Callaway 250+ User manual

250 + LASER RANGEFINDER

Product Callaway 250+ Laser Rangender
Model 250+
Dimensions 3.74” x 2.80” x 1.57”
Weight 5.4 oz. (155g) (Without Battery)
Battery CR2 3-Volt Lithium Battery
Display LCD display
Magnication 6X
Max Range 5-950 yd
Range To Flag 5-300 yd
Accuracy +/- 1 yd
Slope Measurement Range -89° - 90°
Unit of Measure Yards/Meters
Water/Fog Proof Weather Resistant (IPX3)
SPECIFICATIONS
INTRODUCTION
Thank You for choosing the Callaway 250+ Laser Rangefinder
featuring P.A.T. (Pin Acquisition Technology) with Pulse Technology
& Slope Mode. Designed to deliver precise distance measurements,
P.A.T. locks onto the agstick up to 300 yards away, ensuring accuracy
even when trees and other objects are in the background.
2INTRODUCTION

BATTERY INSTALLATION
1. Lift hatch tab.
2. Turn counterclockwise to open.
3. Remove protective plastic battery cover.
4. Replace battery cap & tighten by turning clockwise.
NOTE: If the Low Battery Icon is present on LCD display, there are
approximately 200 ranges left until the battery is completely drained.
The Low Battery Icon will ash if the battery life is very low. In this
case, the battery needs to be replaced before next use.
BATTERY INSTALLATION 3
INCLUDES
A. CR2 - 3-Volt Lithium Battery
B. Carry Case
C. Cleaning Cloth

RANGEFINDER DIAGRAM
A. Eye Piece
B. Diopter Adjustment
C. Power Button
D. Battery Door
LCD DISPLAY
A. Zero-In Aiming Square
B. Laser Indicator Box
C. P.A.T. Mode Indicator
D. Pulse Indicator
E. Distance
F. Unit of Measure
G. Low Battery
H. Slope Adjusted Distance
4HOW TO USE
164Y

HOW TO USE
1. While looking through the Eye
Piece, PRESS and RELEASE the
Power Button. The rangender is
now powered on.
2. To focus/increase clarity, use the
Diopter Adjustment by turning
the Eye Piece.
3. Continue looking through the Eye
Piece, aim the Zero-In Aiming
Square at your intended target and
PRESS the Power Button. The laser
will re and the Laser Indicator
Box will appear around the Zero-In
Aiming Square. The measurement
will be displayed at the top of the
LCD display.
HOW TO USE 5
164Y

MEASUREMENT MODES
1. Standard - Standard Mode is recommended when measuring
distances to larger objects. (Fig. A)
2.
6HOW TO USE
P.A.T. with Pulse Technology - P.A.T. Mode is best used when
measuring the distance to a Flagstick or smaller objects. Device
will provide a short vibration to conrm that the laser has locked
on to the pin. To toggle between Standard and P.A.T Mode, quickly
PRESS the Power Button Twice while device is powered on.
When P.A.T. Mode is activated, the agstick icon will appear on
the left side and the Pulse icon will appear on the right side of the
LCD display. (Fig. B)
3. Scanning - To measure distances to multiple targets in succession,
PRESS & RELEASE the Power Button to power on. Then HOLD
Power Button, the Laser Indicator Box will ash and the laser
will continuously re. Measurements will change as you scan the
landscape and change targets.
NOTE: While scanning in P.A.T. Mode, the measurement will only change
when a shorter distance is measured. This is useful when measuring the
distance to a agstick when there are trees or other objects in the background.
NOTE: To disable Pulse Technology but keep P.A.T. Mode activated,
start with the device powered o󰀨. Next, HOLD the Power Button for
5 seconds. The Pulse icon on the right side of the screen will ash &
turn o󰀨. To enable Pulse Technology again, repeat this process.

