Burkert FLOWave L 8098 User manual

QUICKSTART - English
Software version A.04.00.00 and higher
Type 8098
FLOWave L
SAW Flowmeter

We reserve the right to make technical changes without notice.
© Bürkert SAS, 2015 – 2022
QUICKSTART 2203/09_EU-EN 00567159 / Original EN

3
Table of Contents
Type 8098FLOWaveL
1THE QUICKSTART..................................................................................................................................7
1.1 Symbols used............................................................................................................................... 7
1.2 Denitionofthetermdevice .......................................................................................................8
1.3 DenitionofthetermbüS............................................................................................................8
1.4 ValidityoftheQuickstart..............................................................................................................8
2INTENDED USE ......................................................................................................................................9
2.1 DevicewithATEX/IECExcertication ......................................................................................9
3BASIC SAFETY INFORMATION ...........................................................................................................10
4GENERAL INFORMATION....................................................................................................................12
4.1 Manufacturer'saddressandinternationalcontacts ................................................................12
4.2 Warrantyconditions...................................................................................................................12
4.3 InformationontheInternet........................................................................................................12
5DESCRIPTION ......................................................................................................................................13
5.1 Devicevariants...........................................................................................................................13
5.2 Wi-Fimodule ..............................................................................................................................15
5.3 Unlockingmagnetickey ............................................................................................................15
5.4 Type labels ................................................................................................................................16
5.4.1 Adhesive labels ..........................................................................................................16
5.4.2 Laser marking .............................................................................................................18
5.5 MarkingwiththeMACaddress .................................................................................................18
5.6 Certicationmarkings................................................................................................................18
5.7 MarkingoftheUniqueSerialNumber(USN) ............................................................................19
5.8 Devicestatusindicator .............................................................................................................19
6TECHNICAL DATA ................................................................................................................................ 20
6.1 Operatingconditions .................................................................................................................20
6.2 Conformitytostandardsanddirectives ...................................................................................21
6.2.1 Conformity to the Pressure Equipment Directive .......................................................21
6.2.2 ULcertication ...........................................................................................................21
6.2.3 EHEDGcertication....................................................................................................22
6.2.4 ATEX/IECExcertication..........................................................................................22
English

4
Type 8098FLOWaveL
6.3 Liquiddata .................................................................................................................................23
6.4 Measurementdata .....................................................................................................................25
6.4.1 Volumeowrate .........................................................................................................25
6.4.2 Temperature................................................................................................................25
6.4.3 Dierentiationfactor ...................................................................................................25
6.4.4 Acoustic transmission factor ......................................................................................26
6.4.5 Density........................................................................................................................26
6.4.6 Massowrate ............................................................................................................26
6.5 Electricaldata ............................................................................................................................27
6.6 Mechanicaldata........................................................................................................................29
6.7 SpecicationsoftheEthernetIndustrialcommunication .......................................................29
7INSTALLATION IN A PIPE.....................................................................................................................30
7.1 Safetyinstructions .....................................................................................................................30
7.2 Additionaldocumentation ........................................................................................................31
7.3 Preparingthedevicebeforeinstallationintothepipe .............................................................31
7.3.1 Changing the position of the transmitter on the sensor ............................................31
7.3.2 Switching positions of the blind cover and the display module or the Wi-Fi module 35
7.4 Recommendationsfortheinstallationintothepipe ................................................................38
7.5 Installingthedeviceintothepipe .............................................................................................41
7.5.1 Before installing the device into the pipe....................................................................41
7.5.2 Installingadevicewithclampconnections................................................................41
7.5.3 Installingadevicewithangeconnections ................................................................41
7.5.4 Installingadevicewithexternal-threadedconnectionsaccordingto
DIN11851seriesAforpipesaccordingtoDIN11850..............................................42
8ELECTRICAL INSTALLATION ..............................................................................................................43
8.1 Safetyinstructions ....................................................................................................................43
8.2 Additionaldocumentation .........................................................................................................45
8.3 Connectingthedevicetoapowersupply ................................................................................45
8.4 ConnectingthedevicetoabüS/CANopennetwork .............................................................. 46
8.5 Activatingthedeviceinternalterminationresistor ...................................................................48
8.6 SpecicationsofthecablesfortheM20x1.5cableglands(devicevariantwith
cableglands)..............................................................................................................................48
English

