Buyers SaltDogg PRO2500 Series User manual

1
www.buyersproducts.com
Phone [phone]
Fax [phone]
Installation Instructions
—continued inside
PRO2500 &PRO2500CH Series SaltDogg®
Electric Drive Poly Hopper Spreader
2.5 cubic yards
U.S. Patent 9,562,333
Table of Contents
General Information ....................................................................1
Safety Precautions ......................................................................1
Installation Instructions ........................................................... 1-3
Spreader Operation ....................................................................4
Spreader Maintenance ............................................................ 4-5
Warranty Information ..................................................................5
Repair Parts & Drawings ......................................................... 5-8
General Information
Overall Length: 116.5 inches
Overall Width: 48 inches
Overall Height: 44.3 inches
Empty Weight: 986 lbs.
Capacity Struck: 2.5 cu. yd.
Vehicle Requirements
Trucks with minimum GVWR 13,000 lbs. (8 ft. bed), 150 AMP or
higher alternator is recommended.
Average Material Weights
This spreader is restricted to the use of dry, free-flowing salt,
sand, and sand/salt mix. Do not run other materials through the
spreader.
Materials to use Weight (pounds per cubic yard)
Fine Salt-Dry 2,250
Coarse Salt-Dry 1,431
Sand/Salt up to 50/50 Mix-Dry 2,700
Note: To calculate the total spreader weight (including ice
control material), add the empty spreader weight plus the ice
control material and spreader accessories.
CAUTION
Do not overload vehicle beyond the vehicle’s GVWR or GAWR.
Check vehicle's load rating certification sticker for maximum
vehicle capacity.
WARNING
Improper installation and operation could cause personal
injury, and/or property damage. Observe the following Safety
Precautions before, during and after operating this spreader. By
following these precautions and common sense, possible injury
to persons and potential damage to this machine may be avoided.
Safety Precautions
1. Read the entire Installation Instructions before operating this
spreader.
2. Read and understand all safety decals on the spreader
before operating.
3. Check to make sure all safety guards are securely mounted
into place before operating this spreader.
4. Verify that all personnel are clear of the spreader spray area
before starting or operating this spreader.
5. Do not over-load your vehicle beyond payload limits. If there
are any questions, contact the vehicle manufacturer.
6. Do not adjust, clean, lubricate or unclog material jambs
without first turning off the spreader.
7. Do not climb on or in the spreader during operation. Do not
ride on the spreader while the vehicle is in motion.
8. Make sure the spreader is securely fastened to the vehicle in
accordance with this manual.
9. Do not operate a spreader that is in need of maintenance or
repairs.
10. Do not operate the spreader while ill, tired, or under the
influence of alcohol or drugs.
11. Batteries normally produce explosive gases which can
cause personal injury. Always disconnect the battery before
removing or replacing electrical components.
12. Do not leave unused material in hopper. Material can
freeze or solidify, causing spreader to not work properly, and/or
damage the unit. Empty and clean after each use.
Installation Instructions
1. Mounting the Spreader onto the Vehicle
A. Remove the tailgate from the vehicle (if equipped) as well as
any other object which will interfere with the spreader.
B. Check truck’s bed for all kinds of sharp debris or foreign
objects. They can cut and seriously damage poly hopper.
C. Remove chute, hardware kit from inside spreader. If spreader
has been used make sure there is no material left in the hopper.
D. Lift spreader using all tie downs (Fig. 1), or using fork lift.
Lower spreader into the truck bed.

2
www.buyersproducts.com
Phone [phone]
Fax [phone]
E. Center the spreader on the truck with the chute mount about
14" to the rear edge of the bed.
F. Chute assembly. Assembly chute to hopper following
instructions shown in Fig. 2 – Fig. 3
G. Slide spreader forward or backwards to make sure that chute
doesn’t interfere with any part of the truck. Remove one pin and
rotate chute as shown in Fig. 4. Make sure that chute doesn’t hit
any part of the truck.
