Burnside P350 User manual

P350 desktop mobile phone
Burnside Telecom Limited
Burnside House, Isington, Alton
GU34 4PP, United Kingdom
BURNSIDE
www.burnsidetelecom.com
quick start guide
Tel: [phone]
Fax: [phone]
Email: [email protected]
This quick start guide will help you to set up, switch on and begin using your
P350 desktop mobile phone. For further information, please refer to the full
user guide supplied with the product.
Setting up
Unlock the transit switch
When shipped, your P350 is locked for
transit to prevent it from powering on
accidentally. You need to unlock the
phone before it will operate.
1 On the underside of the P350, locate
the recessed switch near to where
the handset cable attaches.
2 Slide the switch towards the rear of
the P350 unit.
The P350 will not switch on at this
stage.
Locked
position
Unlocked
position
Install your SIM card
Note: Ensure the T350 is switched off.
1 On the rear panel of the P350, carefully
swing open the SIM slot door.
2 Orientate your SIM card with its contacts
facing downwards and the notched cor-
ner facing towards the slot.
3 Push the SIM card into the slot until it
clicks into place. Close the door.
Note: To remove the SIM card, press it
inwards to release and partially eject it.
Then slide it out of the slot.
Transit
switch
D
E
F
7
M4
Redial
89
4
M3
Mute
56
12
M2
M1
Names
Register
SMS
Menu
Select
Mailbox
Clear
Call
3
0
M5
Handsfree
+
#
Wireless
Modules
by Siemens
BURNSIDE
Menu
Press to
display
the setup
menu.
Handsfree
Press to begin
handsfree dialling or
to answer an incom-
ing call without pick-
ing up the handset.
Memory buttons
Use to store regular
contacts for quick
dialling.
Arrow keys
Use to
control
menu
options.
Select
Use to
choose
menu
options.
The standby screen
When the P350 is not involved in a call or any other operation, it will display a
screen similar to the one below which indicates the network name as well as the
time, date, signal strength and other status icons.

Attach the power adapter
1 Attach the connector from the power adapter to
the socket on the far right of the rear panel.
2 Plug the power adapter main body into a
nearby mains outlet and ensure that the outlet
is switch on.
D
E
F
7
M4
Redial
89
4
M3
Mute
56
12
M2
M1
Names
Register
SMS
Menu
Select
Mailbox
Clear
Call
3
0
M5
Handsfree
+
#
Wireless
Modules
by Siemens
BURNSIDE
Attach the handset cable
1 Locate the handset and the supplied cable.
2 Connect one end of the cable to the socket at the base of the handset and the
other end to the socket in the left side of the P350 unit.
Handset cable
Attach the antenna
1 Align the supplied antenna (or another suitable
GSM antenna) with the circular connector on the
far left of the rear panel.
2 Attach the antenna and twist the connector
collar clockwise until it is finger-tight - do not
overtighten.
3 In use, the antenna should always be vertical.
The supplied antenna has a hinge so that you
can position it correctly.
Prepare the power adapter
The power adapter is supplied with at least one snap-on plug to suit the mains
power sockets used in your location. Before using the power adapter, you need to
attach the snap-on plug, if it has not already been fitted.
1 Locate the power adapter main body and the appropriate snap-on plug (if it has
not already been fitted to the main body).
2 Orientate the snap-on plug so that its
underside connection slots are aligned
with the two metal blades of the
adapter main body, as shown here:
3 Slide the plug into the adapter main
body and press it firmly into place until
you hear a click (as it snaps into posi-
tion).
Switch on
1 On the rear panel, press and hold the red button
until the display responds, then release.
Notes
To switch off, press and hold the red button until the
display goes blank.
During normal use, the P350 should only be switched
on and off using the red button. Use the transit switch
only once the unit has been turned off.
If the transit switch is inadvertently moved to the locked position, the P350 will im-
mediately shut off or enter a charging state if the power adapter is connected.
Red
power
button