5
Type 8098FLOWaveL
8.7 Specicationsoftheconductorsforthe12push-interminalstrip .........................................48
8.8 Terminalassignmentofthe12push-interminalstrip ..............................................................49
8.9 Openingthefrontofthetransmitter.......................................................................................... 50
8.10 WiringthedevicethroughtheM20x1.5cableglandsinstainlesssteel(device
variantwithcableglands)..........................................................................................................51
8.11 WiringthedevicethroughtheM20x1.5cableglandsinnickelplatedbrass(device
variantwithcableglands)..........................................................................................................53
8.12 Connectingthefunctionalearth(devicevariantwithtwoM20x1.5cableglands) .................56
8.13 Connectingthedevicetoa12...35VDCpowersupplythroughtheM20x1.5cable
glands(devicevariantwithcableglands).................................................................................57
8.14 Wiringoutput1(analogue)andoutput3conguredasananalogueoutput(device
variantwithcableglands)..........................................................................................................58
8.15 Wiringoutput2(digital)andoutput3conguredasadigitaloutput(devicevariant
withcableglands) ......................................................................................................................59
8.16 KnowingthestatusoftheEthernetnetwork(devicevariantwithtwo4-pinM12
femaleconnectors-Ethernetdevicevariant)...........................................................................60
8.17 Specicationsofthecablesandconductorsforthe4-pinM12femaleconnectors..............61
8.18 ConnectingthedevicetoanEthernetnetwork(devicevariantwithtwo4-pinM12
femaleconnectors-Ethernetdevicevariant)...........................................................................61
8.19 Connectingthefunctionalearth(devicevariantwithtwo4-pinM12femalecon-
nectors-Ethernetdevicevariant) ............................................................................................. 62
9HOW TO DO THE SETTINGS ...............................................................................................................63
9.1 Safetyinstructions .....................................................................................................................63
9.2 Availablesoftwaretodothesettings........................................................................................63
9.3 ConnectthedevicetotheBürkertCommunicatorsoftware ..................................................63
9.4 Displaymodule:descriptionoftheuserinterface...................................................................65
9.5 Availableloginuserlevels .........................................................................................................65
9.5.1 Changing the login user level if the adjustment is not protected through passwords66
9.5.2 Changing the login user level if the adjustment is protected through passwords......67
9.5.3 Logging out from the Advanceduser, Installer or Bürkert user level .....................67
9.6 Readingouttheaccesspathtoamenuitem(displaymoduleonly)......................................68
9.7 DoingtheQuickstartadjustmentswhenenergizingthedeviceforthersttime
(displaymoduleonly) .................................................................................................................68
9.8 Changingthetypeofoutput3..................................................................................................69
English

6
Type 8098FLOWaveL
10 COMMISSIONING ...............................................................................................................................70
10.1 Safetyinstructions ....................................................................................................................70
10.2 Prerequisites .............................................................................................................................70
10.3 Firstcommissioningformeasuringtheowrateorforllingcontainers ..............................70
10.4 Firstcommissioningfordetectingachangeofliquidinthepipe ..........................................71
10.5 Firstcommissioningfordetectingbubblesinthepipe...........................................................73
11 MAINTENANCE AND TROUBLESHOOTING ......................................................................................74
11.1 Safetyinstructions .....................................................................................................................74
11.2 Informationonreturningthedevicetothemanufacturerortothereseller ............................75
11.3 Cleaningtheoutersurfaceofthedevice..................................................................................75
11.4 Troubleshootingwhennomessageisdisplayed .....................................................................75
11.5 Troubleshootingwhenamessageisdisplayed........................................................................76
12 SPARE PARTS AND ACCESSORIES ...................................................................................................77
13 PACKAGING, TRANSPORT..................................................................................................................78
14 STORAGE .............................................................................................................................................78
15 DISPOSAL OF THE DEVICE.................................................................................................................78
English

