BWI Eagle AIR-EAGLE XLT 44P-8-ESTOP Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT
900 MHz RF Receiver
MODEL 44P-8-ESTOP
DESCRIPTION
The AIR-EAGLE XLTis an RF system designed for long range wireless
remote control of electrical apparatus in a variety of industrial applications.
This receiver has been specificallydesigned forE-Stop applications. It
links with anE-stop transmitter for failsafe operation. Dipswitches allow
the user to select link-loss shutdown times, relay operation and whether
power must be recycled to reset thesystem. The relays are capable of
switching up to 5 amps @120VAC or 30VDC and can be directly
interfaced with the customer's equipment or P.L.C. Seven user selectable
frequencies allowmultiple systems to be usedin the same area. This
receiver is capable of receiving remote signals transmitted from upto
2500 feet away.
INSTALLATION
DISCONNECT AC Power from all equipment before installation.
1. Mount the AIR-EAGLE XLT RECEIVER in a convenient location.
2. Select options & frequency (See OPTIONS & FREQUENCY SET-
UP)
3. Install relay wiring to terminal strip.
4. Install antenna onto connector located on the right side on the
enclosure.
5. Connect AC power to the proper terminals in your control circuit.
TERMINAL STRIP WIRING
1
N/O Relay #1
7
N/O Relay #3
13
120 VAC - (Neutral)
2
C Relay #1
8
C Relay #3
14
120 VAC - (Hot)
3
N/C Relay #1
9
N/C Relay #3
4
N/O Relay #2
10
N/O Relay #4
5
C Relay #2
11
C Relay #4
6
N/C Relay #2
12
N/C Relay #4
GENERAL OPERATION
Prior to operation the user selects various options that control the link-loss
shutdown, relay activation and system reset. (See OPTIONS &
FREQUENCY SET-UP).
When power is applied to the receiver, all relays will be in their de-
energized state. When power is applied to the E-stop transmitter, it
immediately begins sending a beacon signal thatcauses the selected
relays in the receiver to energize, indicating the communications link.
Upon an E-stop command, the selected relays immediately de-energize.
Upon specified link-loss time, the selected relays de-energize. The system
will then need to be manually reset or will automatically come back online
as designated by the system operation optionselected.
Dimensions (with mounting plate) 6.3” L x 4.8” W x 2.3” H
CONTROLS AND INDICATORS
.
LED1
Illuminated when power is applied to receiver
LED2
Illuminated when relay #1 is energized
LED3
Illuminated when relay #2 is energized
LED4
Illuminated when relay #3 is energized
LED5
Illuminated when relay #4 is energized
RF1
RF module that receives data from the remote
transmitter
REL1 thru REL4
Four SPDT output control relays

AIR-EAGLE®XLT
900 MHz RF Receiver
MODEL 44P-8-ESTOP
OPTIONS & FREQUENCY SET-UP
The unit is shipped from the factory with all SEL1 switches in the open
positions. By default, the link-loss shutdown timeis setto .5 seconds;
power must be recycled to reset thesystemfollowing an E-stop event; all
relays respond to either E-stop command; andthe unit is operating on
Frequency #1. If you wish to select different options and/or change the
frequency, follow the instructions on the table below.
1) Remove power from unit
2) Remove top cover.
3) Select desired options and/or frequency using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
LINK-LOSS SHUTDOWN
SEL1 (SW1-2)
Link-Loss
Shutdown Time
in Seconds
SW1
SW2
0.5 (default)
OPEN
OPEN
0.25
CLOSED
OPEN
1
OPEN
CLOSED
1.5
CLOSED
CLOSED
SYSTEM RESET OPTIONS
SEL1 (SW3)
System Reset Requirement
SW3
Power must be recycled to receiver following any
E-stop event (default)
OPEN
Relays revert to energized state upon release of E-
stop button and resumption ofcommunication link
CLOSED
RELAY RESPONSE OPTIONS
SEL1 (SW4)
Relay Response to E-Stop Event
SW4
All four relays de-energize upon E-stop command
OR link-loss (default)
OPEN
Relays 1 & 2 de-energize upon E-stop command;
Relays 3 & 4 de-energize upon link loss
CLOSED
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
DOCUMENT DATE: 03/01/2019 / PRODUCT REV. 5
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com
SPECIFICATIONS
AC Input
120 VAC, 16 W, 50/60 Hz
Relay Contacts
SPDT 5 amp @ 120VACor 30VDC per
channel
Fuse Protected
1 amp
Receiver Range
Approximately 2500 feet (Up to 4 miles
with external antenna - see
accessories)
Receiver Frequency
900 MHz Spread Spectrum
Receiver Channels
Seven independent network frequencies
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate, IP66 (NEMA 4)
Weight
Approx 2 lbs.
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
ACCESSORIES
Standard Antenna (Included):
900MHz Portable Antenna (For distances up
to 2500 feet*)
49-1103
Optional Antennas and Accessories –
Used to increase range in both non line of sight and line of sight
applications. - Contact BWI Eagle for recommendations
900MHz Omni Directional Antenna (For
distances up to 2 miles*)
49-3101
900MHz 13dB Yagi Antenna
Long Range Operation (For distances up to
4 miles*)
49-3102
Flex Coax Cable w/Connectors
49-4000-XX
(XX = # of Feet)
Inline Lightening Arrestor
49-5002
2 Ft. Bulkhead Assembly (Used when
mounting receiver inside another enclosure)
49-5004
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants theAir-Eagle Remote ControlSystem, if properly
used and installed, will be free from defects inmaterial and workmanship
for a period of 1 year after date of purchase. Said warranty to include the
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improperinstallation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eaglemakes no express warranties beyond
thosestated here. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss duringshipping and is
responsible for the shipping costs incurred.