Bristan GLL FLEXSNK C (D1) Wiring diagram

Installation Instructions
& User Guide
Please leave these instructions
with the end user
Product Code: GLL FLEXSNK C (D1)
1.0
5.0
Pressure
BAR
0.2
4.0
2.0 3.0
Specifications
Maximum Static Pressure: 10.0 bar
Inlet Water Temperature Inlet Connections
Min: 2.0 bar Max: 5.0 bar
Dynamic Water Pressure
5°C
25°C
Cold Water Supply
Min: 5°C Max: 25°C 65°C
Recommended
Servicing Your Tap
We recommend servicing your tap at
least once every year to prolong its life.
To see a video showing how to remove
the cartridge for servicing, scan the QR
code with your smart phone or tablet.
1/2” BSP
Flexible
Tails
Tools You’ll Need
Alternatively visit www.bristan.com/howto
Prior to Installation
Hot Water Supply
Pack Contents
65°C
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0
All products manufactured and supplied by Bristan are safe provided
they are installed, used correctly and recieve regular maintenance in
accordance with these instructions.
This product has been tested to the Water Regulations Advisory
Scheme (WRAS) and satisfies the requirements of the Water Supply
(Water Fittings) Regulations 1999 and current bylaws.
For full Installation Requirements & Notes (IRN) please visit
wras.co.uk/directory.
Isolation valves must be fitted to the inlet water supplies to ensure ease
of future maintenance.
Before installing these taps the water supply must be thoroughly
flushed in order to remove any swarf, solder etc.
This product must not be modified in any way as this will invalidate the
guarantee.
Feed the pipes
through the sink
hole and place
the tap body.
1
Put the plinth over
the top of the sink
hole, ensuring the
O-Ring, is underneath
Push the washers
against the tap body
and tighten with the
fixing nut.
2
Olive
Connect the
hot and cold
water connections.
Compression
Nut
Flexible Connecting Pipes
Spare Parts
5
Flexible
Spout
Spray
Handset
Continuous Flow
Press for
Spray
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your product.
4
x1
Adjustable Spanner Pipe Cutter
x1
x1
Installation
Hexagonal Key
3
Slight
bend
90°
angle
Kinks
Curved
round Twists
Spout Features
Cold
O
Hot
On
Operation
Switch on the water
supply and check
connections for any leaks.
Your tap is now ready to
use.
IMPORTANT
fit isolation
valves for
future
maintenance
REMEMBER
hot on the
left, cold on
the right
Marked red
for hot

Troubleshooting
Symptom Cause(s) Remedy
No flow or low
flow rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on and o as flow
rate or pressure is too low.
Increase water flow rate or
pressure through system.
Head of water is below the minimum distance required. Check the site has the required working
pressures according to the specification.
Hot or cold water being drawn o elsewhere causing
pressure changes or instantaneous boiler temperature
changes.
Do not use other water outlets when using the
taps.
Airlock or partial blockage in the supply pipework or
hoses.
Flush through pipework to ensure removal of
debris and any airlocks.
Water supply failure Investigate water supply. Check your plumbing
and heating systems for any faults.
Hose is leaking due to aging/damaged O-Rings or
Anti-Friction seals Call Customer Services for replacement seals
Water
dripping from
taps
This is normal for a short time after using the taps. This is caused by residual water tension,
the build up of water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves/cartridge
Remove valves/cartridge and clean, refer to
'Maintenance' section before starting any
maintenance.
Taps do not
turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
Handset
Pressure
Changes
Site water pressure is too high for the working
pressures listed on the specification.
Install a Pressure Reducing Valve in order to
achieve working levels of pressure.
Your fitting has a high quality finish and should be treated with care to preserve the visible surfaces.
All surfaces will wear if not cleaned correctly, the only safe way to clean your mixer tap is to wipe with a
soft damp cloth. Stains can be removed using washing up liquid. All bath cleaning powders and liquids
will damage the surface of your fitting, even the non-scratch cleaners.
Note: Never use abrasive detergents or disinfectants or those containing alcohol,
hydrochloric acid or phosphoric acid.
General Cleaning
Please use this space for any notes you or your installer may have
regarding the installation/plumbing of this product.
Maintenance - Cleaning/Replacing Cartridge
123
4Turn on the
mains water
supply, letting the
water flow for a few
minutes to flush
through the system.
Remove
cap.
Undo grub
screw and
remove
handle.
56
Replace handle.
Tighten the
grub screw and
replace the cap.
Using a suitable tool,
remove shroud and
retaining nut.
Remove cartridge.
Replace
cartridge.
Screw on retaining
nut and shroud.
Place cartridge in a suitable
solution and soak until fully descaled.
2.5
mm
2.5
mm
IMPORTANT
Isolate the
water supply
before starting!
At Bristan, we want to make things as easy as possible for our customers. That’s why we oer solid guarantees on
all our products, eective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register.
For any other queries, please call our Customer Service on 0330 026 6273 where our expert team of advisors
will be able to oer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
Notes