H. Measure the distance from the front of the truck bed to the
front of the hoppers front legs. Fabricate spacer to fit between
front of the spreader and front of the bed using 2 x 6 boards
and install it between the spreader and truck bed front wall as
shown in Fig. 5
I. In addition, secure spreader using four ratchet straps. Tighten
straps evenly. (Fig 5.1)
USE ALL TIE-DOWNS
TO LIFT SPREADER
Fig. 1
SLIDE CHUTE ON
CHUTE ATTACHMENT
ALIGN HOLES AND
SECURE CHUTE USING
PINS #3033174
Fig. 2
#3033174
Fig. 3
ROTATE CHUTE
Fig. 4
SPACER
BED WIDTH
FIT TO BED
10.0"
20.0"
Fig. 5
Fig. 5.1

3
www.buyersproducts.com
Phone [phone]
Fax [phone]
E. Connect the 2-pin connector on the power cable to the control
box mating connector.
F. Connect wire harness single connectors to control box
connectors.
G. Connect fuse connector to the fuse terminal or ignition switch
(5 AMP max).
H. Lay out a path for the power cable to the battery, use quick ties
to secure power cable. DO NOT CONNECT TO BATTERY AT THIS
TIME!
I. Lay out path for wire harness to the rear of the vehicle. Stay
clear of the exhaust system. Excess heat can damage the wire
harnesses. Use quick ties to secure harness to underbody.
J. Connect the wire harness to the motors and vibrator. Make sure
wire colors on wire harness match colors on the motor.
K. Thoroughly clean battery terminals. Make sure battery terminals
have no tarnish or corrosion. DO NOT CONNECT WIRE HARNESS
TO DAMAGED OR CORRODED TERMINALS! IT MAY RESULT IN
OVERHEATING, LOST POWER AND POTENTIAL CONTROLLER
DAMAGE! Install the circuit breaker within 12" from the battery.
Connect red wire from cable 3035935 and battery cable 3001379
to circuit breaker according to the breaker markings. Connect
the power cable and battery cable directly to the battery. Make
sure connection to battery terminals is good and tight. Loose
connection to battery terminals will result in sparking, overheating
and possible battery damage!
L. Insure all functions of the controller are working properly.
M. Observe auger/ chain moving in proper direction. If direction is
wrong reverse wires between Motor and Wire Harness.
N. Optional spot light (5 AMP max) can be installed on spreader.
Use utility light kit part number 3018009. Remove cap from single
white wire. Connect light to this wire and the trucks frames known
ground (negative).
2. Control Box and Vehicle Wiring Harness Installation
Note: Make sure you have connected the proper wire color. This
is a wire ground electrical system! No Connections to truck’s
frame or body allowed!
Note: Always disconnect battery before attempting to install
electrical components on your vehicle
A. Mount the controller in a convenient location in the truck cab.
It is recommended not to mount the controller directly in front of
heat vents. Allow ample air space around controller
CAUTION
Inspect straps and hardware after each time spreader is loaded.
Tighten straps and hardware if necessary.
CAUTION
Do not mount controller in the way of air bag deployment!
WARNING
Important! Do not use ratchet straps or tailgate latch exclusively!
Always use spacer!
WARNING
Do not drill holes into fuel tanks, fuel lines, through electrical
wiring, etc that may be damaged by drilling. To insure good
performance of your spreader, check the condition of truck’s
electrical system. Using digital voltmeter, check alternator and
battery voltage. With engine running and head lights and heater
fan ON good voltage reading should fall between 13.0 and 15.3
volts. If voltage reading falls out of this range, check and adjust
your electric system.
IMPORTANT
Make sure all wires securely attached to vehicle or spreader. Use
wire ties and/or wire clamps to attach wires. All excess wires
must be rolled into bundles and attached to vehicle or spreader
B. Route both wire harnesses into truck cab through firewall (it
maybe necessary to drill holes). Insulate hole to avoid water leaks.
C. Insure no wires are nicked or damaged during installation.
D. Connect the 4-pin connector on the wire harness to the control
box 4-pin connector.