7
The Quickstart
Type 8098FLOWaveL
1 THE QUICKSTART
The Quickstart includes main information and instructions for using the device.
ThecompletedescriptionofthedeviceisintheOperatingInstructionsofthedevice.
Please keep this Quickstart in a safe place, accessible to all users and any new owners.
Importantsafetyinformation.
Fully read the Quickstart. Inparticular,observethesafetyrecommendationsandintendeduse.
▶The Quickstart must be read and understood.
ThefullOperatingInstructionsareavailableontheinternetatcountry.burkert.com
1.1 Symbols used
DANGER
Warnsagainstanimminentdanger.
▶Failure to observe this warning results in death or in serious injury.
WARNING
Warnsagainstapotentiallydangeroussituation.
▶Failure to observe this warning can result in serious injury or even death.
CAUTION
Warnsagainstapossiblerisk.
▶Failure to observe this warning can result in substantial or minor injuries.
NOTICE
Warnsagainstmaterialdamage.
Indicatesadditionalinformation,adviceorimportantrecommendations.
Refers to information contained in the Quickstart or in other documents.
▶Indicatesaninstructiontobecarriedouttoavoidadanger,awarningorapossiblerisk.
→Indicatesaworkstepwhichyoumustcarryout.
A highlightedterm is related to a menu or a menu item.
Indicatestheresultofaspecicinstruction.
English

8
The Quickstart
Type 8098FLOWaveL
1.2 Denition of the term device
Theterm"device"usedintheQuickstartalwaysreferstotheType8098FLOWaveLowmeter.
1.3 Denition of the term büS
The term "büS" used in the Quickstart refers to the industrial communication, developed by Bürkert, based
ontheCANopenprotocol.Theterm"büS"referstotheBürkertsystembus.
→For more information on büS, read the cabling guide available in English and in Japanese (Cabling_
guide_for_büS/EDIP.pdf)atcountry.burkert.com.
→FormoreinformationonCANopenwhichisrelatedtothedevice,refertotheOperatingInstructions
"CANopenNetworkconguration"atcountry.burkert.com.
1.4 Validity of the Quickstart
TheQuickstartisvalidforthedevicesfromsoftwareversionA.04.00.00.
To read out the version number of the device software, do the following:
→Go to the CONFIGURATION view.
→Generalsettings
→ConrmtoaccesstheParameter view.
→GototheMAINTENANCE view.
→Deviceinformation
→Softwareversion
→Gobacktotheparentmenu.
English

9
Intended use
Type 8098FLOWaveL
2 INTENDED USE
Useofthedevicethatdoesnotcomplywiththeinstructionscouldpresentriskstopeople,nearby
installationsandtheenvironment.
TheType8098FLOWaveLowmeterusestheSurfaceAcousticWave(SAW)measurementprinciple
andisintendedtomeasuretheowrateofliquidsthathaveallofthefollowingcharacteristics:
- clean liquids
- nonemulsiedliquids(homogeneousliquids)
- liquids that are free of air bubbles
- liquids that are free of gas bubbles
- liquids that are free of solids.
▶Thedeviceisnotintendedtomeasuretheowrateofliquidsifgasbubblesarepresent,whateverthe
originofthebubbles(airintake,cavitation,degassing…).
▶Use the device in compliance with the characteristics and the conditions of commissioning and use
speciedinthecontractualdocumentsandintheOperatingInstructions.
▶Protect the device against electromagnetic interference, ultraviolet rays and, when installed outdoors,
againsttheeectsofclimaticconditions.
▶Only operate a device in perfect working order.
▶Properly transport, store, install and operate the device.
▶Only use the device as intended.
2.1 Device with ATEX/IECEx certication
DANGER
Riskofexplosionintheeventofimproperuseofthedeviceinpotentiallyexplosiveareas.
▶ObservethespecicationsoftheATEX/IECEx-conformitycerticate.
▶ObservethespecicationsintheATEX/IECExsupplementforType8098FLOWaveL.Thesupplement
is available at country.burkert.com.
TheATEX/IECExcerticationisonlyvalidifthedeviceisusedasdescribedinthe
ATEX/IECExsupplement.
Ifunauthorizedchangesaremadetothedevice,then theATEX/IECExcerticationbecomesinvalid.
English