HOW TO USE 7
4. Slope Mode - Device will measure the angle of incline/decline (Fig. B)
then calculate and display the slope adjusted distance in the bottom
right of the LCD display. (Fig. C)
• To turn Slope Measurement On/O󰀨:
NOTE: The slope measurement & adjusted yardage will appear in
the bottom right corner of the LCD display when the function is enabled
1. With the unit o󰀨, HOLD the Power Button for three seconds
until the slope function appears in the bottom right corner of the
LCD display. Once the slope function appears, RELEASE the
Power Button.
2. Repeat this process if you need to turn The Slope Measurement
o󰀨. The Slope function will not appear unless enabled.
5. Unit of Measure - To change the unit of measure from Yards to
Meters, start with the device powered o󰀨. Then HOLD the Power
Button for 7 sec. The unit of measure is indicated by a “Y” or “M”
shown directly to the right of the distance displayed.

OPERATIONAL NOTES
1. The maximum measurement range is 5-950 yards to objects and
5-300 yards to a agstick with +/- 1 yard accuracy.
NOTE: Maximum range can depend on several factors, including
target characteristics and environmental conditions. For instance,
longer maximum distances may be obtained to targets that are
large in size, brightly colored, or have a reective nish. Ranging
capability can also be a󰀨ected by the angle to the target and
lighting conditions.
2. Auto Shuto󰀨 - To conserve battery life, the device will
automatically power o󰀨 when idle for more than 10 seconds.
3. Weather Conditions - Heavy rain and thick fog can potentially
limit the maximum range of the device.
4. Weather Resistant - Protected against light rain.
STORING THE LASER
• Do not leave the eyepiece in
direct sunlight. The condenser
e󰀨ect of the lens may damage
the internal display surface.
MAINTENANCE
1. To clean, use only a soft, clean cloth to prevent scratches.
2. Do not submerge in liquid or apply any cleaning products.
3. Do not store in extremely hot/cold temperatures (<50°F - >110° F).
4. Store in carrying case when not in use.
8MAINTENANCE

TROUBLESHOOTING 9
TROUBLESHOOTING
Rangender is consistently providing inaccurate measurements.
• Make sure the device is set to the desired unit of measure
(Yards or Meters).
• Weak battery signal can a󰀨ect the accuracy of the device. If the
Low Battery Indicator is present on the LCD display, replace
the battery.
• Make sure there isn’t anything obstructing your view such as
leaves, branches, your nger, etc.
When looking through the Eye Piece, the view is blurry.
• Use the Diopter Adjustment by turning the Eye Piece to focus/
increase clarity.
• Make sure there isn’t anything obstructing your view such as
leaves, branches, your nger, etc.
• Use a soft, clean cloth to clean lens.
When should the battery be replaced?
• If the Low Battery Indicator is present on the LCD display.
• If the rangender is consistently providing inaccurate
measurements.
• If the LCD display is not present when PRESSING the
Power Button.
What type of battery does the rangender use?
• CR2 3-Volt Lithium Battery.

10 TROUBLESHOOTING
TROUBLESHOOTING (CONTINUED)
When should P.A.T. Mode be used?
• When measuring the distance to smaller targets such as
a agstick.
• When scanning the landscape to measure distances to a smaller
target such as a agstick and there are trees or other objects in
the background.
WARRANTY POLICY
This product is warranted to be free from defects for up to (1) year
from the original purchase date. IZZO Golf cannot refund your
purchase unless purchased directly from IZZO Golf. IZZO Golf will
replace or repair any unit that is determined defective under normal
use within the warranty period. Please call Customer Service at
888-606-4634 to request a Return Authorization. All defective
products must be returned to:
IZZO Golf
Attn: Returns Dept.
1635 Commons Parkway
Macedon, NY 14502
Please include a note with your Name, Address, Phone # and the
Return Authorization #.Your replacement will be shipped once we
diagnose the returned unit.
If you have any other questions or concerns,
please call 1-888-606-4634 or go to www.callawaydmd.com.

WARNING
• NEVER look directly into the sun or intense light when using
the laser rangender.
• DO NOT aim/point laser rangender at another person.
• DO NOT aim/point laser rangender at anyone’s eyes or face.
• DO NOT attempt to disassemble the laser rangender.
• DO NOT submerge in any liquid.
• DO NOT store the laser rangender in extreme cold/hot
temperatures (<50°F - >110°F).
© 2019 CALLAWAY GOLF COMPANY. Callaway Golf and the
Chevron device are trademarks of Callaway Golf Company.
IZZO Golf is an o󰀩cial licensee of Callaway Golf Company.
WARNING 11