Bunker Hill Security 94799 User manual

WIRELESS HOME ALARM
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
94799
Due to continuing improvements, actual product may
differ slightly from the product described herein.

SKU 94799 For technical questions, please call 1-800-444-3353 Page2
Specifications
Item Description
Function 6-station, wireless sensors detect and sound when
door or window is opened.
Alarm Delay Time 5 seconds after sensor tripped
System Range From Sensors to Main Unit: 328 to 500 feet
Batteries Main Unit: 3-AA; Sensors: 3-SR54 (each); Remote
control: 1-23A (12VDC)
Main Unit LED lights and high pitch sound heard when
numbered sensor is tripped; Modes: Alarm/Off/Chime
Key Chain
Remote Controls System modes: On and Off; LED indicator.
Mounting Double-sided adhesive foam pads (supplied)
Dimensions Sensors: 1-7/8 (W) x 3-7/8 (L) x 1/2 (T) inches
Main Unit: 2-1/4 (L) x 4-1/4 (L) x 1-3/8 (D) inches
Magnetic Strip: 1/2 (W) x 3-1/4 (L) x 3/8 (T) inches
System Weight 1.45 lbs. (all components together)
SaveThis Manual
Youwillneedthemanualforthesafetywarningsandprecautions,assemblyinstructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice
with this manual. Write the invoice number on the inside of the front cover. Keep the
manual and invoice in a safe and dry place for future reference.
SafetyWarnings and Precautions
WARNING:Whenusingtool,basicsafety precautions shouldalwaysbe followed
to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Don’t expose components to rain. Keep
work area well lighted.
3. Keep children away. Children must never be allowed in the work area or on
ladders.
4. Storing this product. When not in use, this product must be stored in a dry
location to protect system components.
5. Use the right product for the job. Do not use this alarm system to take the
place of a high-end alarm system where the protection of entry is of great
importance.There are certain applications for which this product was
designed.Do not modify this product, and do not use this tool for a purpose
for which it was not intended.

SKU 94799 For technical questions, please call 1-800-444-3353 Page3
6. Do not overreach. Whenusing aladder, keepproper footingand balanceat
alltimes.
7. Stay alert. Watch what you are doing, use common sense.
8. Replacement parts and accessories. When servicing, use only identical
replacement parts.Use of any other parts will void the warranty. Only use
accessories intended for use with this tool.Approved accessories are
available from Harbor FreightTools.
Note:Performance of this product may vary depending on variations in Sensor and
Main Unit battery power.
Warning:The warnings,cautions,and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur.It
mustbeunderstoodby the operator that common sense andcautionarefactors
which cannot be built into this product,but must be supplied by the operator.
Unpacking
Whenunpacking,checktomakethatalltheWirelessHomeAlarmSystemcomponents
areincluded.See photobelow.Ifanyparts aremissing orbroken,pleasecall Harbor
FreightTools at the number on the cover of this manual.
Installation
1. Snap off the back cover of the Main Unit and install three, quality AA batteries
(not supplied) into the Main Unit.Pay attention to the battery polarity
(+and -).See photo below-left.
Remote Controls
and Batteries
(above)
Main Unit
Sensors 1 to 6
Magnetic Strip
Adhesive Strips
for Sensors and
Main Unit

SKU 94799 For technical questions, please call 1-800-444-3353 Page4
2. Unscrew the back cover of each Remote Control and insert the battery
(supplied) into the back of the Remote.Pay attention to the battery polarity
(+and-). Seephotobelow-right.
Note: Each Sensor comes with a battery installed.Since the internal battery is only
used when the Magnetic Strip is moved away (sensor tripped), it should last two
years.The batteries of the Remote Controls should also last two years.
3. Select the six Sensor locations.They should be placed in the most likely point
of entry, (i.e., doors or windows), or exit points, if used to protect entry to
areas such as to swimming pools.
4. Select an area on the movable part of the door or window where the Sensor
can be mounted flat.The Magnetic Strip must be mounted parallel to, and no
more than 1/4 inch from, the Sensor.The Sensor and Magnetic Strip may be
mounted upside down to accommodate door or window configuration.
Note: Itisrecommendedto test eachSensorwithitsMagnetic Stripbeforemounting.
Refer to the Operation section on page 5.
5. Peel off the backing to one of the Adhesive Pads and squarely stick it to the
back of one of the Sensors.
6. Peel off the remaining Adhesive Pad backing and secure the Sensor to its
mountinglocation.
Main Unit
Remote Control
Window Frame
Window
Door Frame
Door