10
Basic safety information
Type 8098FLOWaveL
3 BASIC SAFETY INFORMATION
This safety information does not take into account any contingencies or occurrences that may arise during
installation, use and maintenance of the device. The operating company is responsible for the respect of the
localsafetyregulations,includingstasafety.
Riskofinjuryduetoelectricalvoltage.
▶Before carrying out work on the system, disconnect the electrical power for all the conductors and isolate it.
▶InaccordancewithstandardUL/EN61010-1,allequipmentconnectedtotheType8098FLOWaveL
owmetershallbedoubleinsulatedwithrespecttothemainsandallcircuitsconnectedtotheType
8098FLOWaveLowmetermustbelimitedenergycircuits.
▶Observe all applicable accident protection and safety regulations for electrical equipment.
Riskofinjuryduetopressureintheinstallation.
▶Beforeanyinterventionintheinstallation,stopthecirculationofliquid,cutothepressureanddrainthe
pipe.
▶Before any intervention in the installation, make sure there is no pressure in the pipe.
▶Observethedependencybetweentheliquidtemperatureandtheliquidpressureforthettingused.
Ifswitchedonforaprolongedtime,riskofburnsorreduetohotdevicesurfaces
▶Do not touch with bare hands.
▶Keepthedeviceawayfromhighlyammablesubstancesandliquids.
Riskofburnsduetohighliquidtemperatures.
▶Do not touch with bare hands the parts of the device that are in contact with the liquid.
▶Use safety gloves to handle the device.
▶Before opening the pipe, stop the circulation of liquid and drain the pipe.
▶Before opening the pipe, make sure the pipe is completely empty.
Riskofinjuryduetothenatureoftheliquid.
▶Respect the prevailing regulations on accident prevention and safety relating to the use of dangerous
liquids.
English

11
Basic safety information
Type 8098FLOWaveL
Generaldangeroussituations
To avoid injury, obey the following instructions:
▶Donotusethedeviceinexplosiveatmospheres1).
▶Do not use the device in an environment incompatible with the device materials.
▶Do not use liquid that is incompatible with the device materials. Find the compatibility chart on our
homepage: country.burkert.com
▶Do not subject the device to mechanical loads.
▶Donotmakeanymodicationstothedevice.
▶Prevent any unintentional power supply switch-on.
▶Onlyqualiedandskilledstamaycarryoutinstallationandmaintenancework.
▶Ensureadenedorcontrolledrestartingoftheprocessafterapowersupplyinterruption.
▶Observe the general technical rules.
1) only applicable for devices without ATEX/IECEx certication
CAUTION
Riskofinjuryduetoaheavydevice.
A heavy device can fall down during transport or during installation and cause injuries.
▶Transport, install and dismantle a heavy device with the help of another person.
▶Use appropriate tools.
NOTICE
Elementsandcomponentssensitivetoelectrostaticdischarges
▶This device contains electronic components that are sensitive to electrostatic discharges. They may be
damagediftheyaretouchedbyanelectrostaticallychargedpersonorobject.Intheworstcasesce-
nario, these components are instantly destroyed or disabled as soon as they are activated.
▶To minimise or even avoid any damage caused by an electrostatic discharge, take all the precautions
describedinstandardEN61340-5-1.
▶Also make sure that you do not touch any of the live electrical components.
English

