Bristan Z 1/2 C User manual

Fitting Instructions & Contents List
Fitting Instructions & Contents ListFitting Instructions & Contents List
Fitting Instructions & Contents List
Self
Self Self
Self –
––
– Closing Tap
Closing TapClosing Tap
Closing Tap
Please keep these instructions for future reference and request of replacement parts
Please keep these instructions for future reference and request of replacement partsPlease keep these instructions for future reference and request of replacement parts
Please keep these instructions for future reference and request of replacement parts
www.divapor.com

Contents
Contents Contents
Contents Page
PagePage
Page
1. Introduction 03
2. Safety Note 03
3. Specification 04
4. Installation 05 - 08
5. Cleaning & aintenance 09
Notes 10
6. Bristan Guarantee 11
www.divapor.com

1. Introduction
1. Introduction1. Introduction
1. Introduction
Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have designed this product with
your enjoyment in mind. To ensure that it works to its full potential, it needs to be fitted correctly. These fitting
instructions have been created to give you all of the information you need and, if you need any further help, please
do not hesitate to give us a call on 0844 701 6273.
. Safety Note
. Safety Note. Safety Note
. Safety Note
Please read these instruction thoroughly and retain for future use.
All product manufactured and supplied by Bristan are safe provided they are installed correctly, used correctly and
receive regular maintenance in accordance with these instructions.
These fittings need to be installed in accordance with and meet the requirements of the Water Supply (Water
Fittings) Regulations 1999 and Scottish Byelaws 2004.
Before starting any installation please consider the following:
Prior to drilling into walls, check that there are no hidden electrical
wires, cables or water supply pipes. This can be checked with the aid of
an electronic detector.
If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
SAFETY
NOTE
03
www.divapor.com

3. Specification
3. Specification3. Specification
3. Specification
Operating pressure range (bar) in. ax.
Z ½ C 0.2 3.0
Z BIB C 0.2 3.0
Z L ½ C 0.2 3.0
Designed to comply with BS EN 816 Sanitary tapware Automatic Shut Off Valves and to be used within systems
designed to BS 6700.
BS 6700 recommends the temperature of stored water should never exceed 65°C. A stored water temperature of
60°C is considered sufficient to meet all nominal requirements and will minimise the build up of lime scale in hard
water areas.
Z ½ C
Z ½ CZ ½ C
Z ½ C Z BIB C
Z BIB CZ BIB C
Z BIB C
04
Z L ½ C
Z L ½ CZ L ½ C
Z L ½ C
www.divapor.com

4. Installation
4. Installation4. Installation
4. Installation
If the fitting is installed at low pressure (tank fed), then the minimum distance from the highest installed position of
the outlet to the underside of the cold water tank should be at least 2 metres to ensure adequate performance.
Operating pressures: in 0.2 bar, ax 3.0 bar
Operating pressures: in 0.2 bar, ax 3.0 barOperating pressures: in 0.2 bar, ax 3.0 bar
Operating pressures: in 0.2 bar, ax 3.0 bar
1. Identify all components are present prior to installation.
2. Assemble and fix the tap as shown in the relevant diagram.
NOTE:- If the supply pressure is above 1.0 bar it may be advisable to fit the 6 or 8 litre per minute flow regulator.
The flow limiter should be fitted to the tail of the tap with the arrow pointing upwards and the ‘o’ ring at the base.
3. Connect the water supply to the tap.
4. The tap is supplied with both red and blue indices, for either hot or cold use. Please ensure that the correct
indice is fitted to the correct tap.
5. Turn the water supplies on and operate the tap several times to flush the system.
6. Check all joints and connections for leaks.
Note:- If the supply pressure is above 3 bar a pressure reducing valve must be fitted. All supply pipework should be
thoroughly flushed before connecting to the taps to remove any debris in the pipework. Taps should also be
installed without using of any sealants. Waterborne debris may damage internal parts. Damage caused by
waterborne debris will invalidate the guarantee.
05
Indice
Flow Regulator
www.divapor.com

Installation continued
Installation continued Installation continued
Installation continued –
––
– Z ½ C (Non Concussive Basin Taps)
Z ½ C (Non Concussive Basin Taps)Z ½ C (Non Concussive Basin Taps)
Z ½ C (Non Concussive Basin Taps)
1
6
06
5
4
3
2
Parts contents list
Parts contents listParts contents list
Parts contents list
1. Indices (pair) x 1
2. Flow regulator x 2
3. Backnut x 2
4. Washer x 2
5. Anti splash x 2
6. Self closing valve x 2
www.divapor.com

Installation continued
Installation continued Installation continued
Installation continued –
––
– Z BIB C (Non Concussive Bib Taps)
Z BIB C (Non Concussive Bib Taps)Z BIB C (Non Concussive Bib Taps)
Z BIB C (Non Concussive Bib Taps)
1
2
3
4
5
Parts contents list
Parts contents listParts contents list
Parts contents list
1. Cover plate x 1
2. Body x 1
3. Flow regulator x 1
4. Handle and valve complete x 1
5. Indice x 1
07
2
www.divapor.com

Installation continued
Installation continued Installation continued
Installation continued –
––
– Z L ½ C (Non Concussive Lever Basin Taps)
Z L ½ C (Non Concussive Lever Basin Taps)Z L ½ C (Non Concussive Lever Basin Taps)
Z L ½ C (Non Concussive Lever Basin Taps)
Parts contents list
Parts contents listParts contents list
Parts contents list
1. Self closing valve x 1
2. Flow regulator x 1
1
08
2
www.divapor.com

5. Cleaning & Maintenance
5. Cleaning & Maintenance5. Cleaning & Maintenance
5. Cleaning & Maintenance
Your fitting has a high quality finish and should be treated with care to preserve the visible surfaces.
All finishes will wear if not cleaned correctly. The only safe way to clean your product is to wipe with a soft damp
cloth. Stains can be removed using washing up liquid. All bathroom cleaning product (powders and liquids) will
damage the surface of your fitting, even the non-scratch cleaners.
NOTE:- Never use abrasive detergents or disinfectants or those containing alcohol, hydrochloric or phosphoric
acid.
We advise that your fitting is regularly serviced, particularly in hard water areas.
Traditional type valves: if the fitting leaks from the spindle.
1. Remove fitting handle (if necessary).
2. Tighten the gland nut on top of the valve.
All valve types- if the fitting begins to drip:-
1. Turn off the water supplies.
2. Remove fitting handle and valve.
3. Carefully clean the valve seating and rubber washer.
4. Replace valve and then turn on the water supplies.
5. If the problem persists contact our helpline quoting the product code overleaf.
Bristan recommend E-Cloth for cleaning all of our bathroom & kitchen products.
Using just water, E-cloth gives a smear free, deep clean by breaking up and
holding dirt, which normal cloths leave behind. Order through your Bristan
stockist.
(ORDER CODE: ECLOTH)
09
www.divapor.com

Notes
Notes Notes
Notes
10
www.divapor.com