1 Plug in
2 Charge
3 Go!
General information
For information on safety instructions,
cleaning, technical information or
connecting to a switchboard, please
refer to the ‘General Information’
section in the full user guide at
www.bt.com/producthelp
Guarantee
Your BT Hudson 1500 is guaranteed for a period of 12
months from the date of purchase.
Subject to the terms listed below, the guarantee
will provide for the repair of, or at BT’s or its agent’s
discretion the option to replace the BT Hudson 1500,
or any component thereof, (other than batteries),
which is identied as faulty or below standard, or as a
result of inferior workmanship or materials. Products
over 28 days old from the date of purchase may be
replaced with a refurbished or repaired product.
The conditions of this guarantee are:
• The guarantee shall only apply to defects that
occur within the 12 month guarantee period.
• Proof of purchase is required.
• The equipment is returned to BT or its agent
as instructed.
This guarantee does not cover any faults or defects
caused by accidents, misuse, fair wear and tear,
neglect, tampering with the equipment, or any
attempt at adjustment or repair other than through
approved agents.
This guarantee does not affect your statutory rights.
For further information within and outside the 12
month guarantee, please refer to the full user guide at
www.bt.com/producthelp
Product disposal instructions
The symbol shown here and on the product
means that the product is classed as Electrical or
Electronic Equipment and should not be disposed with
other household or commercial waste at the end of its
working life.
The Waste of Electrical and Electronic Equipment
(WEEE) Directive (2002/96/EC) has been put in place
to recycle products using best available recovery and
recycling techniques to minimise the impact on the
environment, treat any hazardous substances and
avoid the increasing landll.
Product disposal instructions for residential users
When you have no further use for it, please remove
any batteries and dispose of them and the product as
per your local authority’s recycling processes. For more
information please contact your local authority or the
retailer where the product was purchased.
Product disposal instructions for business users
Business users should contact their suppliers and check
the terms and conditions of the purchase contract
and ensure that this product is not mixed with other
commercial waste for disposal.
Warning
This equipment is not designed for making
emergency telephone calls when the power fails.
Alternative arrangements should be made for
access to emergency services.
R&TTE Directive & Declaration of Conformity
This product is intended for use within the UK for
connection to the public telephone network and
compatible switchboards.
This equipment complies with the essential
requirements for the Radio Equipment and
Telecommunications Terminal Equipment Directive
(1999/5/EC).
If you would like a copy of the Declaration of
Conformance, go to www.bt.com/producthelp
Setting up is easy. Just follow the simple steps in this guide.
If you need further assistance, please visit our website www.bt.com/producthelp
to view our advanced user guide or call our helpdesk on 0808 100 6556*
2 Charge
1 Remove the protective lms from the
handset screen and the base lens and
activate the batteries by pulling the plastic
tab away from the back of the handset.
2 Place the handset on the base to charge.
3 After 24 hours, plug the telephone line
cord into the telephone wall socket.
Important: Charge the handset batteries for 24 hours
or your phone may not work.
Set up your additional handsets (multipacks only)
1 For additional handsets and chargers: plug the mains power adaptor with the red
connector (item code 039955) into the back of the charger and plug the other end
into the mains wall socket and switch the power on.
2. Remove the protective lm from the handset screen and activate the batteries as
explained above.
3. Place the handset on the charger to charge for 24 hours.
If you ever need to remove the batteries, simply slide open the battery
compartment cover and insert your nger nail under the end of the batteries
to pull them out.
Your BT Hudson 1500 is now ready for use.
1 The telephone
line cord is pre-installed
but don’t plug the other
end into the wall socket yet.
2 Plug in mains
power adaptor
(item code 039956).
3 Plug the other end of the
power adaptor into the
wall socket and switch on.
Please
turn
over
Check box contents
The answering machine will switch on and default to ‘Answer and record’ mode.
The base power light will come on.
