BWI Eagle 461-8000-AC User manual

AIR-EAGLE XLT PLUS
461-8000-AC
900 MHz RF Receiver
Document Date: 11/10/2022
Product Rev: 1

461-8000-AC
1
WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free
from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to
include the repair or replacement of defective equipment. This warranty does not cover damage due to
external causes, including accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. This limited
warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of
the equipment, and last only for as long as such purchaser continues to own the equipment. This warranty
replaces all other warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express warranties beyond
those stated here. BWI disclaims without limitation, implied warranties of merchantability and fitness for a
particular purpose. Some jurisdictions do not allow the exclusion of implied warranties so this limitation
may not apply to you. To obtain warranty service, contact BWI Eagle for a return material authorization.
When returning equipment to BWI Eagle, the customer assumes the risk of damage or loss during
shipping and is responsible for the shipping costs incurred.
SIGNAL RANGE
Max range statements are estimates based on a clear line of sight with few interferences. Actual range will
vary based on transmitting power, orientation of transmitter and receiver, height of transmitting and
receiving antennas, weather conditions, electronic interference, terrain, and physical obstacles, including
but not limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills, mountains).
WIRELESS STOP, ASTOP, and E-STOP SYSTEMS
Wireless E-STOP systems should never be considered a primary life-saving device.
At least one hard-wired switch must be available in the event the wireless system is
not operational. Failure to comply may result in serious injury or death to personnel
and damage to equipment.
Wireless STOP and ASTOP transmitters are not failsafe emergency stop controls.
They are NOT to be used as a life-saving device. They are designed for wireless
control of equipment or vehicle remote operation. Failure to use as intended may
result in serious injury or death to personnel and damage to equipment.

461-8000-AC
2
INTRODUCTION
The Air-Eagle XLT Plus is an RF system designed for extra-long range wireless remote control of
electrical apparatus in a variety of industrial applications. Systems can consist of any number of receivers
and handheld or contact input transmitters working together to create a long-range radio frequency
system that operates hazardous or hart-to-reach equipment from safe, convenient locations.
Eight user selectable frequencies allow multiple systems to be used in the same area without
interference.
This receiver is equipped with four independent relays that can switch 5 amps @ 120VAC or 30VDC. The
relays are user programmable for momentary or toggle/latching operation and can be directly interfaced
with the customer's equipment or P.L.C. It is capable of receiving remote signals from an Air-Eagle XLT
Plus transmitter up to 5000 feet away. Longer ranges can be achieved with external antennas (See
ACCESSORIES section). The Air-Eagle XLT Plus receiver utilizes spread-spectrum technology and
provides the utmost in security and reliability.
SERIES FEATURE
The “461” series of receivers feature built-in repeating capability. They will listen for all transmissions from
the control transmitter, perform commands if necessary and pass all commands on to any receiver within
range to help propagate communication over widespread areas.
INSTALLATION
1. DISCONNECT power from all equipment before proceeding with installation.
2. Mount the receiver in a convenient location.
3. Install relay control wiring to the terminal strip. (See TERMINAL STRIP WIRING section.)
4. Attach rubber duck antenna or coax from external antenna to connector on side of enclosure.
5. Connect supplied power input cable to your external power source.

461-8000-AC
3
TERMINAL STRIP WIRING
Terminal 1
100-250 VAC Power Input
Terminal 2
100-250 VAC Power Input
Terminal 3
CH1 Dry Contact Input (Common)
Not used on this model
Terminal 4
CH1 Dry Contact Input
Terminal 5
CH2 Dry Contact Input (Common)
Terminal 6
CH2 Dry Contact Input
Terminal 7
N/O Relay 1
Terminal 8
C Relay 1
Terminal 9
N/C Relay 1
Terminal 10
N/O Relay 2
Terminal 11
C Relay 2
Terminal 12
N/C Relay 2
Terminal 13
N/O Relay 3
Terminal 14
C Relay 3
Terminal 15
N/C Relay 3
Terminal 16
N/O Relay 4
Terminal 17
C Relay 4
Terminal 18
N/C Relay 4
RELAY OPERATION
Relays energize and de-energize based on commands received from the transmitter. See below for relay
mode configuration for this receiver.
Transmitter Button Pressed
or Input Activated
Receiver Relay Action
1
Relay 1 energizes, maintained momentary
2
Relay 2 energizes, maintained momentary
3
Relay 3 energizes, maintained momentary
4
Relay 4 energizes, maintained momentary

