Buyers Products Company LT10 User manual

Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • buyersproducts.com
3. After determining the position of the uprights,
mark center of the two holes in each upright base
on the trailer deck.
WARNING! Check under the trailer for locations
of brake lines and electrical wiring etc., before
drilling any holes. Any damage to trailer during
installation is installer’s full responsibility.
1 3004208 1 Post, Vertical Nonlocking, Trimmer Rack
2 0204300 2 Plug, Plastic Finish, 1" Sq Tube
3 3004083 6 Guide, Spring
4 3004084 6 Spring, Torsion Trimmer Rack
5 3005286 3 Hook, Grip Pivot
6 - 6 Screw, HHC 5/16-18 x 2-3/4" Gr 5 Zn
7 - 6 Nut, Nylock 5/16-18 Zn
8 3004091 1 Tube, Vertical, Locking, Welded
9 3004082 3 Hook, Pivot
10 3004090 1 Lock, Trimmer Rack, Finished
11 - 2 Washer, Flat 1/2" SAE Zn
12 - 2 Nut, Nylock 1/2-13 Zn
13 3004466 1 Angle, Top Connecting, LT10
14 - 14 Washer, Flat 3/8" USS Zn
15 - 4 Screw, HHC 3/8-16 x 2 Gr 5 Zp
16 - 4 Screw, HHC 3/8-16 x 2-1/2 Gr 5 Zp
17 - 8 Nut, Nylock 3/8-16 x 7/16 Zn
Installation Instructions
LT10 Lockable Trimmer Rack
for Utility Landscape Trailers
—continued on other side
Important!
Before you begin installing:
1. Read and understand these instructions
completely.
2. Verify that you have received all the parts
listed in the bill of materials.
Tools Required:
•Two 9/16" wrenches and/or sockets
•Electric drill
•13/32" drill bit
•Carpenter’s square
•Tape measure
•Two C-clamps
•Hack saw
CAUTION:
Always wear safety glasses when using power tools.
1. Clamp the locking and nonlocking uprights to
the trailer side rail approximately 28" to 34" apart
with the base of the upright on the trailer floor.
The locking upright may be assembled on the
left or right of the nonlocking upright. Verify the
uprights are square to the trailer deck in both
directions with a carpenter’s square. Note: If bent
shaft trimmers are used, the uprights need to be
mounted closer together than if straight shaft
trimmers are used.
2. Assemble a line trimmer to the rack to verify the
distance between the uprights is correct for the
model of trimmer you wish to hold. The large hook on
the nonlocking upright should engage the trimmer’s
grip and the smaller hook on the locking upright
should engage the shaft of the trimmer. Do not clamp
on or near the throttle trigger of the trimmer. With
the trimmer assembled in position, verify that the lock
assembly can rotate freely over the trimmer shaft.
ITEM PART NO. QTY. DESCRIPTION
Bill of Materials

Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • buyersproducts.com
3004410 Rev. B
WARRANTY
Buyers Products warrants all truck/trailer hardware manufactured or
distributed by it, to be free from defects in material and workman-
ship for a period of one year from date of shipment. Parts must be
properly installed and used under normal conditions. Any product
which has been altered, including modification, misuse, accident or
lack of maintenance will not be considered under warranty. Normal
wear is excluded. The sole responsibility of Buyers Products under
this warranty is limited to repairing or replacing any part or parts
which are returned, prepaid, and are found to be defective by Buyers
Products. Authorization from Buyers Products must be obtained
before returning any part. No charges for transportation or labor per-
formed on Buyers’ products will be allowed under this warranty.
4. Remove the uprights from the trailer and use
a 13/32" drill bit to drill four holes in your trailer
deck as marked.
5. Assemble the uprights to the trailer with
four 3/8-16 x 2-1/2" cap screws, eight 3/8" flat
washers and four 3/8-16 nylock nuts. Do not
tighten screws at this time!
6. Clamp the two uprights to the rail of the
trailer. Make sure the uprights are square to the
rail and the deck of the trailer with a square.
7. With the uprights clamped into position drill
a 13/32" hole through the center of each upright
and the trailer rail.
8. Fasten each upright to the trailer rail with
a 3/8-16 x 2" cap screw, two 3/8" flat washers,
and a 3/8-16 nylock nut. Tighten all six screws.
9. Loosely assemble the top connecting angle
to an upright using hardware supplied and hold
horizontally. Mark the angle on the outside of
the second upright. Remove and cut off excess
material.
10. Drill a 13/32" hole in the center of the angle’s
web 1/2" from the end of the angle.
11. Assemble top connecting angle using two
3/8-16 x 2" cap screws, two 3/8" flat washers
and two 3/8-16 nylock nuts and tighten.