BT Decor 210 User manual

5
To make a handsfree call
Press the HANDSFREE
button.
The handsfree light will come
on and you will hear the dial
tone. The display will also
show the volume level.
Dial the telephone number.
You can now talk to your caller
through the microphone, or
pick up the handset to speak
to your caller privately.
To receive a call in
handsfree mode
Press the HANDSFREE button
when the phone rings.
To change the volume
on a handsfree call
You can adjust the speaker
volume when you are on a
handsfree call.
Press the VOLUME button.
The volume level will be
shown on the display .
There are 5 levels to choose
from. It is pre-set to the
mid-range level. Press the
VOLUME button to move up
and down each level.
To adjust the
ringer volume
There are 3 ringer volume
settings to choose from:
HIGH, LOW or OFF.
The default setting is HIGH.
Lift the handset and press the
STORE button.
Press the ✱button.
The display will show: BELL
LEVEL HI
Press either, 1for HIGH, 2
for LOW or 3for OFF.
Press the STORE button.
Your selected setting will be
displayed.
You will hear a confirmation
tone and the display will show
SAVEd.
Replace the handset.
(If the ringer is set to OFF,
the call indicator light will still
flash to indicate someone is
calling you. The display will
show RINGER OFF when you
lift the handset or use
handsfree.)
To set the ringer pitch
The ringer pitch can be set to
HIGH or LOW. The default
setting is HIGH.
Lift the handset and press the
STORE button.
Press the
# button.
The display will show BELL
Pitch HI.
Press either, 1for HIGH or 2
for LOW.
Press the STORE button.
You will hear a confirmation
tone and the display will
show SAVEd.
Replace the handset.
Note
You can only change the volume
of a call when using handsfree.
Note
You can swap between using the
handset and handsfree during a
call.
If using the handset, press the
HANDSFREE button and replace
the handset.
If using handsfree, lift the handset
to talk privately.
1 2
At a glance
3
Setting up
Plan the location of
your Decor 210.
Situate your Decor 210 close
enough to a phone socket so
that the line cord will reach.
You can wall-mount your
product, see back page.
Plug your Decor 210
into the telephone
socket.
Your Decor 210 is now ready
for use.
Using the telephone
Safety information
General
Simply clean your Decor 210
with a damp (not wet) cloth, or an
antistatic wipe. Never use household
polish as this may damage the
product. Never use a dry cloth as
this may cause static shock.
Do not open the Decor 210. This
could expose you to high voltages
or other risks.
nvironmental
Do not expose to direct sunlight.
We recommend that you do not
place the product on antique/
veneered wood to avoid damage.
Do not stand your product on
carpets or other surfaces which
generate fibres, or place it in
locations preventing free flow of
air over its surfaces.
Do not submerge any part of
your product in water and do not
use it in damp or humid
conditions, such as in bathrooms.
Do not expose your product to
fire, explosive or other hazardous
conditions.
Making and ending
calls
To make a call
Lift the handset and wait for
the dial tone.
The icon will be shown on
the display to indicate that the
phone is in use.
Dial the telephone number.
Or
Preparatory dialling
Dial the telephone number
without lifting the handset.
It is shown on the display but
will not be dialled. If you have
entered the number incorrectly
press the HANDSFREE button
or lift the handset to clear the
number.
If the number is correct, press
the QUICKDIAL button. Your
Decor 210 will automatically
dial the number using
handsfree. The call can now be
taken using handsfree or you
can use the handset.
To end a call
Replace the handset.
Call timer
Your Decor 210 automatically
times the duration of all
outgoing external calls. The
display will show to
indicate that call timer is on.
The call duration will be
shown both during the call
and for a few seconds after it
is completed.
To receive a call
When the telephone rings the
call indicator light will also
flash to indicate that there is
an incoming call. Simply pick
up the handset.
To redial the last
number called
Lift the handset.
Press the REDIAL button.
The last number called is
displayed and then dialled.
A redial number can be no
longer than 32 digits.
You can also press the REDIAL
button when the handset is
down to check the number first.
If it is correct, press the
QUICKDIAL button. The
number will be dialled
automatically using handsfree.
Secrecy/Music on hold
When on a call you can talk to
someone in the same room,
without your caller hearing.
To switch secrecy
on and off
During a call press and release
the SECRECY button.
Your caller will be put on hold
and both you and the caller
will hear music. You can now
talk to someone in the room
without your caller hearing
you. The display will flash
SECRECY to confirm secrecy
is on.
Press and release the
SECRECY button again to
return to your caller.