12
General information
Type 8098FLOWaveL
4 GENERAL INFORMATION
4.1 Manufacturer's address and international contacts
To contact the manufacturer of the device, use the following address:
Bürkert SAS
Rue du Giessen
BP 21
F-67220TRIEMBACH-AU-VAL
YoumayalsocontactyourlocalBürkertsalesoce.
Theaddressesofourinternationalsalesocesareavailableontheinternetat:country.burkert.com
4.2 Warranty conditions
The condition governing the legal warranty is the conforming use of the device in observance of the oper-
atingconditionsspeciedintheOperatingInstructions.
4.3 Information on the Internet
YoucanndtheoperatinginstructionsandthetechnicaldatasheetsforType8098FLOWaveLat:
country.burkert.com
English

13
Description
Type 8098FLOWaveL
5 DESCRIPTION
5.1 Device variants
TheType8098FLOWaveLowmeterismadeupofaTypeSE98transmitterandaTypeS097owsensor.
ThefollowingpicturesdescribethemaindevicevariantsoftheType8098FLOWaveLowmeter:
• Fig.1describesadevicewithtwoM20x1.5cableglandsinstainlesssteel(orinnickelplatedbrass)and
one5-pinM12maleconnector.
• Fig.2 describes the Ethernet device variant, i.e. a device with two 4-pin M12 female connectors and
one5-pinM12maleconnector.
ordisplaymodule(TypeME31)
Device status indicator, seal
Transmitter housing, including
the electronic modules
Type SE98
transmitter
TypeS097ow
sensor
M20x1,5cableglandsinnickel
plated brass, with blind plugs
5-pin M12 male connector, with
screwed plug
Sensor measurement tube
Seal
Type8098FLOWaveLowmeter
Sensor housing
Seal
Blind cover
Pressure compensating
element
Blind cover
Processconnection1)
Functional earth
orM20x1,5cableglandsin
stainless steel, with blind plugs
1) The process connections can be either clamp connections, ange connections or external-threaded connections.
Fig.1: Description of the device variants with twoM20x1.5 cable glands and one5-pin M12 male connector
English

14
Description
Type 8098FLOWaveL
ordisplaymodule(TypeME31)
Device status indicator, seal
Transmitter housing, including
the electronic modules
Type SE98
transmitter
TypeS097ow
sensor
Seal
5-pin M12 male connector, with
screwed plug
Blind cover
Sensor housing
Processconnection1)
Type8098FLOWaveLowmeter
Sensor measurement tube
4-pin M12 female connectors
with screwed plugs
Blind cover
Pressure compensating
element
Seal
Functional earth
1) The process connections can be either clamp connections, ange connections or external-threaded connections.
Fig.2: Description of an Ethernet device variant, with two4-pin M12 female connectors and one5-pin M12 male
connector
English

15
Description
Type 8098FLOWaveL
5.2 Wi-Fi module
The device can be equipped with a Wi-Fi module in place of or in addition to the display module. The Wi-Fi
module has the Type number ME31, too. The Wi-Fi module has the same functional scope as the display
module.
The Wi-Fi module is intended for use in Europe, the USA, and Canada.
ThemodulecanbeintegratedintoanexistingWLANinfrastructure.Thewirelessrangeisapproximately
10m.
The module provides a web server which can be accessed if the following requirements are met:
• Windows7/8.1/10:IE11,Edge,GoogleChrome,fromversion53.
• Android with Google: Chrome, from version 53.
• Apple: Safari, from iOS 9.3.5.
→FormoreinformationsabouttheWi-Fimodule,refertotheSoftwaremanualME31|WLANmodule,
available at country.burkert.com.
5.3 Unlocking magnetic key
The device is delivered with a magnetic key to unlock the display module, the Wi-Fi module or the blind
cover. See Fig.3.
Fig.3: Unlocking magnetic key
Thedeviceoperatesona4-wiresystemandneedsa12...35VDCpowersupply.
The device has three outputs:
• 1 analogue output,
• 1 digital output,
• 1output,whichcanbeconguredasananalogueoutputorasadigitaloutput.
English

