Burkert 8030 User manual

Type 8030
INLINE Flowmeter
Operating Instructions
Bedienungsanleitung
Manuel d'utilisation
” (Fcs-Ural) . 
8 (351) 22-354-11
8 (351) 22-529-13
 Burkert -  “-- ”
(Fcs-Ural) . 
www.burkert-ural.ru 8 (351) 22-354-11
www.fcs-ural.ru 8 (351) 22-529-13

2
1. ABOUT THIS MANUAL ...........................................................3
2. INTENDED USE ..........................................................................5
3. BASIC SAFETY INFORMATION .........................................6
4. GENERAL INFORMATION .....................................................9
5. DESCRIPTION ..........................................................................10
6. TECHNICAL DATA ..................................................................13
7. INSTALLATION AND COMMISSIONING ..................... 19
8. MAINTENANCE ........................................................................ 30
9. ACCESSORIES ........................................................................32
10. PACKAGING, TRANSPORT ...............................................33
11. STORAGE ...................................................................................33
12. DISPOSAL OF THE DEVICE ............................................. 34
English

3
1. ABOUT THIS MANUAL
This manu al describes the entire life c ycle of the devi ce.
Please keep this manual in a safe place, accessible to all
users and any new owners.
This manual contains important safety information.
Failure to comply with these instructions can lead to
hazardous situations.
• This manual must be read and understood.
Symbols used
DANGER
Warns against an imminent danger.
• Failure to observe this warning can result in death or in
serious injury.
WARNING
Warns against a potentially dangerous situation.
• Failure to observe this warning can result in serious
injury or even death.
English 3

4
ATTENTION
Warns against a possible risk.
• Failure to observe this warning can result in substantial
or minor injuries.
NOTE
Warns against material damage.
• Failure to observe this warning may result in damage
to the device or system.
Indicates additional information, advice or
important recommendations.
refers to information contained in this manual or in
other documents.
Indicates a procedure to be carried out.
Definition of the word "device"
The word "device" used within this manual refers to the
flowmeter type 8030.
English

5
2. INTENDED USE
Use of the device that does not comply with the
instructions could present risks to people, nearby
installations and the environment.
• The 8030 flowmeter is intended exclusively to measure
flow rate in liquids.
• This device must be protected against electromagne-
tic interference, ultraviolet rays and, when installed
outdoors, the effects of climatic conditions.
• This device must be used in compliance with the
characteristics and commissioning and use conditions
specified in the contractual documents and in the user
manual.
• Requirements for the safe and proper operation of the
device are proper transport, storage and installation,
as well as careful operation and maintenance.
• Only use the device as intended.
Observe any existing restraints when the device is
exported.
English 5

6
3. BASIC SAFETY INFORMATION
This safety information does not take into account:
• any contingencies or occurences that may arise during
installation, use and maintenance of the devices.
• the local safety regulations that the operator must ensure
the staff in charge of installation and maintenance observe.
Danger due to high pressure in the installation.
Danger due to electrical voltage.
Danger due to high temperatures of the fluid.
Danger due to the nature of the fluid.
Various dangerous situations
• Prevent any unintentional power supply switch-on.
• Ensure that installation and maintenance work are
carried out by qualified, authorised personnel in
possession of the appropriate tools.
English

7
Various dangerous situations
• Guarantee a set or controlled restarting of the pro-
cess, after a power supply interruption.
• Use the device only if in perfect working order and
in compliance with the instructions provided in the
instruction manual..
• Observe the general technical rules when installing
and using the device.
• Do not use this device in explosive atmospheres.
• Do not use the device for the measurement of gas flow
rates.
• Do not use fluid that is incompatible with the materials
the device is made of.
• Do not use this device in an environment incompatible
with the materials it is made of.
• Do not subject the device to mechanical loads (e.g. by
placing objects on top of it or by using it as a step).
• Do not make any external modifications to the device. Do
not paint any part of the device.
English 7

8
NOTE
The device may be damaged by the fluid in contact
with.
• Systematically check the chemical compatibility of the
component materials of the device and the fluids likely
to come into contact with it (for example: alcohols,
strong or concentrated acids, aldehydes, alkaline
compounds, esters, aliphatic compounds, ketones,
halogenated aromatics or hydrocarbons, oxidants and
chlorinated agents).
NOTE
Elements / Components sensitive to electrostatic
discharges
• This device contains electronic components sensitive
to electrostatic discharges. They may be damaged
if they are touched by an electrostatically charged
person or object. In the worst case scenario, these
components are instantly destroyed or go out of order
as soon as they are activated.
• To minimise or even avoid all damage due to an elec-
trostatic discharge, take all the precautions described
in the EN 61340-5-1 and 5-2 norms.
• Also ensure that you do not touch any of the live elec-
trical components.
English

9
4. GENERAL INFORMATION
To contact the manufacturer of the device, use following
address:
Bürkert SAS
Rue du Giessen
BP 21
F-67220 TRIEMBACH-AU-VAL
The addresses of our international sales offices are avai-
lable on the internet at: www.burkert.com
Warranty conditions
The condition governing the legal warranty is the conforming
use of the device in observance of the operating conditions
specified in this manual.
Information on the Internet
You can find the user manuals and technical data sheets
regarding the type 8030 at: www.burkert.com
English 9

10
5. DESCRIPTION
Area of application
The 8030 flowmeter is intended to measure the flow rate of
neutral or slightly aggressive liquids free of solid particles.
Construction
The device is built with an SE30 electronic module and an
S030 fitting incorporating the measuring element. The device
can be mounted on any pipe from DN6 to DN65.
The electronic device can be removed without opening the
piping or stopping the process.
Depending on the version, the device has either one NPN
transistor output or two transistor outputs, NPN and PNP.
Electrical connection is made via a male fixed connector.
Measuring principle
The fluid flowing in the piping makes the paddle-wheel
turn. The sensor detects the rotation of the paddle-wheel
thus generating a signal which frequency f is proportional
to the flow rate Q, acc. to formula f = KxQ.
f = frequency in Hertz (Hz)
K = K factor of the S030 fitting used, in pulse/litre
Q = flow rate in litre/second
English

11
Description of the name plate
FLOW : SE30 / 8030
HALL 12-36 V DC
OPEN COLLECTOR PNP/NPN
S/N:59037
00423913 W45LG
Made in France
1
4
5
6
789
32
1. Type of sensor
2. Measured quantity
3. Type of the device
4. Supply voltage
5. Output data
6. Conformity logo
7. Manufacturing code
8. Serial number
9. Order code
Available versions of electronic
module SE30
All the electronic modules have to be connected via a male
fixed connector.
English 11

12
Version of elec-
tronic module SE30
Supply voltage
Output
Order code
Hall 12-36 V DC 2 transistors,
NPN and
PNP
423913
Hall Low
Power
energized via the
Bürkert transmitter
the flow sensor is
connected to
1 NPN
transistor 423914
Ordering codes of fitting S030 can be found within the
related data sheet: refer to the data sheet to select the
fitting appropriate to the process.
English

13
6. TECHNICAL DATA
Conditions of use
Ambient temperature
(operating)
-15 °C to +60 °C
Air humidity < 80%, non condensated
Protection rating IP65, female connector wired,
plugged and tightened
Conformity to standards and
directives
The device conforms to the EC directives through the
following standards:
• EMC: EN 61000-6-2, EN 61000-6-3
• Pressure: The S030 fitting complies with article 3 of §3
from 97/23/CE directive.
Acc. to pressure directive 97/23/CE, the fitting can only
be used in the following cases (depending on the max.
pressure, the DN of the pipe and the fluid):
Type of fluid Conditions
Fluid group 1 § 1.3.a only DN25
Fluid group 2 § 1.3.a DN  32
or DN > 32 and PNxDN 1000
Fluid group 1 § 1.3.b PNxDN  2000
English 13

14
Type of fluid Conditions
Fluid group 2 § 1.3.b DN200
General data
Pipe diameter DN6 to DN65
The appropriate diameter is deter-
mined using the flow rate / DN / fluid
velocity graphs.
Pressure class Depends on the material of the fitting
used and on the fluid temperature:
refer to the operating instructions of
the fitting used.
Fluid temperature
• with fitting S030 in
metal or PVDF
• with fitting S030
in PP
• with fitting S030 in
PVC
The fluid temperature may be restricted
by the fluid pressure: refer to the ope-
rating instructions of the fitting used.
• -15 to +100 °C
• 0 to +80 °C
• 0 to +50 °C
Type and data of the
fluid
refer to the operating instructions of
the fitting used.
English

15
Flow rate measuring
range 0,3 to 10 m/s
Accuracy, with standard
K factor
(0.5 % of the full scale + 2.5 % of
the measured value)*
Linearity   0,5 % of the full scale (10 m/s)*
Repeatability  0,4 % of the measured value*
* Determined in the following reference conditions: medium =
water, water and ambient temperatures 20 °C, min. upstream and
downstream distances respected, appropriate pipe dimensions
English 15

16
Table 1: Dimension H [mm] of the 8030 depending on
the DN of fitting S030
DN H with fitting
S030
H
06 95,5
08 95,5
15 100,5
20 98
25 98
32 102
40 105,5
50 112
65 112
32
40
66
44
54
9
Fig. 1: Dimensions [mm] of the SE30 electronic
module
English

17
Materials
Part Material
Housing, male fixed
connector PC
Female connector
type 2508 / screw /
seal
PA / Stainless steel / NBR
Fitting S030 refer to the operating instructions of the
fitting used.
Electrical data
Supply voltage
• Hall version
• Hall Low Power
version
• 12-36 V DC, filtered and
regulated
• 12-36 V DC, via transmitter
the device is connected to
Dielectric strength 2300 VAC
Current consumption
• Hall version
• Hall Low Power
version
• 30 mA max.
• 0,8 mA max.
Protection against
polarity reversal
yes
English 17

18
Protection against spike
voltages
yes
Protection against short
circuits
yes
Transistor output (Hall
version)
pulse output, NPN and PNP,
open collector, max. 100 mA,
frequency up to 300 Hz, duty
cycle 1/2 ±10%
NPN output: 0,2-36 VDC
PNP output: supply voltage
Transistor output (Hall
Low Power version)
pulse output, NPN, open
collector, max. 10 mA,
frequency up to 300 Hz, duty
cycle 1/2 ±10%
Electrical connection
Type of connector cable type
female connector
type 2508 (supplied),
ordering code 438811
• shielded, max. 50 m
• 5 to 8 mm in diameter
• wires between 0,25 and
1,5 mm2 in cross section
English

19
7. INSTALLATION AND
COMMISSIONING
Safety instructions
DANGER
Risk of injury due to high pressure in the installation.
• Stop the circulation of fluid, cut off the pressure
and drain the pipe before loosening the process
connections.
Risk of injury due to high fluid temperatures.
• Use safety gloves to handle the device.
• Stop the circulation of fluid and drain the pipe before
loosening the process connections.
Risk of injury due to the nature of the fluid.
• Respect the prevailing regulations on accident pre-
vention and safety relating to the use of hazardous
products.
English 19

20
DANGER
Risk of injury due to electrical voltage.
• Shut down and isolate the electrical power source
before carrying out work on the system.
• Observe all applicable accident protection and safety
regulations for electrical equipment.
WARNING
Risk of injury due to non-conforming installation.
• The electrical and fluid installation can only be carried
out by qualified and skilled staff with the appropriate
tools.
• Observe mounting instructions of the fitting.
Risk of injury due to an uncontrolled restart.
• Ensure that the restart of the installation is controlled
after any interventions on it.
English