Handsfree talking
The handsfree feature allows
you to use the phone without
picking up the handset, giving
you more freedom when you
are speaking on the phone.
You can hear the caller’s voice
through the in-built speaker.
4
Note
If the telephone has been
unplugged the last number dialled
will not be saved.
Note
When secrecy is in use, and
another telephone connected to
the same line is picked up, secrecy
is cancelled and the call will be
transferred to that telephone.
Importa t
Your Decor 210 is specially
designed to operate without the
need of a mains power supply.
It is therefore necessary to make
your first call via the handset.
This call should last at least
1 minute. Subsequent calls can
now be made using the handset
or handsfree feature.
6
Note
Whilst storing a number in
the memory you can cancel
the operation by replacing the
handset on the cradle.
One-Touch memories
You can store your three
most frequently used
telephone numbers in the
One-Touch memories (M1,
M2 or M3). Please note that
the number can be no longer
than 18 digits.
To store a one
touch number
Lift the handset.
Press the STORE button.
The display will show Loc-.
Press the memory location
number, (M1,M2,M3), under
which you want to store the
number. The display will
show, e.g. Loc-dl if you want
to store in M1 location.
Enter the telephone number
you want to store, including
the area code if applicable.
Press the STORE button.
You will hear a confirmation
tone and the display will show
SAVEd. Replace the handset.
To dial a One-Touch
number
Lift the handset and wait for
the dial tone.
Press the memory location
number, (M1,M2,M3), under
which the number is stored.
The number is displayed and
dialled automatically.
You can also dial a One-Touch
number when the handset is
down. Simply press the
memory location number
(M1,M2,M3). Your Decor 210
will automatically dial the
number using handsfree.
To insert a pause in
a memory number
Sometimes you may need to
enter a pause when storing a
number, e.g. with an
overseas number you may
need to enter a pause after
storing the international
code.
Press the REDIAL button in
the place where you want to
enter a pause.
When you dial the number
your Decor 210 will
automatically insert the
pause where you stored it.
Quickdial memories
You can store a further 10
telephone numbers in the
Quickdial memories. Please
note that the numbers can be
no longer than 18 digits long.
To store a number in
the Quickdial memory
Lift the handset.
Press the STORE button.
Enter the memory location
number between 0and 9,
under which you want to
store the number. The display
shows, e.g. Loc-8 if you want
to store in location 8.
Enter the telephone number
you want to store, including
the area code if applicable.
Press the STORE button.
You will hear a confirmation
tone and the display will show
SAVEd. Replace the handset.
Decor 210 ~ Editio 6.1 ~ 30th May ’01 ~ 3527
123
456
789
0
Decor 210
Quickdial
Store
R
Ha dsfree
W
X
Y
Z
M
N
O
D
E
F
T
U
V
J
K
L
A
B
C
P
Q
R
S
G
H
I
Redial
Vol
S
S
e
c
r
e
c
y
Liquid Crystal Display
Displays dialled numbers and
numbers stored in the memory.
Also displays call timer, and other
visible information.
One-Touch memory buttons
(M1,M2,M3)
Allows you to store and dial up to
three numbers at the touch of a
button. If pressed when handset
is down these are dialled
automatically using handsfree.
Secrecy/Music on hold button
Press to talk to someone in the
same room without your caller
hearing you. When pressed music
will be played to both you and
your caller.
Handsfree button
Allows you to hold a conversation
over the loudspeaker without
lifting the handset.
Volume button
Use to adjust the volume during
handsfree operation.
Quickdial button
Allows you to dial the 10 numbers
stored in the Quickdial memory
at the touch of two buttons.
Also used as a dial button when
using preparatory dialling.
Call indicator light
Flashes to indicate an incoming
call. Also flashes when storing
numbers and setting the ringer.
Store button
Use to store numbers in the
memory and to change the ringer
and pitch volume.
Recall button
For use with a switchboard/PBX
and BT Select Services. Please
contact your switchboard supplier
for more information. For more
information on BT’s Select
Services, please call Freefone
0800 800152.
Redial/Pause button
Redials the last number called.
Also, press to enter a pause when
storing a number.
Handset hook
Keeps the handset in place when
the Decor 210 is wall mounted.
See pages 9 & 10 for more
information.
Revolve the handset catch on the
base unit. The handset will now
be able to rest on the hook when
wall-mounted.

This product is intended for connection to analogue public switched
telephone networks and private switchboards in the United Kingdom.
User Guide
Decor 210
To dial a number in
the Quickdial memory
Lift the handset and wait for
the dial tone.
Press the QUICKDIAL button.