16
Description
Type 8098FLOWaveL
5.4 Type labels
5.4.1 Adhesive labels
8098 FLOWave L
Supply: 12-35 5W Max.
IP65 / IP67 / NEMA4X
Ambient Temp : -10 to 70°C
88888888 SN 9999
W49MN
Made in France
21
5
810
4
6
F-67220 Triembach
28-06
12 9
CAN shield
CAN_H GND
V+
21
34 5 CAN_L
3
11
7
1. Supply voltage
2. Type of the device
3. Power consumption
4. IP-Code,NEMAprotectiontype
5. Ambient temperature range
6. Pin assignment of the 5-pin M12 male connector
7. Manufacturing code
8. Serial number
9. Conformity marking
10.Article number
11.Warning: Before using the device, take into
accountthetechnicalspecicationsgiveninthe
OperatingInstructions.
12.Certication
Fig.4: Type label of the Type 8098FLOWaveL owmeter (example of a UL device)
English

17
Description
Type 8098FLOWaveL
8098 FLOWave L
IP65 / IP67 / NEMA 4X
Ambient temp.: -10 to 55°C
88888888 SN 9999
W49MN
Made in France
21
68
3
4
F-67220 Triembach
28-06
10 7
CAN shield
CAN_H GND
V+
21
34 5 CAN_L
9
5
1. IP-Code,NEMAprotectiontype
2. Type of the device
3. Ambient temperature range
4. Pin assignment of the 5-pin M12 male connector
5. Manufacturing code
6. Serial number
7. Conformity marking
8. Article number
9. Warning: Before using the device, take into
accountthetechnicalspecicationsgiveninthe
OperatingInstructions.
10.Certication
Fig.5: Type label of the Type 8098FLOWaveL owmeter (example of a non-UL Ethernet device)
S097 FLOWave Flow sensor
Pipe: 316L/1.4435 Housing: 304/1.4301
DIN 11866 C / Clamp D50.5 DIN 32676 B DN15
PN25bar Max. flow:10 m3/h
Temp. medium : -20 to 110°C
W4ZMN
Made in France
1
2
4
6
7
3
5
F-67220 Triembach
1. Typeoftheowsensor
2. Material of the pipe, material of the housing
3. Standardthepipeconformsto;typeofprocessconnection,externaldiameteroftheclampandstandard
theprocessconnectionconformsto;DNofthemeasurementtube
4. Pressureclassofthedeviceandmaximumowrate
5. Liquid temperature range
6. Manufacturing code
7. Conformity marking
Fig.6: Type label of the Type S097 ow sensor (example)
English

18
Description
Type 8098FLOWaveL
5.4.2 Laser marking
Measuring
Equipment
N°E237737
28-06
Type: 8098 FLOWave L
ID:00xxxxxx | S/N:001234
W49MN
CRN 0C21751.5
Supply: 12...35V 5W Max.
IP65 | IP67 | NEMA4X
Ambient Temp: -10°...+70°C
Slot5:
Slot4:
Slot3:
Slot2:
Slot1:
1
2
3
4
5 6 78
9
1011
12
13
1. Type of the device
2. Article number | Serial number
3. Manufacturing code
4. CanadianRegistrationNumber(CRN)
5. Conformity marking
6. Electronic modules
7. Supported protocols, Ethernet device variant
8. Warning: Before using the device, take into
accountthetechnicalspecicationsgiveninthe
OperatingInstructions.
9. Certications
10.Power consumption
11. Operating voltage
12.IP-Codes,NEMAprotectiontype
13. Ambient temperature range
Fig.7: Laser marking, Type 8098FLOWaveL owmeter (example of a UL Ethernet device)
5.5 Marking with the MAC address
The marking with the MAC address can be seen by opening the front of the transmitter.
→Toopenthefrontofthetransmitter,seechapter8.9.
DC-B0-58-FF-FF-FF
Fig.8: Marking with the MAC address of the device (example)
5.6 Certication markings
CerticationmarkingsareeitherlocatedontheTypelabelofthemeasuringdeviceoronseparatelabels.
English

