Buyers 8883000 User manual

www.buyersproducts.com
Phone [phone]
Fax [phone]
8883000 Rear Observation System
With Night Vision Camera
1

2
Table of Contents
What's in the Box? ...........................................................3
Introduction ......................................................................4
Safety Information ........................................................ 5-6
Before Beginning Installation........................................ 7-8
Installation Guide........................................................ 9-10
Installing Monitor...................................................... 11-12
Installation Diagram........................................................13
Remote Control Diagram................................................13
Monitor Specifications ...................................................14
Camera Specifications ...................................................15
Positioning......................................................................16
Troubleshooting..............................................................17
Warranty .........................................................................18
Disclaimer ......................................................................19

3
What’s in the Box?
• (1) Color CCD Infrared Weather Resistant Camera
• (1) 7" TFT LCD Color Monitor with Standard U-Bracket
Mount, Pedestal Mount, Flush Mount
• (1) Sun Shade
• (1) 65' Camera Cable
• (1) Power Harness
• (1) Remote Control
• (1) Hardware Bag

4
Congratulations on purchasing a Rear Observation
System With Night Vision Camera. With this manual you
will be able to properly install and operate the unit.
The Rear Observation System is intended to be
installed as a supplement aid to your standard rear
view mirror that already exists in your vehicle. The Rear
Observation System should not be used as a substitute
for the standard rear view mirror or for any other mirror
that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive
a motor vehicle equipped with a TV viewer or screen
located in any location that is visible, directly or indirectly,
to the driver while operating the vehicle.
Introduction
Please read all of the installation instructions carefully
before installing the product. Improper installation will
void manufacturer’s warranty.

5
USAGE
• The Rear Observation System is designed to help the
driver safely detect people and/or objects helping to
avoid damage or injury. However, you the driver, must
use it properly. Use of this system is not a substitute for
safe, proper or legal driving.
• Never back up while looking at the monitor alone. You
should always check behind and around the vehicle
when backing up, in the same way as you would if the
vehicle did not have the Rear Observation System. If
you back up while looking only at the monitor, you may
cause damage or injury. Always back up slowly.
• The Rear Observation System is not intended for use
during extensive back-up maneuvers or backing into
cross traffic or pedestrian walkways.
• Please, always remember, the area displayed by the
Rear Observation System is limited. It does not display
the entire panorama that is behind you.
Safety Information
Please read the entire manual and follow the
instructions and warnings carefully. Failure to do so
can cause serious damage and/or injury, including loss
of life. Be sure to obey all applicable local traffic and
motor vehicle regulations as it pertains to this product.
Improper installation will void manufacturer’s warranty.

6
• Electric shock or product malfunction may occur if this
product is installed incorrectly.
• Use this product within the voltage range specified.
Failure to do so can cause electric shock or product
malfunction.
• Take special care when cleaning the monitor.
• Make sure to firmly affix the product before use.
• If smoke or a burning smell is detected, disconnect the
system immediately.
• Where the power cable may touch a metal case,
cover the cable with a friction tape. A short circuit or
disconnected wire may cause a fire.
• While installing the Rear View System be careful with
the wire positioning in order to avoid wire damage.
• The Rear View System should only be used when the
vehicle is in reverse.
• Do not install the monitor where it may obstruct drivers
view or obstruct an air bag device.
• Dropping the unit may cause possible mechanical/
electrical failure.
Safety Information

7
Before drilling please check that no cable or wiring is on
the other side of the wall. Please clamp all wires securely
to reduce the possibility of them being damaged
while vehicle is in use. Keep all cables away from hot
or moving parts and components causing electrical
interference.
We recommend doing a bench test before installation to
insure that all components are working properly (pg 13).
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a
0.8" (20mm) hole should be drilled for passing camera
cable through vehicles walls. Install split grommets
where applicable.
Step 3: Once all cables and wiring have been properly
routed, perform a system function test by temporarily
connecting the system. If the system seems to not be
operating properly see troubleshooting (pg 17).
Before Beginning Installation

Before Beginning Installation
8
Cable
1. Be sure to route the cable carefully. The camera
cable uses aircraft grade connectors which means the
camera cable can be exposed to all weather elements.
Do not run the cable over sharp edges, do not kink
the cable and keep away from HOT and rotating parts,
such as but not limited to, exhaust systems and drive
shafts.
2. Fasten and secure all excess cable.
Monitor
1. To Attach the Pedestal mount to the dashboard or to
the headliner/roof using self-tapping screws and/or the
adhesive pad.
2. Attach monitor to mount, and adjust mounting angle
to allow optimum driver viewing comfort. (see figure on
page 11)