3016934
3030628
0203700
3035935
CB150PB
3001379
BATTERY POSITIVE
BATTERY NEGATIVE
CONNECT TO FUSE
OR WIRE IN FUSE PANEL,
CONTROLLED BY
IGNITION SWITCH

4
www.buyersproducts.com
Phone [phone]
Fax [phone]
Loosen Screws, Rotate
Shields to Adjust
Spray Pattern
Unscrew Bolts, Slide
Lower Chute Up or Down
Into Desired Position,
Reinstall & Tighten Bolts
Spreader MaterialsSpreader Operation
1. PRO2500 is equipped with a dual independent speed
controller. To start spreader, press “POWER” switch. Switch
will be illuminated. Auger/ chain and spinner will start rotating.
Auger and spinner can be adjusted independently.
2. To activate vibrator press “VIBRATOR” switch, vibrator switch
will illuminate. Vibrator can operate continuously for 30 min max
with 15 min brakes to avoid overheating.
3. To stop spreader press “ON-OFF” switch again.
4. PRO2500 controller is equipped with electronic overload and
current spike protection. Controller is not serviceable.
Controller has two LED lights: “ERROR” and “FLASH NUMBER”.
If there is a problem the ERROR LED will illuminate and FLASH
NUMBER LED will give a series of flashes. Count the number of
flashes and refer to the troubleshooting guide provided with the
controller. Additionally you can go online for the troubleshooting
codes at https://snowdogg.com/media/3802/3026671_A.pdf
5. Spreading pattern can be controlled by repositioning of the
baffles on the chute as shown in Fig. 6. Chute heights can be
adjusted to accommodate different vehicle heights (Fig.6).
The density of materials that can be loaded into the spreader varies
and therefore so will the amount of a given material that can be
carried by the spreader before the maximum load rating is reached.
1. Ensure that the spreader is securely mounted to the vehicle
and that the top screen is installed and secured in the hopper.
2. Remove the tarp, if used.
3. Determine the amount of material that you can safely
transport using your vehicles GVWR/GAWR and the following
table on page 1.
4. Fill the spreader evenly with your material, making sure not to
fill past the top of the hopper.
Fig. 6
6. Check the Feed Chain tension periodically. To check the tension,
measure in 21"-25" from the rear edge of the gear box mount. Push
up on the chain with your hand. The conveyor chain should lift up
2"-3" off the conveyor chain guide or cross angles (Fig. 7).
Feed Chain Rear of Sill Extension
2" - 3"
21" - 25"
Fig. 7
WARNING
Never attempt to lift spreader with material in hopper!
WARNING
Never leave material in hopper for extended period of time.
Material can freeze, solidify and seriously damage the spreader
IMPORTANT
Only use dry salt, sand, sand/salt, or cinder/salt mixes in the
spreader. Other materials could cause damage to the machine.
IMPORTANT
When filling the spreader, do not exceed the gross-vehicle-weight
rating (GVWR) or gross-axle-weight rating (GAWR).
IMPORTANT
Overfilling the hopper could damage the spreader & your vehicle.
Spreader Maintenance
1. Wash spreader after every use. Make sure no material is left
under auger/ chain and/or inside trough.
2. Inspect and retighten fasteners after every 5-7 hours of operation.
3. Lubricate bearings every 7-10 hours of operation using
general automotive grease.
4. Inspect terminals/connectors every time you disconnect
spreader from wire harness. Apply thin layer of dielectric grease
on terminals. If any tarnish/corrosion is found, clean terminals
and apply dielectric grease.
5. Use dielectric grease on all electrical connectors before an
electrical connection is made or after connector is disconnected
6. Empty the spreader of all ice control materials when not in
use. Wash out the spreader to prevent material builds up.
7. It is recommended to cover spreader with the tarp during
storage periods.
End of Season Maintenance
1. Wash spreader. Make sure no material or residue is left in and
outside the hopper.
2. Lubricate bearing using general automotive grease.
3. Inspect wire harness, connectors for broken insulation, missing
components. Replace if necessary.
