Buyers Products Company LT20 User manual

Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • buyersproducts.com
Installation Instructions
LT20 Backpack Blower Rack
for Utility Landscape Trailers
—continued on other side
Holds most backpack blowers. Locks with a long
shackle padlock.
STIHL
®
BR-340 and BR-420 owners must use rack part no. LT22.
Important!
Before you begin installing:
1. Read and understand these instructions
completely.
2. Verify that you have received all the parts
listed in the bill of materials.
CAUTION:
Always wear safety glasses when using power tools.
Utility Trailer Installation Instructions
Tools Required:
•Two 9/16" Wrenches and/or Sockets
•Electric Drill
•13/32" Drill Bit
•Carpenters Square
1. Clamp the blower rack to the trailer side rail with
the base of the upright on the trailer floor. Verify the
rack is square to the trailer deck in both directions
with a carpenter’s square.
2. After determining the position of the rack, mark
center of the two holes in the base on the trailer deck.
WARNING! Check for locations of brake lines and
electrical wiring etc., before drilling any holes.
Any damage to trailer during installation is the
installer’s sole responsibility.
3. Remove the rack from the trailer and use a 13/32"
drill bit to drill two holes in your trailer deck as marked.
4. Assemble the rack to the trailer with two 3/8-16
x 2-1/2" cap screws, four 3/8" flat washers and two
3/8-16 nylock nuts. Do not tighten screws at this time!
5. Clamp the blower rack to the rail of the trailer.
Make sure the rack is square to the rail and the deck
of the trailer with a square.
6. With the rack clamped into position drill a 13/32"
hole through the center of 1" tube and the trailer rail.
7. Fasten rack to the trailer rail with a 3/8-16 x 2" cap
screw, two 3/8" flat washers, and a 3/8-16 nylock nut.
Tighten all three screws at this time.
1 3000065 1 Weldment, Blower Rack
2 TS31 1 Strap, Rubber Tarp 31"
3 9225 2 S-Hook, 2-1/2" Zn, Tarp Strap
4 - 2 Washer, Flat 3/8 USS Zn
5 - 2 Screw, Hex Head Lag, 3/8 x 2, Zn
ITEM PART NO. QTY. DESCRIPTION
Bill of Materials

Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • buyersproducts.com
3000689 Rev. A
Warranty Information
Buyers Products warrants all truck/trailer hardware manufactured or distributed by it, to be free from defects in
material and workmanship for a period of one year from date of shipment. Parts must be properly installed and used
under normal conditions. Any product which has been altered, including modification, misuse, accident or lack of main-
tenance will not be considered under warranty. Normal wear is excluded. The sole responsibility of Buyers Products
under this warranty is limited to repairing or replacing any part or parts which are returned, prepaid, and are found to
be defective by Buyers Products. Authorization from Buyers Products must be obtained before returning any part. No
charges for transportation or labor performed on Buyers’ products will be allowed under this warranty.
Enclosed Trailer Installation Instructions
Tools and Materials Required:
•9/16" Wrench or Socket
•Electric Drill
•13/32" & 1/4" Drill Bits
•Hack Saw
•3/4" Plywood Shim Strips
•Shim Screws
1. To maximize floor space in your trailer cut 18" off
the bottom of the blower rack with a hack saw.
2. Drill two 13/32" holes through the center of the
1" square tube at least 12" apart.
3. In order to mount this rack to an enclosed trailer,
you must first add 3/4" plywood shim strips to the
walls. These shim strips must be attached to at least
two wall support studs with suitable fasteners. If you
don’t know what kind or length of fastener to use
contact your trailer dealer or manufacturer for their
recommendation.
4. Hold the blower rack vertical against the shims
and mark the position of the two 13/32" holes.
WARNING! Check for locations of brake lines and
electrical wiring etc., before drilling any holes.
Any damage to trailer during installation is the
installer’s sole responsibility.
5. Drill two 1/4" pilot holes in the positions just
marked for the 3/8" lag screws. Be extremely careful
not to drill through the outside trailer wall.
6. Fasten the blower rack to the trailer wall with the
two 3/8" x 2" lag screws and two 3/8” flat washers
supplied.
1 3000065 1 Weldment, Blower Rack
2 TS31 1 Strap, Rubber Tarp 31"
3 9225 2 S-Hook, 2-1/2" Zn, Tarp Strap
4 - 6 Washer, Flat 3/8 USS Zn
5 - 2 Screw, HHC 3/8-16 x 2-1/2 Gr 5 Zp
6 - 1 Screw, HHC 3/8-16 x 2 Gr 5 Zp
7 - 3 Nut, Nylock 3/8-16 x 7/16 Zn
ITEM PART NO. QTY. DESCRIPTION
Bill of Materials