Bristan VAL2 BRDSM C CD Wiring diagram

Pack Contents
Installation Instructions
& User Guide
Specifications
Maximum Inlet Water Temperature
Inlet Connections
Dynamic Water Pressure
Tools You’ll Need
Prior to Installation
Crosshead Screwdriver Flat Screwdriver Pipe Cutter Adjustable Spanner
Please leave these instructions
with the end user
Product Code: VAL2 BRDSM C CD (D2)
All products manufactured and supplied by Bristan are safe
provided they are installed, used correctly and receive regular
maintenance in accordance with these instructions.
This product has been tested to the Water Regulations Advisory
Scheme (WRAS) and satisfies the requirements of the Water
Supply (Water Fittings) Regulations 1999 and current bylaws.
For full Installation Requirements & Notes (IRN)
please visit wras.co.uk/directory.
We recommend isolation valves to be fitted to the inlet water
supplies to ensure ease of future maintenance.
Before installing these taps the water supply must be thoroughly
flushed in order to remove any swarf, solder etc.
This product must not be modified in any way as this will
invalidate the guarantee.
60-65°C
recommended
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your product.
Spare Parts
1.0
5.0
Pressure
BAR
0.2
4.0
2.0 3.0
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0
Maximum Static Pressure: 10.0 bar 1/2”BSP
Min: 0.2 bar Max: 5.0 bar
3
4
5
2
1
REMEMBER
Hot on the
left, cold on
the right!
Secure the taps to the sink by
using the washer and metal
backnut below the sink.
Installation
Connect the hot and
cold water supplies to
the threaded tails.
Choose your desired leg position for the correct inlet centres.
Screw the legs to the tap
body, ensuring the top
washers and lower o’ring
are in place.
Screw the plinths on
to the tap legs.
Place the washers over
tap holes and feed the tap
through the holes
IMPORTANT
Turn on water
supply for a few
minutes and check
all joints and
connections for
any leaks .
160mm 200mm 240mm
x1
x2
x2
x2
x2
x2
x2
x2

At Bristan, we want to make things as easy as possible for our customers.
That’s why we oer solid guarantees on all our products, eective from the date of purchase,
to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register to register your product via a computer.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
3
2
1
Maintenance - Cleaning/Replacing Valves
Remove the
valves.
Remove
indice and
screw
IMPORTANT
Isolate
the water
supply before
starting!
Place valves in a suitable
solution and soak until
fully de-scaled.
4
Reverse the
maintenance
steps to replace
the handles.
12
3
You may need to use
adjustable spanner Troubleshooting
Symptom Cause Remedy
No flow or
low flow
rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on
and o as flow rate or pressure is too
low.
Increase water flow rate or pressure through system.
Head of water is below the
minimum distance required.
Refer to specification for minimum distance required.
Hot or cold water being drawn o
elsewhere causing pressure changes or
instantaneous boiler temperature
changes.
Do not use other water outlets when using the taps.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of debris
and any airlocks.
Water
dripping
from taps
This is normal for a short time after using
the taps.
This is caused by residual water tension, the build up
of water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves
Remove valves and clean, refer to 'Maintenance'
section before starting any maintenance.
Taps do not
turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
Love Your Chrome Bristan oers an eective chrome-friendly cleaning kit
for use with your taps and showers. Scan the QR Code
or search for ‘CLEAN KIT01’ on www.bristan.com.
General Cleaning
Bristan products are made from premium
materials, with hand polishing and
electroplated finishes.
Your taps or shower should be regularly cleaned
with warm water, a mild pH-neutral liquid soap,
and polished with a soft cloth. Any residues from
soap, toothpaste,
shampoos and shower gels can cause blemishes if
not rinsed o straight after use.
Household bleaches and cleaners contain harsh
chemicals and may damage the surface finish.
Avoid using abrasive cloths, scouring pads, scrub
sponges, steel wool
or anything similar.
Some surfaces such as nickel and pewter may be
aected by the dye found in some cloths, so it is
also important to avoid
hanging cloths on spouts.
On
On
Hot Cold
360°Swivel
Operation 3
Reverse the steps to
replace the spout.
123
2
1
Gently remove the
seals from the spout.
Inspect any for
damage and replace
if necessary.
Undo the screw at the back
of the spout to remove.
Maintenance - Spout Seals
IMPORTANT
Isolate the
water supply
before
starting!