4. Apply dielectric grease on all electrical connectors.
5. Store hopper indoors, in a dry, cool place.
6. Remove controller from truck. Store controller indoors, in a dry
cool place.
7. Inspect wire near connectors. Check for broken or missing
insulation. Check for tarnished or corroded wires. Trim corroded
wires and replace connectors if necessary

5
www.buyersproducts.com
Phone [phone]
Fax [phone]
Summer Storage
1. Apply dielectric grease or similar protective compound on all
electrical connectors & protect them with caps before storage.
2. Disconnect and remove speed controller from vehicle and
store it in dry and cool place. Protect controller from excessive
heat and moisture.
3. Clean hopper and trough from all kinds of debris.
4. Remove, thoroughly lubricate and reinstall trough bearing.
5. Protect hopper from excessive temperatures during
summer storage.
Accessories
PRO2500 is supplied with tarp 3030857. To insure proper tarp
operation, attach tarp to all hopper posts as shown below. Tarp
can be replaced by poly lids (kit #3034577 sold separately).
Repair Parts - Chute Assembly Part # 3031475
Bill of Materials
ITEM PART NO. QTY. DESCRIPTION
1 3030868 1 UPPER CHUTE WELDMENT
2 3030930 1 CHUTE OUTER, POLY
3 3030908 1 MOTOR MOUNT CHUTE
4 3030907 1 MOTOR 12 VDC, .5 HP SPINNER
5 FCS038016075SS 8 SCREW, HHC-3/8-16 X 3/4 SST
6 3012393 1 SPINNER, 14" POLY CW
7 3025065 1 BUSHING STRAIN RELIEF
8 FWF025063007SS 4 WASHER, FLAT 1/4 SAE SS
9 FCS025020075SS 2 SCREW, CAP 1/4-20 X 3/4 SST
10 3008549 2 SCREW,HEXHD CAP 1/4-20X.5 SST
11 3030927 2 SHIELD, CHUTE
12 3031755 3 PLASTIC HEAD THUMB SCREW 3/8-16X3/4 SST
13 3007115 4 WASHER, FLAT 3/8 X 1.5 X.048 SST
14 FWL038069009SS 4 WASHER, LOCK RHS-3/8 SST
15 3007113 1 PIN, CLEVIS, 5/16 X 2-1/2, .141 HOLE ZN
16 3014994 1 PIN,COTTER,1/8IN X 1IN SST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CAB SIDE LABEL
SECURE TARP ON
SPREADER ATTACHING
BUNGEE CORD TO ALL POSTS
PRO2500 SPREADER WARRANTY INFORMATION
This warranty replaces all previous warranties and no employee of this company is authorized to extend additional warranties, or agreements, or
implications not explicitly covered herein.
Buyers Products Company warrants all parts of the product to be free from defects in material and workmanship for a period of two (2) years. Parts
must be properly installed and used under normal conditions. Normal wear is excluded.
Any part, which has been altered, including modifications, misuse, accident, or lack of maintenance will not be considered under this warranty.
The sole responsibility of Buyers Products Company under this warranty is limited to repairing or replacing any part(s), which are returned, prepaid,
30 days after such defect is discovered, and returned part(s) are found to be defective by Buyers Products Company.
Authorization from Buyers Products Company must be obtained before returning any part. The following information must accompany defective
parts returned to Buyers Products Company: RMA #, spreader model, serial number, date installed, and distributor from whom purchased.
Buyers Products Company shall not be liable for damage arising out of failure of any unit to operate properly, or failure, or delay in work, or for any
consequential damages. No charges for transportation or labor performed on any part will be allowed under this warranty.
