BWI Eagle AIR-EAGLE XLT PLUS 465AN/D-5000-DC Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT PLUS
Analog & Digital 900 MHz RF Receiver
MODEL 465AN/D-5000-DC
DESCRIPTION
The AIR-EAGLE XLT PLUS, MODEL 465AN/D-5000-DC Is an RF receiver
capable of receiving one analog or voltage input signal and one dry-
contact input signal from an analog / digital output transmitter. The
transmitter and receiver combine to create a long range radio
frequency system that monitors and operates hazardous or hard-to-
reach electrical apparatus from safe, convenient locations of up to a
mile away. (Or longer with optional antennas) This unit is user-
programmable for up to seven network frequencies to allow multiple
systems to operate simultaneously in the same area without
interference.
INSTALLATION
1. Mount the AIR-EAGLE XLT PLUS RECEIVER in a convenient location
2. Install wiring to terminal strip.
3. Connect DC power and control to the proper terminals in your control
circuit.
TERMINAL STRIP WIRING
TER1 (LEFT BLOCK)
TER2 (RIGHT BLOCK)
1
(-) 9-36VDC Input
1
Analog Output (-)
2
(+) 9-36VDC Input
2
Analog Output (+)
3
(+) Voltage Output
4
N/O Relay
5
C Relay
6
N/C Relay
7
N/O Relay –2nd Pole
8
C Relay –2nd Pole
9
N/C Relay –2nd Pole
10
Open Drain Output (not used)
Note #1 –Output type MUST be selected for the terminal strip wiring to
take effect! (See OUTPUT OPTIONS & FREQUENCY SET-UP)
(SIMILAR MODEL PICTURED)
Dimensions (with mounting plate) 6.3” L x 4.8” W x 2.3” H
CONTROLS & INDICATORS
POWER LED
Illuminates GREEN when powered on
OUTPUT
FAULT LED
Used in 4-20mA mode only –Illuminates RED when
current loop open

AIR-EAGLE®XLT PLUS
Analog & Digital 900 MHz RF Receiver
MODEL 465AN/D-5000-DC
OUTPUT OPTIONS & FREQUENCY SET-UP
This receiver is factory set with an analog output of 0-24mA selected and
to operate onfrequency #1. If you wish to change the default settings,
follow the instructions using the table below:
1) Remove power from unit
2) Remove top cover.
3) Select desired output option and/or frequency using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
OUTPUT CONFIGURATION
SEL1
SW1 & 2
OUTPUT TYPE
SW1
SW2
0-24mA Output (default)
OPEN
OPEN
0-20mA Output
CLOSED
OPEN
4-20mA Output
OPEN
CLOSED
Voltage Output
CLOSED
CLOSED
SEL1
SW3 & 4
VOLTAGE TYPE / LINK LOSS
OPEN
CLOSED
SW3
0-10V Output (default)
0-5VDC Output
SW4
Link Loss 4mA (default)
Link Loss 20mA
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
SPECIFICATIONS
Outputs
One 4-20mA or voltage output (0-5 or 0-10 VDC)
One DPDT 2amps @120VAC or 30VDC relay output
Fuse Protected
2 amp slow-blow
Safety Timer
15 seconds
DC Input
9-36 VDC
Enclosure
Polycarbonate NEMA 4X
Frequency
900MHz Spread Spectrum
Channels
7 Independent Network Frequencies
Receiving Range
Up to 25 miles line of sight with optional
antennas (see accessories)
Operating Temperature
-40oF to +185oF
APPROVALS
United States (FCC)
OUR-9XTEND
Canada (IC)
4214A-9XTEND
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main)
465AN/D-5002-DC
Standard Antenna (Included):
900MHz Portable Antenna (For distances up
to 1 mile*)
49-1103
Optional Antennas and Accessories:
900MHz Omni Directional Antenna (For
distances up to 5 miles*)
49-3101
900MHz 13dB Yagi Antenna
Long Range Operation (For distances up to
10 miles*)
49-3102
Flex Coax Cable w/Connectors
49-4000-XX
(XX = # of Feet)
* = Line of Sight
DIMENSIONS

AIR-EAGLE®XLT PLUS
Analog & Digital 900 MHz RF Receiver
MODEL 465AN/D-5000-DC
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly
used and installed, will be free from defects in material and workmanship
for a period of 1 year after date of purchase. Said warranty to include the
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improperinstallation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply onlyto the original purchaser of the equipment, and
last only for as long as such purchasercontinues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eaglemakes no express warranties beyond
those stated here. BWI disclaims without limitation, implied warranties of
merchantability and fitnessfor a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss during shipping and is
responsible forthe shipping costs incurred.
DOCUMENT DATE: 03/02/2019 / PRODUCT REV. 2
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com