Installation Guide
9
The Power Harness
• To power the system connect the power (RED) +12VDC
wire to ignition power and the ground (BLACK) wire to
chassis ground.
• These are the only wires needed to power the entire
system and all the cameras. Each camera can be seen at
any time by simply pressing the power button and using
the V1/2 button to toggle.
• The three positive trigger wires (CH1, CH2, CH3) each
represent one channel and will turn on their channel when
the trigger wire is energized with +12VDC.
• Camera 3 is the designated backup channel. To have
the backup camera come on when you go into reverse,
connect the CH3 wire to reverse power (or any power
source that comes on only in reverse).
• The other channels can similarly be triggered (i.e. side
cameras can be triggered by the turn signals etc.)
• To automatically have camera and monitor turn ON
when vehicle activates, simply twist CH3 positive trigger
+12VDC to Red Power line +12VDC and wire to ignition
power.
Note: This setup will disable the menu in channel 3. To access the
menu simply move to channel 1 or 2 and all the changes will apply to
channel 3.
Note: When the channel 3 wire is active it will have precedence over
the other triggers. Therefore, if you wish to use multiple triggers, do
not attach the blue trigger to constant power.

Installation Guide
10
• Audio: There is audio on channels 2 and 3. On CH3 the
trigger wire must be energized (+12VDC) to activate the
audio. On CH2 the audio is always on.
• Grid-lines: The grid-lines are also carried through the CH3
wire. To use the grid-lines for reversing, connect the CH3
wire to a reverse power. Grid lines can be deactivated in
the menu. Menu > PARKSET > Toggle ON or Toggle OFF
• There is a built-in voltage regulator for our systems which
can handle 10-30 Volts DC.
Note: The camera and monitor can always be activated by manually
pushing the power button on monitor. This is in addition to utilizing the
positive triggers.
Note: If connecting power directly to battery, the camera is always
ON and therefore can drain battery. Therefore it is recommended to
connect power to an ignition switched accessory power source.

Standard U-Bracket Monitor Installation
11
1. Remove the thumb and allen screw from the monitor
then remove monitor. Place bracket in desired location
and fasten down with 3 screws. (See below pictures)
2.
Using the thumb and allen screws put the monitor into the
bracket, adjust angle, and lock it. (See below pictures)
3. Finish installation. The adjustable angle is 30° forward or
backward. (See below pictures)

12
Optional Monitor Installations
Pedestal Mount
1. Using screws, secure pedestal bracket. (See below
pictures)
Flush Mount
2. Secondly, slide the metal buckle piece on the top of
the pedestal bracket into the notch on the back of the
monitor. Move the bracket to the desired location and
tighten. (See below pictures)
self-tapping screw
or machine screw

Installation Diagram
Remote Control
1. Power 2. Switch over 3. “+”
4. Menu 5. “-” 6. Mode select
13
4 Pin Connection
CH1
CH2
CH3
(optional camera)
(optional camera)
Connect to CAM3
Connect to CAM1
Connect to CAM2
(CH3 normal image)

14
Monitor Specifications
7" monitor
1.“-”
2.Menu
3.“+”
4.Power
5.Channel 1
6.Channel 2
7.Mode
8.Remote control
window
9.A/V input connector
10.Bracket knobs
Screen size 7 inch
Aspect ratio 16:9
Resolution 800x480
Brightness 500cdm
Audio & Video 2 Ways video input (3 Ways video input optional)
2 Ways audio input 1 AV input (optional)
Video System PAL & NTSC automatically
Voltage 12V-24V
Power Consumption 5W
Impact Rating 5G
Language Multi-language
OSD Menu Display Menu, Brightness, Color, Contrast
Adjustable
Built-in speaker Yes
Bracket accessories U Type Bracket, Pedestal Bracket, Recessed
Mount
Sunshade Removable
Operation Temperature -4°F – 176°F

Camera Specifications
Sensor 1/4 SONY Color CCD
Resolution (PAL) 582(H)×510(V) pixels
TV Line 420 TV Line
Lens 2.8mm
View angle 120°
Sync System Internal
Infrared distance 45ft (18pcs Infrared IR)
Min illumination 0 Lux (LED ON)
S/N Ratio 65dB
Video output 1Vp-p 75Ω
Water Resistant IP69K
Impact Rating 20G Vibration/10G shock
Microphone & Heater YES
Operation Temperature -4°F – 167°F
15