461-8000-AC
4
RELAY, FREQUENCY, & DELAY SETUP
The unit is shipped from the factory
with SEL1 switches in the open
positions. All four relays will operate as
maintained momentary, the unit is
receiving commands on frequency 1,
and the safety delay timer is set to 5
seconds. To change default settings,
follow the instructions below:
1. *IMPORTANT*
Disconnect power from unit.
2. Remove top cover.
3. Select desired relay operation
and/or frequency using the
table.
4. Reattach cover.
5. Reconnect power to unit.
6. Programming is complete.
RELAY CONFIGURATION
SEL1
SW#
OPEN (default)
CLOSED
SW1
Relay #1 momentary
Relay #1 toggle/latch
SW2
Relay #2 momentary
Relay #2 toggle/latch
SW3
Relay #3 momentary
Relay #3 toggle/latch
SW4
Relay #4 momentary
Relay #4 toggle/latch
Maintained Momentary –Relay mimics button or input –
when depressed or closed, relay will be energized; when
released, relay de-energizes.
Toggle Latch –Relay changes and holds its state each time
the corresponding button or input is depressed or closed.
FREQUENCY SETUP
NETWORK
FREQUENCY
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
SAFETY DELAY TIMER
TIME
SW8
SW9
5 Seconds (default)
OPEN
OPEN
30 Seconds
CLOSED
OPEN
60 Seconds
OPEN
CLOSED
90 Seconds
CLOSED
CLOSED
The safety delay timer allows the unit to keep the relay active
during periods of high interference or bad reception. This is
the amount of time that a signal must be lost before turning
off the relay. This also acts as a safety feature to turn off the
relay if the RELAY OFF code is missed due to bad signal.

461-8000-AC
5
CONTROLS & INDICATORS
POWER/TX
LED1
Dual color LED illuminates red while unit is booting up, changes to green
when boot-up is successful and unit is ready to operate.
If this LED fails to turn green, power unit off for 15-20 seconds, then
reapply power.
LED2
Illuminates green while relay 1 is energized
LED3
Illuminates green while relay 2 is energized
LED4
Illuminates green while relay 3 is energized
LED5
Illuminates green while relay 4 is energized
REL1 –REL4
Four SPDT output control relays
RF1
RF Module that transmits/receives data
APPROVALS
United States (FCC)
MCQ-XBPSX
Canada (IC)
1846A-XBPSX
Australia
RCM
Brazil
ANATEL: 05774-16-01209

461-8000-AC
6
SPECIFICATIONS
Power Supply
100-250 VAC, 5 W, 50/60 Hz
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC per channel
Fuse Protected
1 amp
Frequency
902-928 MHz Spread Spectrum
Range
Up to 5000 feet * (Up to 10 miles with external
antenna - see accessories)
RF Networks
Eight Independent Network Frequencies
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate, IP66 (NEMA 4)
*Note: Max range statements are estimates based on a clear line of sight with few
interferences. Actual range will vary based on transmitting power, orientation of
transmitter and receiver, height of transmitting and receiving antennas, weather
conditions, electronic interference, terrain, and physical obstacles, including but not
limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills,
mountains).
ACCESSORIES
STANDARD ANTENNA (INCLUDED)
900MHz TNC Portable “Rubber Duck” Antenna
49-1103
MOBILE/BASE ANTENNAS (OPTIONAL)
Used to help achieve max range in non-line-of-sight and line-of-sight applications.
Contact BWI Eagle for recommendations.
900MHz Thru-Hole/Bracket Mount Mobile Antenna
49-2101
900MHz Magnet Mount Mobile Antenna
49-2102
900MHz Omni Directional Base Antenna
49-3101
900MHz Yagi Directional Base Antenna
49-3102
HIGH QUALITY COAX CABLE
Used to connect external antennas to control unit.
Flex Coax Cable w/Connectors
(Available in 5’, 15’, 25’, 30’, 40’, 60’, 80’, and 100’ lengths)
49-4000-XX
(XX = length in feet)
BULKHEAD EXTENSION
Used to provide an external antenna connection when mounting control unit
inside another enclosure.
TNC Male to TNC Bulkhead Cable Assembly
(Available in 2’, 4’, and 7’ lengths)
49-5004-X-ISO
(X = length in feet)

461-8000-AC
7
DIMENSIONS