Bunker Hill Security 62368 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2014 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 15f

Page 2 For technical questions, please call 1-888-866-5797. Item 62368
SAFETY OPERATION NETWORKSETTINGS
Table of Contents
Safety......................................................... 2
Specifications ........................................... 5
Set up - Before Use: ................................. 6
Receiver Components and Controls.......... 6
Camera Components and Controls........... 8
Viewing Modes ......................................... 10
Menu > Recording ......... 10
Connecting A/V Output............................. 11
Operating Instructions............................ 12
Receiver Functions................................... 12
Display Functions ..................................... 13
Manual Recording .................................... 14
Video Motion Detection ............................ 14
Using Screen Saver.................................. 14
Using Intercom ......................................... 15
Playback and Delete................................. 16
Remote Viewing through Skype™............ 17
Maintenance Instructions ....................... 18
Troubleshooting ...................................... 18
FCC Notice ............................................... 19
Limited 90 Day Warranty......................... 20
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
VVolts
~Alternating Current
AAmperes
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

Page 3For technical questions, please call 1-888-866-5797.Item 62368
SAFETYOPERATIONNETWORK SETTINGS
Installation Precautions
1. Check federal, state and local
surveillance laws before installing video
and/or audio surveillance equipment.
2. Install only according to these instructions.
Improper installation can create hazards.
3. Do not overreach when installing this product.
Keep proper footing and balance at all times.
This enables better control in unexpected situations.
4. Wear ANSI-approved safety goggles
during installation.
5. Keep installation area clean and well lit.
6. Keep children and bystanders out of
the area during installation.
7. Do not install when tired or when under the
influence of alcohol, drugs or medication.
Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
2. Use as intended only.
3. Do not modify.
4. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Electrical Safety
1. Power Adapter plug must match
the outlet. Never modify the plug in
any way. Unmodified plugs and matching
outlets will reduce risk of electric shock.
2. Do not expose Receiver to rain or wet
conditions. Water entering the Receiver
will increase the risk of electric shock.
3. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the Receiver.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled
cords increase the risk of electric shock.
Service
Have your Surveillance equipment serviced by a qualified repair person
using only identical replacement parts.
This will ensure that the safety of the equipment is maintained.
Camera Safety Warnings
1. To prevent electric shock, do not attempt
to disassemble Cameras. There are
no serviceable parts inside.
2. Use supplied Power Adapters only.
3. Do not expose the Power Adapters to rain
or wet conditions. Water entering the Power
Adapters will increase the risk of electric shock.
4. Do not abuse the Power Adapter cords. Never
use the cords for unplugging the plug from
the outlet. Keep cords away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
5. Handle Cameras with care. Cameras could be
damaged by improper handling or storage.

Page 4 For technical questions, please call 1-888-866-5797. Item 62368
SAFETY OPERATION NETWORKSETTINGS
Receiver Safety Warnings
1. Maintain adequate airflow around Receiver.
2. Use supplied Power Adapter only.
3. Do not expose the Power Adapter or
Receiver to rain or wet conditions. Water
entering the Power Adapter or Receiver
will increase the risk of electric shock.
4. Do not abuse the Power Adapter cord. Never
use the cord for unplugging the plug from the
outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
5. Maintain labels and nameplates on
the unit. These carry important safety
information. If unreadable or missing, contact
Harbor Freight Tools for a replacement.
6. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
7. WARNING: The cord of this product contains
lead and/or di (2-ethylhexyl) phthalate (DEHP),
chemicals known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
8. WARNING: This product contains or, when
used, produces a chemical known to the State
of California to cause cancer and birth defects
or other reproductive harm. (California Health
& Safety Code § 25249.5, et seq.)
9. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the Power Adapter plugs provided. Do not use the equipment if the power cord or plug is
damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have
a proper outlet installed by a qualified electrician.
Figure A
1. The included Power Adapters do
not require grounding.
2. The Power Adapters may be used in
either of the 120 volt outlets shown in the
preceding illustration. (See Figure A.)
Extension Cords
Note: Do not use extension cords with the Power Adapters.