16
Positioning

17
Troubleshooting
Monitor Displays Blue Screen & Displays "No Signal"
• Do a hard reset, unplug all cables and power cables,
leave out for 1 minute, and then re-connect.
• Check to ensure that the connection to the camera is tight.
• Verify camera cable is plugged into camera port
• Verify that the trigger on power harness is put to power
+12VDC.
• If the problem still persists, verify that alternate ports
work. If alternate ports do not work, remove trigger wire
from +12VDC and select alternate channels.
Monitor Will Not Power-Up (no backlight on power)
• Check fuse
• Check +12VDC connection
• Check ground connection
• Try power and ground direct to battery
No Image On Screen
• Verify camera is on correct camera input
• Verify cable is connected to monitor
• Verify camera is connected to cable
• Connect known working camera and cable to monitor.
• Verify trigger source is supplying power
Audio on Camera
• Verify chosen camera has audio
• Verify volume setting
• Confirm that the CH3 trigger is connected to +12VDC

18
Warranty
Two Year Warranty
Buyers Products Company, Inc. warrants this product against material de-
fects for a period of two years from date of purchase. We reserve the right
to repair or replace any such defective unit at our sole discretion. Buyers
Products Company, Inc. is not responsible for a defect in the system as
a result of mis-use, improper installation, damage or mishandling of the
electronic components. Buyers Products Company, Inc. is not responsible
for consequential damages of any kind.
This warranty is void if: defects in materials or workmanship or damages
result from repairs or alterations which have been made or attempted by
others or the unauthorized use of nonconforming parts; the damage is due
to normal wear and tear, this damage is due to abuse, improper mainte-
nance, neglect or accident; or the damage is due to use of the Buyers
Products Company, Inc. system after partial failure or use with improper
accessories.
Warranty Performance
DURING THE ABOVE WARRANTY PERIOD, SHOULD YOUR Buyers Prod-
ucts Company PRODUCT EXHIBIT A DEFECT IN MATERIAL OR WORK-
MANSHIP, SUCH DEFECT WILL BE REPAIRED WHEN THE COMPLETE
Buyers Products Company, INC. PRODUCT IS RE-TURNED, POSTAGE
PREPAID AND INSURED, TO Buyers Products Company, INC. OTHER
THAN THE POSTAGE AND INSURANCE REQUIREMENT, NO CHARGE
WILL BE MADE FOR REPAIRS COVERED BY THIS WARRANTY.
Warranty Disclaimers
NO WARRANTY, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, OTH-
ER THE ABOVE. WARRANTY IS MADE WITH REGARD TO THIS Buyers
Products Company, INC. Buyers Products Company, INC. DISCLAIMS
ANY IMPLIED WARRANTY OR MERCHANT-ABILITY OR FITNESS FOR A
PARTICULAR USE OR PURPOSE AND ALL OTHER WARRANTIES IN NO
EVENT SHALL Buyers Products Company. INC. LIABLE FOR ANY INCI-
DENTAL, SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES OR FOR
ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS AL-
LEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF,
OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY
CLAIMS FOR LOSS OF PROFITS.

19
Disclaimer
Buyers Products Company and/or its affiliates does not guarantee
or promise that the user of our systems will not be in/part of an
accident or other-wise not collide with an object and/or person. Our
systems are not a substitute for careful and cautious driving or for
the consistent adherence to all applicable traffic laws and motor
vehicle safety regulations. The Buyers Products Company products
are not a substitute for rear view mirrors or for any other motor vehi-
cle equipment mandated by law. Our camera systems have a limited
field of vision and do not provide a comprehensive view of the rear
or side area of the vehicle. Always make sure to look around your
vehicle and use your mirrors to confirm rearward clearance and that
your vehicle can maneuver safely. Buyers Products Company and/
or its affiliates shall have no responsibility or liability for damage
and/or injury resulting from accidents occurring with vehicles having
some of Buyers Products Company products installed and Buyers
Products Company and/or its affiliates, the manufacturer, distrib-
utor and seller shall not be liable for any in-jury, loss or damage,
incidental or consequential, arising out of the use or intended use of
the product. In no event shall Buyers Products Company and/or its
affiliates have any liability for any losses (whether direct or indirect,
in contract, tort or otherwise) incurred in connection with the sys-
tems, including but not limited to damaged property, personal injury
and/or loss of life. Neither shall Buyers Products Company and/or
its affiliates have any responsibility for any decision, action or inac-
tion taken by any person in reliance on Buyers Products Company
systems, or for any delays, inaccuracies and/or errors in connection
with our systems functions.

20
If you have questions about this product, contact:
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Email: [email protected]
www.buyersproducts.com
IN NO EVENT SHALL SELLER OR MANUFACTURER
BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL
DAMAGES OF ANY NATURE, OR LOSSES OR
EXPENSES RESULTING FROM ANY DEFECTIVE
PRODUCT OR THE USE OF ANY PRODUCT.
20 8883000INST_A