water inlets.
IRN R030 – BTZ BSM C - Schedule 2-15
(1) Multiple inlet fittings installed in
domestic premises or in other premises to
protect against a backflow risk up to a Fluid
Category 3, incorporating a self cancelling
diverter acceptable as a backflow prevention
device (HC) and having an AUK2 or AUK3 air
gap, shall be installed in accordance with
IRN R010.
Multiple inlet fittings installed in premises
other than domestic to protect against a
backflow risk up to a Fluid Category 5,
incorporating a self cancelling diverter
acceptable as a backflow prevention device
(HC only) and having an AUK2 or AUK3 air
gap, shall be installed in accordance with
IRN R010. Alternatively the fitting shall be
supplied in accordance with IRN R040 unless
the shower head is constrained above the
spill-over lever of the bath, wash basin or
shower tray.
06

Installation
½" Basin & ¾" Bath Taps
1. Identify all components are present prior to starting installation.
2. Slide the plinth (6) and washer (7) onto the threaded tail and install the taps to the basin.
3. Using the washer (8) and backnuts (9) secure the taps to the basin by tightening the
backnuts onto the threaded tails. A suitable spanner may be required to fully tighten the
backnuts (9).
4. Connect the hot and cold water supplies to the taps.
5. Turn on the water supplies and open both taps letting the
water flow for a few minutes to check all joints and
connections for any leaks.
2
1. Handle x2
2. Handle Lever x2
3. Valve x2
4. Tap Body x2
5. Flow Straightener x2
6. Plinth x2
7. Washer x2
8. Washer x2
9. Backnut x2
10. Cap x2
11. Grub Screw x2
3
7
07
1
4
5
6
8
9
10 11

Installation cont.
Basin Mixer
1. Identify all components are present prior to starting installation using the diagram
overleaf.
2. Fit the mixer body (8) to the basin ensuring the plinth (9) and washer (10) are fitted
between the basin and the mixer body (8).
3. Make Sure that the threaded insert (11) is screwed fully into the mixer body (8)
4. Fit the rubber washer (12) and the ‘C’ shaped metal washer (13) to the underside of the
basin; and screw the brass ‘C’ shaped fixing (14) with the 2 small screws fitted on to the
bottom of the threaded insert (11) as tight as possible by hand.
5. Tighten the 2 small screws on the brass ‘C’ shaped fixing (14) using a suitable
screwdriver to secure the basin mixer into place, on the basin.
6. Screw in the flexible connecting pipes (17) to the mixer (DO NOT OVERTIGHTEN) and
connect the hot and cold water supplies.
7. Fit the clicker waste (15) to the basin ensuring a rubber washer is fitted between the
basin and the waste. Use a pure silicon sealant where necessary. Place the other rubber
washer under the basin and secure in place by tightening the backnut. In order to fill the
basin, the button in the middle of the waste needs to be pressed down. To release the
water, press the button again.
8. Lift the handle up and turn in both directions, letting the water flow for a few minutes to
check all joints and connections for any leaks.
1. Handle x1 10. Rubber Washer x1
2. Handle Lever x1 11. Threaded Insert x1
3. Cap x1 12. Rubber Washer x1
4. Grub Screw x1 13. ‘C’ Shaped Metal Washer x1
5. Shroud x1 14. ‘C’ Shaped Metal Fixing x1
6. Cartridge Retaining Nut x1 15. Clicker Waste x1
7. Cartridge x1 16. Flow Straightener x1
8. Mixer Body x1 17. Flexible Connecting Pipes x2
9. Plinth x1
08

6
Installation cont.
Basin Mixer
09
15
16
3
7
5
8
9
10
11
12
2
1
17
4
13
14

Installation cont.
Bath Filler
1. Identify all components are present prior to starting installation.
2. Slide the Plinth (6) and washer (7) onto the threaded tail of the tap and install the mixer
body (5) to the bath.
3. Using washers (8) and the backnuts (9) secure the mixer body (5) to the bath by tightening
the backnuts (9) onto the threaded tails (a suitable spanner maybe needed to fully tighten
the backnuts (9).
4. Connect the hot and cold water supplies using ¾" tap connectors (not supplied).
5. Turn the handles in both directions, letting the water flow for a few
minutes to check all joints and connections for leaks.
1. Handle x2 7. Washer x2
2. Handle Lever x2 8. Backnut x2
3. Valve x2 9. Anit Splash x2
4. Mixer Body x1 10. Grub Screw x2
5. Plinth x2 11. Cap x2
6. Washer X2
10