Bunker Hill Security 45891 Owner's manual

ELECTRONIC
DIGITAL SAFE
Model 45891
INSTALLATION AND OPERATION INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright©2001 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
REVISED 07b

Page 2SKU 45891 For technical questions, please call 1-800-444-3353.
SPECIFICATIONS
Overall Dimensions 9-7/8” H x 11” D (w/Front Panel),
10-1/2” D (w/o Front Panel) x 13-3/4” W
Internal Dimensions 13-1/2” W x 9-1/2” H x 9-5/8” D
Materials 9 GA. Steel Plate Housing, 4 GA. Steel Door Frame, 5 GA. Steel Door
Door Mounting 3/8” Steel Pins (Welded)
Door Lock Bolt 1” x 5/8” Throw
Panel Features Green LED Code OK/Open
Yellow LED Set/Codes
Red LED Battery Change
Hidden Tumbler with 2 Keys
Key Pad #1 through 0, and A & B Key
Code Set Button (Inside)
Black Knob (Lock/Open)
Eight Digit Code Capacity
Included Items 4 concrete fasteners, Felt pad, Hole Template
Power Required “AA” Batteries x 4
Weight 35.6 lb.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep the invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
WARNING: When using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Read all
instructions before using this product!
Use the right product for the job. There are certain applications for which this product
was designed. Do not modify this product and do not use this product for a purpose for
which it was not intended.
Check for damaged parts. Any part that is damaged should be properly repaired or
replaced by a qualified technician.
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
1.
2.
3.
REV 02d, 04c, 07f

Page 3SKU 45891 For technical questions, please call 1-800-444-3353.
OPERATION
To Open the Safe: Input the numbers “159” on the Electronic Key Pad, then press either
the “A” or “B” Key. Once the Green light is on, turn the Knob and pull the Door open.
Note: The knob must be turned within 5 seconds of the Green light coming on. If the
knob is not turned, the entry code will need to be re-entered.
To Close: Close the Door and turn the Knob in the opposite direction. The Safe is now
locked.
To Change the Code: The Safe comes preset with a default code of “159.”To change the
Code, first follow the instructions for opening the Safe. On the inside of the Door toward
the hinge, you will see a small Red Button. Press this Button until the Yellow Light on the
Front Control Panel lights up. Now you can input the new Code (1 to 8 characters) into
the Front Control Panel, followed by either the “A” or “B” Key. The Safe will beep twice to
confirm that the Code has been changed. Important: If the Safe beeps three times, then
the Code has not been accepted, and you must repeat the steps above.
To Change the Batteries: If the Red Light and the Green Light are both lit at the same
time, it is time to change the Batteries. Follow the instructions for opening the Safe. The
Battery Compartment is located on the inside of the Door. Slide the Battery Cover off of
the Battery Compartment, remove used Batteries, and insert four new “4, AA” Batteries.
Once you have changed the Batteries, be sure to test the Code before you close the
Door again.
Using the Emergency Key:
The Safe comes with two Emergency Keys in case the code is forgotten or the bat-
teries are dead.To override the electronic locking device, detach the Front Panel from
the Safe. There is a sticker to the left of the keypad, with SKU# 45891 printed on it.
Gently peel off that sticker. See Figure 1.
Figure 2Figure 1
Remove the screw under the sticker, as shown in Figure 2.
1.
2.
3.
4.
5.
a.
b.
REV 02d, 04c, 07b

Page 4SKU 45891 For technical questions, please call 1-800-444-3353.
REV 04a, 07b
INSTALLATION
The safe has four concrete fasteners that are inside of the safe when you open it. There
is also a mounting template included with the safe. Place the mounting template against
the area you will be mounting the safe and tape it into place.
WARNING! Before drilling or driving nails, make sure there are no wires, cables or pipes
in the path.
To attach the safe to a wood surface, hammer a nail (not included) to mark the hole
placement. Drill an 1/8” diameter pilot hole into each mounting hole location. Place the
safe over the mounting holes and secure the safe using four 1/4” diameter self-tapping
screws (not included).
To use the concrete fasteners, drill a small pilot hole through the template to mark the
hole placement. Next drill four holes in the correct location, using a concrete drill bit. Drill
the holes the same diameter as the fasteners and 2” deep. Hammer the fastener in the
hole with the flat side going into the hole first. Use a wood block between the bolt and
the hammer to protect the threads.
Place the safe over the bolts (with the nut removed from the bolts) and tighten a nut onto
each bolt. As you tighten the nuts onto the bolts, the fasteners will expand inside the
cement, securing the safe into place.
Note: There are no replacement parts available for this product.
1.
2.
3.
4.
Gently remove the Panel to reveal the Secret Key-Operated Lock. Insert Emergency
Key into the Secret Key-Operated Lock and
turn. Turn Knob and pull Door open. Re-
place the keypad and the sticker when
finished. See Figure 3.
IMPORTANT: NEVER LOCK THE
EMERGENCY KEYS IN THE SAFE!
c.
Figure 3Figure 3