Connector Kit Drawing
WIRE HARNESS TO CHUTE
CONNECTOR KIT #3020301
WIRE HARNESS TO
AUGER/CHAIN GEAR MOTOR
CONNECTOR KIT #3024738
WIRE HARNESS TO
CONTROLLER CONNECTOR
KIT #3017233

6
www.buyersproducts.com
Phone [phone]
Fax [phone]
Repair Parts - PRO2500 Auger Hopper Assembly
Bill of Materials
ITEM PART NO. QTY. DESCRIPTION
1 3030763 1 HOPPER PRO2500
2
3032999 1TROUGH WELDMENT PRO2500
3 3007115 12 WASHER, FLAT 3/8 X 1.5 X.048 SST
4
FWL038069009SS 16 WASHER, LOCK RHS-3/8 SST
5
FCS038016075SS 12 SCREW, HHC-3/8-16 X 3/4 SST
6
1410200 1 BEARING, FLANGED 1-1/8"
7
3001255 4 NUT, HEX FLNG-3/8-16 SST
8
3033003 1 SPACER, GEAR MOTOR
9 3024575 1 GEAR MOTOR CONVEYOR 12 VDC
10
3033660 1 AUGER PRO 5.25 VARIABLE LH
11
3033663 1SLEEVE, AUGER ADAPTER
12
FCS038016100SS 8 SCREW, HHC 3/8-16 X 1 304 SST
13
FWF038100007SS 4 WASHER, FLAT 3/8 USS SST
14
FNE038016044SS 20 NUT, NYLOCK 3/8-16 X 7/16 SST
15
3001250 1 SCREW, HHC-1/2-13 X 3 SST
16
FNE050013053SS 1 NUT, NYLOCK 1/2-13 SS
17 3033070 1 BRACKET BEARING FRONT
18
9240086 1 BEARING, 1-1/4 FLANGE 2 HOLE
19
FCB037516100SS 4 BOLT, 3/8-16 X 1 CARRIAGE SST
20
3022220 4TIE-DOWN WELDMENT
21
3030854 2 CROSS MEMBER
22
3005140 12 SCREW, HH1/2-13X 3.5, GR 5 ZN
23
FWF050106010 12 WASHER, FLAT 1/2" SAE ZINC
24 FNE050013053 12 NUT, NYLOCK 1/2-13 ZINC
25
3030863 1INVERTED VEE, PRO2500
26
3039179 1BRACKET VIBRATOR
27
3007416 1 VIBRATOR 200 LBS 12 VDC
28
3031176 1PLATE WELDMENT, VIBRATOR
29
FCS038016150SS 4 SCREW, HX HD CAP 3/8-16 X 1-1/2 SST
ITEM PART NO. QTY. DESCRIPTION
30 3031169 1 SHROUD
31
FWF025063007SS 2 WASHER, FLAT 1/4 SAE SS
32 FCS025020075SS 2 SCREW, CAP 1/4-20 X 3/4 SST
33
3033165 2 STUD THREADED 5/16-18 X 2.5 SST
34
3006719 2 NUT, HEX FLANGE - 5/16-18 SS
35
3031203 1 MOUNT CONNECTORS
36
3007522 7 SCREW, SHEET MTL #12x1.0 HEX WASHER HD SS'f
37
3031276 2 CLIP ATTACHMENT, CONNECTOR DEUTSCH
38 3032591 1 DECAL, DANGER, MOVING CONVEYOR/AUGER
39
3032595 1 DECAL, CAUTION, MOUNTING
40
3033076 1CHUTE ATTACHMENT
41
3012144 4 BOLT, CARRIAGE, 5/16-18 X 1 SST
42
FNE031018034SS 4 NUT, NYLOCK 5/16-18 SS
43
3035346 1 RIGHT ANGLE JUNCTION BLOCK
44
3035357 2 SCREW SOCKET HD, RND 8-32X 1.50 SST
45
3035358 2 NUT, NYLOCK 8-32 SST, BLACK OXIDE
46 800 2 GREASE FITTING, 1/4 STD
47
3035347 2 GREASE FITTING 1 MTU BE 1/8 NPT STRAIGHT
48
3035742 2 BUSHING SNAP THICK PANEL
49
3035344 2 GREASE FITTING 1 MTU BE 1/4-28 MALE STRAIGHT