19
Description
Type 8098FLOWaveL
5.7 Marking of the Unique Serial Number (USN)
TheUSNismarkedonthesideofthesensor.TheUSNisbuiltwiththedevicearticlenumberandthe
device serial number.
5.8 Device status indicator
ThedevicestatusindicatorchangesitscolourbasedontheNAMURNE107recommendation.
The color of the device status indicator gives the following pieces of information:
• Whether device diagnostics are active on not.
• Ifdevicediagnosticsareactive,thenthedevicestatusindicatorshowswhetherdiagnosticseventshave
beengeneratedornot.Ifseveraldiagnosticseventshavebeengenerated,thenthedevicestatusindicator
shows the diagnostics event with the highest priority. Refer to Table1.
Ifthedevicestatusindicatorashes,thenthedeviceisselectedinaman-machineinterfacesuchasthe
Bürkert Communicator software.
Table1: Device status indicator in accordance with NAMUR NE107, edition 2006-06-12
Colour
accordingto
NE107
Colourcode
(foraPLC)
Diagnosticsevent
accordingto
NE107
Meaning
Red 5 Failure, error or
fault
Due to a malfunction of the device or its periphery,
the measured values can be incorrect.
Orange 4 Check function Ongoingworkonthedevice(forexample,checking
the correct behaviour of the outputs by simulating
measurementvalues);theoutputsignalistemporarily
invalid(e.g.frozen).
Yellow 3 Outofspecication The ambient conditions or process conditions for the
device are outside the permitted ranges.
Device-internal diagnostics point to problems in the
device or with the process properties.
Blue 2 Maintenance
required
The device continues to measure but a function is
temporarily restricted.
→Do the required maintenance operation.
Green 1 - Diagnostics are active and no diagnostics event has
been generated.
White 0- Diagnostics are inactive
English

20
Technical data
Type 8098FLOWaveL
6 TECHNICAL DATA
6.1 Operating conditions
Ambienttemperature Depends on the liquid temperature (see Fig.9 or Fig.10)
• Device variant with
twoM20x1.5cable
glandsandone5-pinM12
connector
• –10°C...+70°C,iftheliquidtemperatureis–10°C...+80°C(seeFig.9)
• See Fig.9,iftheliquidtemperatureishigherthan+80°C
• Devicevariantwithtwo4-pin
M12 female connectors and
one5-pinM12connector
(Ethernetdevicevariant)
• –10°C...+55°C(seeFig.10)
Airhumidity <85%,noncondensing
Heightaboveseelevel max.2000m
Operatingconditions Continuous operation
Equipmentmobility Fixeddevice
Use Indoorandoutdoor
▶Protect the device against electromagnetic interference, ultraviolet rays
and,wheninstalledoutdoors,againsttheeectsofclimaticconditions.
Installationcategory CategoryIaccordingtoUL/EN61010-1
Degreeofpollution Degree2accordingtoUL/EN61010-1
IP-CodeaccordingtoIEC/
EN60529
IP651),IP671) if the following conditions are observed:
• The device must be wired.
• The cable glands must be tightened.
• The covers must be screwed tight.
• Unused cable glands must be sealed with the blind plugs provided.
The blind plugs are mounted upon delivery of the device.
• Unused M12 connectors must be protected by a screwed plug.
Protectiontypeaccordingto
NEMA2501)
4X if the following conditions are observed:
• The device must be wired.
• The cable glands must be tightened.
• The covers must be screwed tight.
• Unused cable glands must be sealed with the blind plugs provided.
The blind plugs are mounted upon delivery of the device.
• Unused M12 connectors must be protected by a screwed plug.
1)notevaluatedbyUL;onlyIP64isevaluatedbytheATEX/IECExnotied/certicationbody.
→ForthespecialoperatingconditionsofdeviceswithATEX/IECExcertication,refertotheATEX/IECEx
supplement for the device. The supplement is available at country.burkert.com.
English