Page 5For technical questions, please call 1-888-866-5797.Item 62368
SAFETYOPERATIONNETWORK SETTINGS
Specifications
Receiver
Screen 7" 4-Channel Color LCD
Video Standard NTSC / PAL
Modulation GFSK
Data Rate 2 Mbps
Resolution 10fps @ 640 x 480
25fps @ 320 x 240
Audio Built-in Microphone
Speaker
Recording
Scheduled
Manual
Motion Detection
Power Rating 5VDC / 2A
Operating Temperature 14° - 104°F
Camera Capacity 4
Memory SD Card (not included)
Cameras
Lens 1/4" VGA CMOS
Effective Pixels 640H x 480V
Night Vision Type Infrared LEDs with Low Light Sensor
Image Type Daylight: Color
Infrared: Black & White
Infrared Wavelength 850nm
Audio Built-in Microphone
Speaker
Wireless Range 180 ft (indoors) 650 ft (outdoors)
Ingress Protection Rating IP54 - Dustproof, Splashproof
Night Vision Range 40 ft
Audio/Video Connector RCA
Power Rating 9VDC / 600 mA
Operating Temperature 14° - 122°F
Transmission Frequency 2.4 GHz

Page 6 For technical questions, please call 1-888-866-5797. Item 62368
SAFETY OPERATION NETWORKSETTINGS
Set up - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Receiver Components and Controls
Back
X
ON
OFF
Antenna
Connector
Power
Switch
Zoom
Speaker
Mounting
Hole
Memory
Card Slot
Mini-B
USB Port
RCA
AV Out
Port
Delete
AV
Output
5VDC
Power Input
Microphone Stand
Figure B
Accessories
USB to
Mini-B Cable
RCA A/V
Cable
5VDC Power
Adapter
Mounting
Hardware Mounting
Bracket
Driver CD
Figure C

Page 7For technical questions, please call 1-888-866-5797.Item 62368
SAFETYOPERATIONNETWORK SETTINGS
Assembly
Thread the Antenna into the Antenna Connector on the back of the Receiver.
Before Mounting
When planning Receiver location:
1. Verify that installation surface has no hidden
utility lines before drilling or driving screws.
2. Select a clean, dry location indoors
with a 120V outlet nearby.
3. Take into consideration the length
of the Power Adapter's cord.
CAUTION! Route the cord so as
to avoid a tripping hazard.
4. Make sure the location will remain within
the Receiver's Operating Temperature.
Tabletop Mounting
Place Receiver on a flat, level surface. Adjust
the Stand until desired position is achieved.
V
V
OK
NEW FULL SCAN
MOTION
Stand
(on back)
Figure D
Wall or Under Cabinet Mounting
Using the Base as a template, mark locations
of mounting holes on mounting surface.
Mounting
Holes
Base
Adjustment
Knob
Adjustment
Knob
Figure E
Solid Surface
1. Using a drill bit slightly smaller than the Screws,
drill pilot holes into the marked locations.
2. Position Mounting Bracket so that
mounting holes align with pilot holes.
3. Drive Screws through mounting holes in Base
and into pilot holes until the Mounting Bracket
is securely attached to the mounting surface.
4. Attach Receiver to Mounting Bracket, then
loosen Adjustment Knobs, adjust Receiver as
needed, then tighten Adjustment Knobs.
Hollow Surface
1. Using a drill bit slightly smaller than the
Anchors, drill holes in the marked locations.
2. Tap Anchors into the holes until they are
almost flush with mounting surface.
3. Position Mounting Bracket so that Mounting
Holes align with anchor holes.
4. Drive Screws through mounting holes in Base
and into anchor holes until the Mounting Bracket
is securely attached to the mounting surface.
5. Attach Receiver to Mounting Bracket, then
loosen Adjustment Knobs, adjust Receiver as
needed, then tighten Adjustment Knobs.
Connect Power
1. Connect the Power Adapter’s cord
to the back of the Receiver.
2. Plug the Power Adapter into a 120VAC outlet.
3. Turn the Power Switch to the ON position.

Page 8 For technical questions, please call 1-888-866-5797. Item 62368
SAFETY OPERATION NETWORKSETTINGS
Camera Components and Controls
Mounting
Bracket
Microphone
(on bottom) Infrared
Sensor
Lens
Speaker
Antenna
Power
Cord
Pair
Button
Antenna
Connector
Power
Cord
Back of Camera
Accessories
Mounting
Hardware
9VDC Power
Adapter
Figure F
Assembly
Thread the Antenna into the Antenna Connector on the back of the Camera.
Before Mounting
Note: The included Cameras are programmed to automatically connect to Channel 1 and Channel 2.
1. When planning mounting location and angle:
a. Verify that installation surface has no hidden
utility lines before drilling or driving screws.
b. Take into consideration the length of the
Camera and Power Adapter’s cords. Route the
cords so as to avoid a tripping hazard.
c. Do not install where there are thick walls or other
obstructions between the Camera and Receiver.
d. Select a location high enough so that
it is out of reach of children, but still
covers the desired viewing area.
e. Do not install the Camera facing out of a window.
f. Make sure no strong light will shine
directly into Camera Lens.
g. Make sure location will remain within the
Camera's Operating Temperature.
2. Test each Camera's function in its
intended location before mounting:
a. Connect the Power Adapter’s cord
to the Camera’s Power cord.
Figure G
b. Plug the Power Adapter into a 120VAC outlet.
c. Verify that there is an image on the Receiver.
Note: If there is no image, pair the Camera to the
Receiver according to Pairing on page 11.