50
3035359 1GREASE TUBE REAR BEARING AUGER
51
3036016 1GREASE TUBE FRONT BEARING AUGER
52
4375 3 CLAMP, HOSE .4375, 9/32 HOLE
53 3035854 1 LABEL PATENT
54
3033172 1 DECAL CONNECTION
1
2
3
4
5
6 7 8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40 41 42
43
44 45
46
47
48
49
50
51
52
53
54

7
www.buyersproducts.com
Phone [phone]
Fax [phone]
Repair Parts - PRO2500CH Chain Hopper Assembly
Bill of Materials
ITEM PART NO. Q TY. DESCRIPTION
1 3030763 1 HOPPER PRO2500
2
3033164 1 WIPER BRACKET
3 3035269 1 WIPER BELT, FRONT
4
3007522 12 SCREW, SHEET MTL #12x1.0 HEX WASHER HD SS'
5
3027772 1 TROUGH CHAIN PRO500
6
3007115 12 WASHER, FLAT 3/8 X 1.5 X.048 SST
7
FWL038069009SS 16 WASHER, LOCK RHS-3/8 SST
8
3013821 1 GEAR MOTOR CONVEYOR 12 VDC
9
FCS038016100SS 8 SCREW, HHC 3/8-16 X 1 304 SST
10 1410200 1 BEARING, FLANGED 1-1/8"
11
3031483 2 BOLT, 3/8-16 X 1 CARRIAGE SHORT NECK SST
12
FNE038016044SS 14 NUT, NYLOCK 3/8-16 X 7/16 SST
13
KS402 2 KEY, 1/4 X 1/4X2
14
1410250 2 SPROCKET, 6 TOOTH PINTLE CHAIN
15
1401100P 1 CHAIN ASSY D662 122 LINKS
16
3008571 1SHAFT IDLER, ASSEMBLY
17
1411001 2 BEARING, IDLER TAKE UP
18 3023046 2BOLT, WELDED TAKE UP
19
3023022 2SPRING CHAIN TENSION
20
3031199 2TAKE-UP NUT WELDMENT
21
FNH063011054SS 2 NUT, HH 5/8-11 X 17/32 HIGH SST
22
3031195 1 CHAIN COVER
23
FWL025050006SS 4 WASHER, 1/4 IN. SPRING LOCK SST
24
FCS025020075SS 6 SCREW, CAP 1/4-20 X 3/4 SST
25 1410241 1 WIPER BELT, HOPPER
26
FWF025063007SS 7 WASHER, FLAT 1/4 SAE SS
27
3008549 5 SCREW,HEXHD CAP 1/4-20X.5 SST
28
FNE025020031SS 5 NUT, NYLON INSERT 1/4-20 SST
29
3022220 4TIE-DOWN WELDMENT
30
3030854 2 CROSS MEMBER
31
3005140 12 SCREW, HH1/2-13 x 3.5, GR 5 ZN
32 FWF050106010 12 WASHER, FLAT 1/2" SAE ZINC
33
FNE050013053 12 NUT, NYLOCK 1/2-13 ZINC
34
3030863 1INVERTED VEE, PRO2500
35
3039179 1BRACKET VIBRATOR
ITEM PART NO. Q TY. DESCRIPTION
36 3007416 1 VIBRATOR 200 LBS 12 VDC
37
3031176 1PLATE WELDMENT, VIBRATOR
38 FCS038016150SS 4 SCREW, HX HD CAP 3/8-16 X 1-1/2 SST
39
3035346 1 RIGHT ANGLE JUNCTION BLOCK
40
800 3 GREASE FITTING, 1/4 STD
41
3035357 2 SCREW SOCKET HD, RND 8-32X 1.50 SST
42
3035358 2 NUT, NYLOCK 8-32 SST, BLACK OXIDE
43
3035347 3 GREASE FITTING 1 MTU BE 1/8 NPT STRAIGHT
44
3035344 1 GREASE FITTING 1 MTU BE 1/4-28 MALE STRAIGHT
45 3035345 2 GREASE FITTING 1 MTU BE 1/4-28 MALE 90 DEGREE
46
