Brunner banc User manual

banc
Assembly instructions
Design: jehs+laub

Thank you for buying a quality Brunner product from the
banc series.
The modular lounge system is highly versatile and can be
exibly extended and recongured at any time thanks to a
smart principle based on building blocks.
This allows you to completely recongure existing lounge
elements into new landscapes at great speed and with great ease.
After delivery the bases are rst connected to one another and
screwed tight. Several bases can also be combined.
The upholstery elements then simply have to be tted to the
bases with brackets. There is a suitable connector for every
lounge landscape. The assembly instructions below show you all
relevant components and will help you to assemble your banc
lounge system with ease.

BANC ASSEMBLY INSTRUCTIONS
Contents
4
5
6
6
7
8
9
10
11
12
14
15
15
16
17
18
20
21
21
21
21
21
22
22
Elements of the modular lounge system
Conguration examples
Assembly of a lounge element
Fitting the gliders
Fitting the bases
Fitting the seat upholstery
Connecting the seat upholstery
Fitting a supporting plate
Fitting the cabin/Fitting the bases
Fitting the cabin seat upholstery
Connecting the cabin seat upholstery
Connecting several lounge elements
Linear connection of two lounge elements
Connection of two lounge elements back to back
Connection of two lounge elements across a corner
Adding the bar counter
Electrics and cabling
Additional information
General information about assembly
Assembly tool for the modular banc lounge system
Care instructions – powder-coated bases
Care instructions – cover materials and leather
Note
Imprint

ELEMENTS OF THE MODULAR LOUNGE SYSTEM
Table and upholstery elements
BC-H00
BC-T00
BC-H40
BC-H40E
BC-H70
BC-H70E
BC-H100
BC-H100E
Bases
BC-100 BC-200 BC-300

CONFIGURATION EXAMPLES
Congurations of the lounge elements
Elements of the modular lounge system | Conguration examples 4 . 5

ASSEMBLY OF A LOUNGE ELEMENT
FITTING THE GLIDERS
Included in scope of delivery: 2x side section 4x glider

ASSEMBLY OF A LOUNGE ELEMENT
FITTING THE BASES
Included in scope of delivery: 2x cross beam 2x side section 8x M8x16
Frame sizes:
BC-100 BC-200 BC-300
Assembly of a lounge element 6 . 7

4.
1. 2.
3.
95
95
510
95
95
95
510 510190 190
190
95
95
510 510
510190
ASSEMBLY OF A LOUNGE ELEMENT
FITTING THE SEAT UPHOLSTERY
Included in scope of delivery: 4x/8x/12x retaining bracket 1x/2x/3x upholstery 4x/8x/12x M8x25
Position of frame sizes:
BC-100 BC-200 BC-300
Do not fully tighten screw

1.
2.
90°
3.
BC-200 BC-300
2 mm spacing
Middle of
upholstery
10 mm spacing
ASSEMBLY OF A LOUNGE ELEMENT
CONNECTING THE SEAT UPHOLSTERY
Included in scope of delivery: 1x/2x connector tting 8x/16x Spax 4.5x25
Position per frame size:
Screw on connector tting with 10 mm spacing
between the plastic parts
Pull upholstery together
Assembly of a lounge element 8 . 9
Align upholstery to base and screw on

1.
2.
ASSEMBLY OF A LOUNGE ELEMENT
FITTING A SUPPORTING PLATE
Included in scope of delivery: 4x shim/plate 4x M6x16/plate
4x retaining bracket/plate 1x supporting plate
Screw supporting plate on to base
Screw on connector tting

ASSEMBLY OF A LOUNGE ELEMENT
FITTING THE CABIN/FITTING THE BASES
Included in scope of delivery: 4x cross beam 2x side section 700
1x side section 2300 16x M8x16
The gliders and base are assembled in the same way as for the individual lounge element, see page 6-7
BC 3100/3200BC 2100
Assembly of a lounge element 10 . 11

1. 2.
ASSEMBLY OF A LOUNGE ELEMENT
FITTING THE CABIN SEAT UPHOLSTERY
Included in scope of delivery:
16x/24x retaining bracket 16x/24x M8x25 4x M6x25
2x/4x corner upholstery 2x/4x upholstery 1x partition
4x shim 1x strip
Screw on corner upholstery
(do not tighten screws)
Fit base

A
3.
4. 5.
6. 7.
ASSEMBLY OF A LOUNGE ELEMENT
Slide together and screw on second corner upholstery
DETAIL A
Guide pin into hole
Screw on partition (do not tighten screws) Screw on strip
Align upholstery to base
and screw on
Screw on remaining upholstery
(do not tighten screws)
Assembly of a lounge element 12 . 13

ASSEMBLY OF A LOUNGE ELEMENT
CONNECTING THE CABIN SEAT UPHOLSTERY
Included in scope of delivery: 2x/4x connector tting 16x/32x Spax 4.5x25
Align and connect upholstery and tighten screws, see page 8-10

1. 2.
CONNECTING SEVERAL LOUNGE ELEMENTS
LINEAR CONNECTION OF TWO LOUNGE ELEMENTS
Included in scope of delivery: 1x shim 1x M8x25 1x M8 nut
Position lounge elements in linear fashion and screw together
Side sections are supplied pre-drilled and have to be placed on the correct side during assembly
Assembly of a lounge element | Connecting several lounge elements 14 . 15

1. 2.
CONNECTING SEVERAL LOUNGE ELEMENTS
CONNECTION OF TWO LOUNGE ELEMENTS BACK TO BACK
Included in scope of delivery:
2x fastener 4x M8x12 4x M8 sliding block
Position lounge elements back to back and screw
both fasteners on to cross beam near side section
Fit sliding block

3.
1. 2.
4.
CONNECTING SEVERAL LOUNGE ELEMENTS
CONNECTION OF TWO LOUNGE ELEMENTS ACROSS A CORNER
Included in scope of delivery: 1x corner connector 2x M8x25
2x sliding block 2x M8x12
Position lounge elements across corner and
screw corner connector on to side section
Fit sliding block Screw corner connector to cross beam
Side section is supplied pre-drilled and has to
be placed on the correct side during assembly
Connecting several lounge elements 16 . 17

1. 2.
3. 4.
ADDING THE BAR COUNTER
FITTING THE BAR COUNTER
Included in scope of delivery:
1x BC-T02 / BC-T03 4x/5x clothes hook 1x banc with 2 upholstery
sections/3 upholstery
sections
Screw on clothes hook
Screw clothes hook tight
Slide bar element on to threaded pins

1. 2.
ADDING THE BAR COUNTER
FITTING THE BAR COUNTER
Included in scope of delivery: 4x shim 4x M5x10
Screw bar element on to base
Adding the bar counter 18 . 19

4. 5.
1. 2. 3.
ELECTRICS AND CABLING
FITTING THE PROFILE BOX UNDER THE SEAT UPHOLSTERY
Included in scope of delivery: 1x prole box 2x plastic cover 2x M8x12
2x assembly sheet 1x bracket 2x sliding block
2x shim 1x adhesive tape 1x cable duct
Screw the prole box on to the appropriate bracket. Position bracket on cross beam and screw tight.
Stick on cable duct with adhesive tape
Fit plastic cover Slide in assembly sheets at side Screw on bracket and
ground cable
Fit sliding block Fit electrics to cross beam and bring
cable duct into desired position