Page 9For technical questions, please call 1-888-866-5797.Item 62368
SAFETYOPERATIONNETWORK SETTINGS
d. Check the Camera's signal strength.
Touch to check Camera 1.
Note: Touch again to check other Camera(s).
Excellent
Optimal
Good
Acceptable
Low
Needs
Adjustment
Figure H
3. Low signal adjustment:
a. Adjust the Camera and or/Receiver antenna(s).
b. Reposition the Camera and/or Receiver.
4. When the mounting location has been chosen:
a. Unplug the Power Adapter's
cord from the Camera.
b. Remove the Camera from the Mounting Bracket.
c. Using the Base as a template, mark
locations of mounting holes on
mounting surface. (See Figure I)
5. Repeat all steps with the other Camera(s).
Mounting to Solid Surface
1. Using a drill bit slightly smaller than the Screws,
drill pilot holes into the marked locations.
2. Position Mounting Bracket so that
mounting holes align with pilot holes.
3. Drive Screws through mounting holes in Base
and into pilot holes until the Mounting Bracket
is securely attached to the mounting surface.
4. Remove protective film from the Lens.
5. Attach Camera to Mounting Bracket, loosen
Adjustment Knob, adjust Camera as needed,
then tighten Adjustment Knob. (See Figure I)
Mounting to Hollow Surface
1. Using a drill bit slightly smaller than the
Anchors, drill holes in the marked locations.
2. Tap Anchors into the holes until they are
almost flush with mounting surface.
3. Position Mounting Bracket so that Mounting
Holes align with anchor holes.
4. Drive Screws through mounting holes in Base
and into anchor holes until the Mounting Bracket
is securely attached to the mounting surface.
5. Remove protective film from the Lens.
6. Attach Camera to Mounting Bracket, loosen
Adjustment Knob, adjust Camera as needed,
then tighten Adjustment Knob. (See Figure I)
Mounting
Holes
Base
Mounting
Bracket
Adjustment
Knob
Figure I
Connect Power
1. Connect the Power Adapter’s cord
to the Camera’s Power cord.
2. Plug the Power Adapter into a 120VAC outlet.

Page 10 For technical questions, please call 1-888-866-5797. Item 62368
SAFETY OPERATION NETWORKSETTINGS
Viewing Modes
• Camera Sequence (Default mode) - Automatic
cycling between Cameras.
Touch to toggle between
Camera Sequence and 4 Camera.
• 4 Camera - View all Cameras at the same time.
Touch to toggle between
4 Camera and Camera Sequence.
• Single Camera - View one Camera at a time.
Touch to switch between Cameras.
• Zoom - Push the
ZOOM
button on the
back of the Receiver to zoom in during
Single Camera Viewing Mode only.
• Screen Saver -Mask Camera view with
a blank screen or image(s).
See Screen Saver on page 11.
Set Up
Menus
• Touch to view Menus.
• Touch VVto navigate through Menus.
• Touch OK to access highlighted Menu.
• Touch VVto navigate within Menus.
• Touch at any time to cancel an action
and/or go to the previous screen.
Menu > Recording
1. Insert an SD card to enable recording.
SD
will
display to indicate the card is functioning properly.
2. Touch then select Recording.
3. Quality: Select HIGH (640 x 480) or
LOW (320 x 240), then touch OK.
4. Motion Record:
a. Duration: Select the amount of time to record
after motion has been detected, then touch OK.
b. Recording Mode: Select from
below, then touch OK:
• 4 Channel: Record all channels when
a single camera detects motion.
• Single Channel. Record the channel
for the Camera that detects motion.
5. Schedule Record:
Note: Date and time must be set before setting up
Scheduled Recording. See Date & Time on page 11.
a. Select a day to schedule, then touch OK.
b. Enter Start Time and End Time, then select ON.
Note: Time is in 24 hour format.
c. Repeat steps for other days.
Note: For manual recording, see
Manual Recording on page 14.
6. Overwrite:
a. Select Yes to overwrite previously
recorded files when the SD card is full.
Note: After selecting Yes, will display
while in Auto Sequence mode.
b. Select No to keep all files.
Note: After selecting No, when the SD
card is full, the Receiver will stop recording
and the FULL indicator will display.
Menu > Camera On/Off
1. Touch then select Camera On/Off.
2. Touch to select a Camera.
3. To turn the Camera off, touch Vto select OFF.
4. To turn the Camera on, touch Vto select On.
5. Repeat steps for other Cameras.
6. Touch OK to save changes.