SKU 94799 For technical questions, please call 1-800-444-3353 Page5
7. Peel the Adhesive Pad backing from one of the Magnetic Strips and mount it
parallel to, and no more than 1/4 inch from, the Sensor.See photos at the
bottom of page 4.
8. Repeat steps 5 to 7 for each Sensor and Magnetic Strip.
9. Usingasmall round-headscrew (notsupplied), screwinto the desired
mounting location.Place the hole in the back of the Main Unit over the screw,
and slide the unit down to lock in place.
Note: Not all the Sensors need to be used for the Wireless Home Alarm to work.
Operation
Controls and Indicators
Setup for Operation
1. On each Sensor, push the slide switch to the desired operating position:
RF+Alarm (signal and sound) or RF (signal, no sound).
2. On the Main Unit, push the slide switch to the desired operating position:
Alarm (loud noise) or Chime (Ding-dong sound).
Main Unit
Sensor
Sensor LED lights
when Sensor tripped.
Alarm - Loud noise
when Sensor tripped.
Chime - Ding-dong
sound when Sensor
tripped.
Off - Unit turned off.
Off - Sensor turned off.
RF - Sensor On; No
sound when tripped.
Sensor # lights on
Main Unit.
RF+Alarm - Sensor On;
Sensor Sounds when
tripped. Sensor # lights on
Main Unit.

SKU 94799 For technical questions, please call 1-800-444-3353 Page6
Arm Alarm System
On the Remote Control, press the ON button.The LED on the Remote Control will
temporarily turn on.This can be done from outside the house or other protected
structure.
Disarm Alarm System
On the Remote Control, press the OFF button.The LED on
the Remote Control will temporarily turn on.This can be
donefrom outsidethe houseor otherprotected structure.
Troubleshooting
Problem Possible Cause Probable Solution
When system is armed,
one sensor does not sound
or signal Main Unit when
Magnet Strip is moved.
1. Sensor is turned Off.
2. Battery is dead.
3. Main Unit is turned Off.
1. Turn Sensor On.
2. Replace battery.
3. Turn Main Unit On.
One Sensor continues to
sound alarm even through
the door is closed.
Magnetic Strip is placed too
far from Sensor. Move Magnetic Strip to within ¼” of the Sensor.
Main Unit does not detect
any intrusions from any
Sensors.
1. Main Unit batteries are
dead.
2. Main Unit is placed too
far from the Sensors.
1. Replace batteries.
2. Move Main Unit closer to
the Sensors.
Maintenance
1. Periodically test each Sensor and Main Unit for alarm indication and sound.
2. Periodically test each Remote Control for Main Unit activation and
deactivation.
3. Replace Main Unit batteries at least once a year.Replace other batteries as
required.
Remote Control

SKU 94799 For technical questions, please call 1-800-444-3353 Page7
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TOTHE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS AND NOT BY THE BUYER.THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Parts List
Item Description Qty
1. Main Unit 1
2. Sensor 6
3. Magnetic Strip 6
4. Battery, Remote Control 2
5. Remote Control 2
6. Battery, Sensor 6
7. Pads, Adhesive 6
Parts Photo
(1)
(2)
(2)
(2)
(2)
(2)
(2)
(3) (3) (3)
(3) (3) (3)
(5)(5)
(4) (4)
(7)
(6) Sensor Battery not shown.
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.