Enter the memory location
number between 0and 9,
under which the number is
stored. The number is
displayed and dialled
automatically.
To delete stored
numbers
Lift the handset.
Press the STORE button.
Enter the memory location
number (0-9) or (M1,M2,M3)
under which you have stored
the number you wish to delete.
Press the STORE button. You
will hear a confirmation tone.
Replace the handset.
Alternatively, any existing
number stored in the
One-Touch or Quickdial
memories can be overwritten
by entering a new number
under the same memory
location. Simply follow the
instructions under the storing
numbers sections previously
shown.
7
Note
If any error occurs in the
storing mode you will hear
three short beeps, then the
product will return to talk
mode.
If you unplug your Decor 210
the numbers stored in the
memory will be saved.
However, the last number
redial memory will be lost.
Note
There is a Quickdial memory
label included on the reverse
side of your handset and a
One-Touch memory label on
the base unit. You can use
these labels to keep a record of
which memory location
number you have used for each
telephone number.
Note
You can mix manual and
memory dialling as required,
for example, you can dial the
area code 020 8304 from the
memory and then complete the
number manually.
8
General information
Guarantee
Your Decor 210 is guaranteed
for a period of 12 months from
the date of purchase.
Subject to the terms listed
below the guarantee will
provide for the repair of, or at
BT’s or its agent’s discretion
the option to replace the
Decor 210, or any component
thereof, which is identified as
faulty or below standard, or
fails as a result of inferior
workmanship or materials.
Products over 28 days old from
the date of purchase may be
replaced with a refurbished
product.
The co ditio s of this
guara tee are:
• The guarantee shall only
apply to defects that occur
within the 12 month
guarantee period.
• Proof of purchase is
provided.
• The equipment is returned
to the point of purchase.
• This guarantee does not
cover any faults or defects
caused by accidents, misuse,
fair wear and tear, neglect,
tampering with the
equipment, or any attempt
at adjustment or repair other
than by approved agents.
• This guarantee does not
affect your statutory rights.
Withi the 12 mo th
guara tee period:
In the unlikely event of a
defect occurring, please return
the product, with the receipt,
to the place of purchase.
Outside of the 12 mo th
guara tee period:
If your product needs repair
after the guarantee period has
ended, the repair must meet
the approval requirements for
connection to the telephone
network. We recommend that
you contact BT’s approved
repair agent, TecLogic on
01672 564444 or a local
qualified repairer.
If you have to return
your Decor 210
Pack the unit securely,
preferably in the original
packaging. All parts must be
returned. We cannot take
responsibility for goods
damaged in transit.
Technical information
How ma y telepho es ca
you have?
All items of telephone
equipment have a Ringer
Equivalence Number (REN),
which is used to calculate the
number of items which may
be connected to any one
telephone line. Your Decor
210 has a REN of 1.
A total REN of 4 is allowed, if
the total REN of 4 is
exceeded, the telephones may
not ring. With different
telephone types there is no
guarantee of ringing, even
when the REN is less than 4.
R&TT Directive
Hereby, Suncorp
Technologies Ltd, declares
that this Decor 210 is in
compliance with the essential
requirements and other
relevant provisions of
Directive 1999/5/EC.
The Declaration of
Conformance for the Decor
210 is published on the
website
http://www.suncorptech.com/bt
Switchboard
compatibility
This product is intended for
use within the UK for
connection to the public
telephone network and
compatible switchboards,
which support tone dialling
and time break recall. If in
doubt please consult your
service provider.
Wall
mounting
1. Locate lugs and mount into
holes under base unit as
shown.
2. Swing mount down to clip
into top hole.
3. Drill 2 holes, 25mm deep
using a 3mm drill, for the
screws using the template.
Ensure that you do not drill
into any hidden wiring or
pipes. Insert the wall plugs
provided and then insert a
screw into each hole. Leave
2-3mm between the head of
the screw and the wall.
4. Position the product onto
the screws.
5. Drop down to secure.
4
5
1
2
910
Offices worldwide
The telecommunications services described in
this publication are subject to availability and
may be modified from time to time. Services
and equipment are provided subject to British
Telecommunications plc’s respective standard
conditions of contract. Nothing in this publication
forms any part of any contract.
© British Telecommunications plc 2001.
Registered Office: 81 Newgate Street, London
EC1A 7AJ.
Registered in England No. 1800000.
Decor 210 (5/01) 6.1
Designed by the Art & Design Partnership
Limited.
Printed in China by Suncorp Technologies.
69mm
Decor 210 ~ Editio 6.1 ~ 30th May ’01 ~ 3527
Corded Telephone