Buyers Products Company LT35 User manual

Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • buyersproducts.com
Installation Instructions
LT35 Hand Tool Rack
for Utility Landscape Trailers
—continued on other side
1 3004207 1 Post, Hand Tool Rack
2 3004165 2 Angle, Tool Holder
3 3004167 12 Grommet, Rubber, for 2" hole
4 - 4 Screw, HHC 5/16-18 x 1-1/2 Gr 5 Zn
5 - 4 Nut, Nylock 5/16-18 Zn
6 - 6 Washer, Flat 3/8 USS Zn
7 - 1 Screw, HHC 3/8-16 x 2 Gr 5 Zp
8 - 2 Screw, HHC 3/8-16 x 2-1/2 Gr 5 Zp
9 - 3 Nut, Nylock 3/8-16 x 7/16 Zn
10 - 1 Plug, Plastic Finish, 1" Square Tube
ITEM PART NO. QTY. DESCRIPTION
Bill of Materials
Important!
Before you begin installing:
1. Read and understand these instructions
completely.
2. Verify that you have received all the parts
listed in the bill of materials.
Tools Required:
•Two 9/16" wrenches and/or sockets
•Two 1/2" wrenches and/or sockets
•Electric drill
•13/32” Drill bit
•Carpenter’s square
•C-clamp
CAUTION:
Always wear safety glasses when using power tools.
1. Clamp the post of the hand tool rack to the
trailer side rail. The hand tool rack uses 4" x 23"
of the trailer floor space and the post is centered
in this space. Position the hand tool rack such
that the lawn mowers or other equipment will
not damage the hand tool handles. Verify that
the post is square to the trailer deck in both direc-
tions with a carpenter’s square.
2. After determining the position of the post
mark center of the two holes in each upright base
on the trailer deck.
WARNING! Check under the trailer for locations
of brake lines and electrical wiring etc., before
drilling any holes. Any damage to trailer during
installation is installer’s full responsibility.
3. Remove the post from the trailer and use a
13/32" drill bit to drill two holes in your trailer
floor as marked.

Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • buyersproducts.com
3004399 Rev. A
Warranty Information
Buyers Products warrants all truck/trailer hardware
manufactured or distributed by it, to be free from
defects in material and workmanship for a period of
one year from date of shipment. Parts must be pro-
perly installed and used under normal conditions.
Any product which has been altered, including modi-
fication, misuse, accident or lack of maintenance will
not be considered under warranty. Normal wear is
excluded. The sole responsibility of Buyers Products
under this warranty is limited to repairing or replac-
ing any part or parts which are returned, prepaid, and
are found to be defective by Buyers Products.
Authorization from Buyers Products must be obtained
before returning any part. No charges for transporta-
tion or labor performed on Buyers’ products will be
allowed under this warranty.
7. Fasten the post to the trailer rail with a 3/8-16
x 2" cap screw, two 3/8" flat washers, and a 3/8-16
nylock nut. Tighten all three screws.
8. Assemble the tool holder angle brackets to the
post using four 5/16-18 cap screws and nylock
nuts. The tool holder angles should be above the
trailer floor so that the handles of the tools rest
on the trailer floor.
9. Assemble the twelve grommets into the two
inch holes in the tool holder angles.
4. Assemble the post to the trailer with two
3/8-16 x 2-1/2" cap screws, four 3/8" flat washers
and two 3/8-16 nylock nuts. Do not tighten screws
at this time!
5. Clamp the post to the rail of the trailer. Make
sure the post is square to the rail and the deck of
the trailer with a square.
6. With the post clamped into position, drill a
13/32” hole through the center of the post and
the trailer rail.