3035348 1 GREASE HOSE REAR BEARING
47
3036051 1 GREASE HOSE FRONT DR SIDE
48
3036052 1 GREASE HOSE FRONT PS SIDE
49
5000 3 HOSE CLAMP, .375 DIA
50
3031169 1 SHROUD
51
3031203 1 MOUNT CONNECTORS
52 3031276 2 CLIP ATTACHMENT, CONNECTOR DEUTSCH
53
3033076 1CHUTE ATTACHMENT
54 3012144 4 BOLT, CARRIAGE, 5/16-18 X 1 SST
55 FNE031018034SS 4 NUT, NYLOCK 5/16-18 SS
56
1499035 2LABEL, WARNING 3
57 1499030 1 LABEL, CAUTION 1 (PAYLOAD)
58
3032591 1 DECAL, DANGER, MOVING CONVEYOR/AUGER
59 3032593 1 DECAL, DANGER, CONVEYOR
60
3032595 1 DECAL, CAUTION, MOUNTING
61 3033165 2 STUD THREADED 5/16-18 X 2.5 SST
62
3033172 1 DECAL CONNECTION
63 3006719 2 NUT, HEX FLANGE - 5/16-18 SS
64
FCS038016075SS 12 SCREW, HHC-3/8-16 X 3/4 SST
1
2
3
4
5
6
7
8
9
10 11
12
13
14
15
16
17
18
19
20
21
22
23
24
25 26 27
28
29 30
31 3233
34
35
36
37
38
39 40
41 42
43 44
45
46
47
48
49
50
51
52
53
54
55
56
57 58
59
60
61
62
63
64

8
www.buyersproducts.com
Phone [phone]
Fax [phone]
3036329_C
Repair Parts - PRO2500CH SpreaderRepair Parts - PRO2500 Spreader
Bill of Materials Bill of Materials
ITEM PART NO. QTY. DESCRIPTION
1 3033301 1 HOPPER ASSEMBLY PRO2500
2 3031475 1 CHUTE SWING ADJ
3 3030853 1 TOP SCREEN PRO2500
4 3031797 1 HARDWARE KIT PRO2500
5 3016934 1 CONTROLLER SPEED 12 VDC, 60 AMP
6 3030628 1 WIRE HARNESS MAIN
7 3035938 1 KIT POWER CABLE REPLACES 3016943
8 3035935 1 POWER CORD
9 3001379 1 CABLE, SCH BATTERY 14 IN. (RED)
10 CB150PB 1 BREAKER, 150 AMP.
11 0203700 1 WIRE ASSEMBLY, 36 LONG
12 14965051 1 HOLD DOWN KIT, SPREADER (4 STRAPS)
13 3030857 1 TARP PRO2500
14 3033174 2 PIN, CHUTE ATTACHMENT
15 66050 4 SNAPPER PIN, 1/4 X 2, YLW ZINC
16 3036015 1 LABEL SERIAL NUMBER PRO2500
ITEM PART NO. QTY. DESCRIPTION
1 3030766 1 HOPPER ASSEMBLY PRO2500
2 3031475 1 CHUTE SWING ADJ
3 3030853 1 TOP SCREEN PRO2500
4 3031797 1 HARDWARE KIT PRO2500
5 3016934 1 CONTROLLER SPEED 12 VDC, 60 AMP
6 3030628 1 WIRE HARNESS MAIN
7 3035938 1 KIT POWER CABLE REPLACES 3016943
8 3035935 1 POWER CORD
9 3001379 1 CABLE, SCH BATTERY 14 IN. (RED)
10 CB150PB 1 BREAKER, 150 AMP.
11 0203700 1 WIRE ASSEMBLY, 36 LONG
12 14965051 1 HOLD DOWN KIT, SPREADER (4 STRAPS) BLA
13 3030857 1 TARP PRO2500
14 3033174 2 PIN, CHUTE ATTACHMENT
15 66050 4 SNAPPER PIN, 1/4X2, YLWZINC
16 3036015 1 LABEL SERIAL NUMBER PRO2500
2
3
15
16
1
5
6
8
9 10
11
12
13
14
1
3
15
5
6
8
9
10
11
12
13
14
2
16