Bristan Palermo PA BSM C User manual

SAFETY
NOTE !
AFTERCARE INSTRUCTIONS
Your fitting has a high quality finish and should be treated with care
to preserve the visible surfaces.All surface finishes will wear if not
cleaned correctly, the only safe way to clean your mixer is to wipe
with a soft damp cloth. Stains can be removed using washing up
liquid. All bath cleaning powders and liquids will damage the surface
of your fitting even the non scratch cleaners.
GUARANTEE
All products are manufactured to the highest standards and a 5 year
guarantee covers any defect in manufacture. As gold and special
effect finishes are softer than chromium plate, special care must be
taken whencleaning; a 3 year guarantee covers these finishes.
NOTE: The 5 year guarantee on the valves is invalidated if damaged
by any waterborne debris.
In the interests of continuous product development we reserve the
right to alter specification as necessary.
PRODUCT CODE: PA BSM C
TELEPHONE HELPLINE:0844 701 6273
Bristan Group Ltd
Birch Coppice Business Park
Dordon
Tamworth
Staffordshire
B78 1SG
UK
A Masco Company
Web Site: www.bristan.com
Telephone: [phone]
Facsimile: 0844 701 6275
Email: [email protected]
(FI PA BSM)(R3)(U)
Palermo
Bath Shower Mixer
Before starting any installation project, consider
“safety” first. Look for the “safety note” sign and
follow this safety advice.
Prior to drilling into walls, check there are no hidden
electrical wires, cables or water supply pipes with
the aid of an electronic detector. If you use power
tools do not forget to:
-Wear eye protection
-Unplug equipment after use
Fitting Instructions
& Contents List
Please keep these instructions for future reference and
request of replacement parts.
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

180 mm
43
1
2
5
SAFETY
NOTE!
WATER PRESSURE
This mixer is suitable for high-pressure plumbing systems only with
minimum pressure of 1 bar. However for optimum use both the hot
and cold supplies should be reasonably balanced.
This mixer should be installed in compliance with Water Regulations.
Where the supplies are unbalanced, i.e. hot water from cylinder
tank/cold from the mains, approved check valves must be fitted in the
supply pipes. For further details contact your Local Water Authority.
Please Note:In the unlikely event you find a part missing please
contact our Customer Service Help line on 0844 701 6273 for
immediate dispatch of part.
INSTALLATION
1. Identify all components and check for completeness, particularly
before arranging fitting.
2. Fit the mixer body (1) to the bath using the backnuts (2) below and
the washers (3) above the bath, then connect the hot and cold water
supplies.
3. Fit the hose (4) to the mixer and the handset using the small
sealing(5)washers.
4. To fit wall bracket, position, mark out and drill holes to suit,
then screw wall bracket to the wall, ensuring that the
handset will reach it.
5. Fully open the mixer in the mid position, letting it run for a few
minutes and check all joints and connections for leaks.
6. Operate the mixer in both bath and shower mode.
To switch from bath to shower mode pull the diverter up. After use
the mixer automatically reverts to the bath-filling mode.
7. See over the page for aftercare instructions.
MAINTENANCE
If the fitting begins to drip:
1. Isolate water supplies.
2. Prise out handle cap (at back of handle), loosen grub screw and lift
off the handle.
3. Unscrew the shroud and brass retaining plate and lift out the
cartridge complete with seal.
4. Clean or replace cartridge, clean and grease seal and refit.
Note:that there are locating pins on the bottom of the cartridge that
fit in holes inside the tap, to ensure it is fitted the right way round.
5. Refit the handle and tighten the grub screw. Replace the handle
cap.
6. If problem persists contact our helpline quoting the product code.
CONTENTS:
1. Body (x1)
2. Backnut (x2)
3. Washer (x2)
4. Hose (x1)
5. Sealingwasher (x2)
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk