Burley Stroller Kit Instruction Manual

Burley Stroller Kit Owner’s Instruction
and Safety Manual
For D’Lite,
™Solo, ™Encore, ™Cub, ™
Honeybee,
™and Tailwagon
stroller kit

2 |BURLEY STROLLER KIT OWNER’S INSTRUCTION AND SAFETY MANUAL
Congratulations!
By purchasing the Burley Stroller Kit, you’ve increased the fun
and excitement that you and your family can have with your
Burley trailer.
Please go to www.burley.com or contact us at [phone]
or [e-mail] to register your warranty information.
Safety Guidelines
1. Consult your child trailer manual for trailer safety guidelines.
2. Always use the handle bar tether.
3. When placing children or cargo into the trailer, keep the load
centered and in front of the axle.
4. Always set the parking brake before releasing the handle.
Make sure the parking brake is properly adjusted and
working before use, especially after changing the tires or
removing the wheels.
5. This product was designed for use on surfaces that are meant
for walking. Do not use it on stairs, escalators or other uneven
surfaces. Never use it with inline or roller skates.
6. Never leave your children unattended.
WARNING! FAILURE TO OBSERVE ALL OF THE SAFETY GUIDELINES IN THIS MANUAL
AND YOUR BURLEY TRAILER MANUAL COULD RESULT IN AN ACCIDENT
AND SERIOUS INJURY OR DEATH.
IMPORTANT: IT IS vERY IMpORTANT FOR YOU TO FAMILIARIzE YOURSELF
WITH YOUR STROLLER ATTACHMENT BY READINg THIS MANUAL BEFORE
USE. IF YOU HAvE ANY qUESTIONS, pLEASE CONTACT US.

1. Remove tow bar from trailer.
2. Remove nut and bolt from tow bar end. Discard bolt and lock
nut. Safety strap and D-ring will be re-installed. Figure 2
3. Slide stroller kit onto tow bar. Figure 3
4. Place D-ring and safety strap on supplied 6mm x 50mm bolt.
Line up holes in stroller kit, tow bar and flex connector and
install bolt. Secure with nut. Install two shorter bolts through
pivot assembly side and secure with nuts. Figure 4
Tools Required:
(2) 10mm open end wrenches
(1) 25mm (or 1”) wrench
(1) 5mm hex wrench
Installation
BURLEY STROLLER KIT OWNER’S INSTRUCTION AND SAFETY MANUAL | 3

4 |BURLEY STROLLER KIT OWNER’S INSTRUCTION AND SAFETY MANUAL
5. Around handlebar center, slide tether strap end through small
loop on other end of strap and tighten securely. Photo 1
6. Slide tow bar into trailer receptacles and line up front
tow bar hole with rear receptacle hole. Insert retaining pin
through both holes and lock retaining hoop securely. Figure 5
7. Test tracking adjustment by pushing trailer. Trailer should
roll straight.
To Adjust Tracking
1. Tighten knob to secure stroller wheel in “Stroll” position.
See Figure 6
2. Loosen bolt using 5mm hex wrench. Figure 6
3. Turn bushing using 25 mm (or 1”) wrench so that stroller
wheel is vertical when viewed from front.
4. Fine tune as necessary, so that trailer rolls straight.
5. Tighten bolt.
Figure 6
Photo 1

BURLEY STROLLER KIT OWNER’S INSTRUCTION AND SAFETY MANUAL | 5
To Convert from Strolling to Trailering
1. Engage parking brake and tighten knob to secure stroller
wheel in “Bike” position. Figure 7
2. Line up rear tow bar hole with rear receptacle hole. Insert
retaining pin through both holes and lock retaining
hoop securely. Figure 8
3. Re-install the tow bar and hitch on the bike.
Maintenance
lLubricate stroller wheel assembly twice a year for normal
use, or monthly if used in wet or salty conditions.
lInspect handle, receivers, parking brake, and wheel monthly.
lContact Burley to replace any damaged parts.
WARNING! WHEN CONvERTINg THIS ATTACHMENT FOR TRAILERINg, MAKE SURE
THAT STROLLER WHEEL IS IN pROpER pOSITION BEFORE ATTACHINg
TRAILER TO YOUR BICYCLE. DO NOT USE THIS pRODUCT WITHOUT
RETAININg pIN AND SAFETY STRAp pROpERLY INSTALLED. FAILURE
TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL AND YOUR TRAILER
MANUAL CAN CAUSE AN ACCIDENT RESULTINg IN SERIOUS INJURY.

BURLEY DESIGN, LLC
Eugene, OR 97402
PH 541.687.1644 800.311.5294 FAX [phone]
[e-mail] •www.burley.com
Copyright © 2007 by Burley Design LLC
Burley is a registered trademark of Burley Design LLC
Rev 01/11. 170053 manual stroller kit 08 r1
Burley Accessory Limited Warranty
Burley accessories are warranted from date of purchase against defects in materials and
workmanship under normal use and service. Burley will repair or replace parts it determines
to be defective for a period of five years. The Burley accessory owner must present the
accessory for repair at place of purchase, with an original sales receipt or similar proof of
purchase. This warranty applies only to the original owner and is nontransferable. Burley
can not be responsible for failure due to improper assembly, modification of parts or
instructions, neglect, abuse, accident, and/or normal wear. The warranty does not cover
any accessory used for rental, competition, or commercial use. Burley neither assumes nor
authorizes any person to assume any other liability in connection with this Burley product,
and there are no oral agreements or warranties collateral to or affecting this agreement.
This warranty gives you specific legal rights. You may also have other rights which vary by
state or country.