Callaway TOUR-S User manual

TOUR-S LASER RANGEFINDER

Product Callaway TOUR-S Laser Rangender
Model TOUR-S
Dimensions 4.5” x 3” x 1.65”
Weight 195 grams, (6.8 oz.) (Without Battery)
Battery CR2 3-Volt Lithium Battery
Display OLED display
Magnication 7X
Max Range 5-1200 yd
Range To Flag 5-400 yd
Accuracy +/- .5 yd
Slope Measurement Range -89° - 90°
Unit of Measure Yards/Meters
Water/Fog Proof Weather Resistant (IPX3)
SPECIFICATIONS
INTRODUCTION
Thank You for choosing the Callaway TOUR-S Laser Rangender
which utilizes our most advanced laser technology in one device.
With P.A.T. (Pin Acquisition Technology), Slope Technology, and
Prism Mode, the Tour-S is capable of providing exact distance
measurements to virtually any target!
2INTRODUCTION

BATTERY INSTALLATION
1. Lift hatch tab.
2. Turn counterclockwise to open.
3. Remove protective plastic battery cover.
4. Replace battery cap & tighten by turning clockwise.
NOTE: If the Low Battery Icon is present on display, there are
approximately 200 ranges left until the battery is completely drained.
The Low Battery Icon will ash if the battery life is very low. In this
case, the battery needs to be replaced before next use.
BATTERY INSTALLATION 3
INCLUDES
A. CR2 - 3-Volt Lithium Battery
B. Carry Case
C. Cleaning Cloth

INTERNAL DISPLAY
A. Zero-In Aiming Square
B. Laser Indicator Box
C. P.A.T. Mode Indicator
D. Prism Mode Indicator
E. Distance
F. Unit of Measure
G. Slope Adjusted Distance
H. Low Battery
4 HOW TO USE
164Y
RANGEFINDER DIAGRAM
A. Eye Piece
B. Diopter
Adjustment
C. Power Button
D. Mode Button
E. Slope Switch
F. Battery Door

HOW TO USE 5
HOW TO USE
1. While looking through the Eye
Piece, PRESS and RELEASE the
Power Button. The rangender is
now powered on.
2. To focus/increase clarity, use the
Diopter Adjustment by turning
the Eye Piece.
3. Continue looking through the Eye
Piece, aim the Zero-In Aiming Square
at your intended target & PRESS the
Power Button. The laser will re and
the Laser Indicator Box will appear
around the Zero-In Aiming Square.
The measurement will be displayed at
the top of the display.
164Y

MEASUREMENT MODES
•To change the measurement mode on the Tour-S, rst PRESS the
Power Button once to power the laser on. Next, PRESS the Mode
Button to cycle between the di󰀨erent modes. There are 3 di󰀨erent
laser ring modes on the Tour-S:
1. Standard Mode: No Icon will appear on the left side of the display
(Fig. A). Standard Mode is recommended when measuring distances
to larger objects. Single PRESS the Power Button once to single
re the laser or Press and Hold to continuously re the laser. By
pressing and holding the power button, the laser with continuously
re & change yardage readings until the power button is released.
To measure distances to multiple targets in succession, HOLD
the Power Button. The Laser Indicator Box will ash and the laser
will continuously re. Measurements will change as you scan the
landscape and change targets.
2. P.A.T. (Pin Acquisition Technology): A Flag Icon will appear on
the left side of the screen (Fig. B). P.A.T. Mode is best used when
measuring the distance to a agstick or smaller objects especially
with trees or other objects in the background. Single Press the
Power Button once to single fire the laser or Press and Hold
to continuously re the laser. The Laser will lock onto the closest
recorded yardage during the ring period.
6HOW TO USE

HOW TO USE 7
NOTE: While scanning in P.A.T. Mode, the measurement will only
change when a shorter distance is measured. This is useful when
measuring the distance to a agstick when there are trees or other
objects in the background.
3. Prism Mode: A Flag Icon with a Square Border will appear
on the left side when enabled (Fig. C). This mode will only provide
yardage readings when the laser hits a prism reector located on
the ag stick. Single PRESS the Power Button once to re the
laser. The laser will re until it hits a reective target. NOTE: The
unit will not provide yardage readings if there are no reectors on
the ag stick while in this mode.
4. Unit of Measure - To change the unit of measure from Yards
to Meters, PRESS the Power Button once to power the unit
on. Next, HOLD the Mode Button until “SEL” appears on the
display. Next, PRESS the Power Button ONCE to display “Y”
for yards or “M” for meters. PRESS the Mode Button to cycle
between yards or meters. Once the correct measurement is
selected, PRESS the Power Button twice to exit.

8HOW TO USE
SLOPE FUNCTION
Device will measure the angle of incline/decline (Fig. B) then
calculate & display the slope adjusted distance in the bottom right
of the display (Fig. C).
The Slope switch on the Side of the Tour-S has two positions:
1. RED is showing: Slope function is o󰀨. The Laser is tournament
legal when the slope is turned o󰀨.
2. GREEN is showing: Slope function is enabled. Slope adjusted
yardage will be displayed after every time the laser is red. The
Laser is not tournament legal when the slope is enabled.
SLOPE OFF SLOPE ON

HOW TO USE 9
DISABLING DECIMAL MEASUREMENT
Your Tour-S laser is preset to display yardage readings to the nearest
tenth (1/10) of a yard. The user can remove the extra digit if desired.
• Disabling Decimal Measurement:
• Power the unit on by PRESSING the Power Button once
• Next, quickly PRESS the Mode Button twice
• Your Tour-S will now provide yardage readings to the nearest
tenth of a yard.
• To enable decimal measurement again, quickly PRESS the
Mode Button twice.
OLED DISPLAY
Your Tour-S laser has an adjustable brightness OLED Display. The
Tour-S comes preset on the highest brightness level for daylight
playing conditions. In low light or overcast weather conditions, the
OLED red display may show a red backlight border. This backlight
border can be removed by adjusting the brightness to the lower level.
ADJUSTING BRIGHTNESS LEVEL
First, PRESS the Power Button once to power the unit on. Next,
HOLD the Mode Button until “SEL” appears on the display. Next,
PRESS the Power Button TWICE to display “BL2”. Now PRESS
the Mode Button to cycle between “BL2” or “BL1”. “BL2” is the
highest brightness level and “BL1” is the lowest brightness setting.
Once the correct brightness is selected, PRESS the Power Button
once to exit.

OPERATIONAL NOTES
1. The maximum measurement range is 5-1200 yards to objects and
5-400 yards to a agstick with +/- .5 yard accuracy.
NOTE: Maximum range can depend on several factors, including
target characteristics and environmental conditions. For instance,
longer maximum distances may be obtained to targets that are
large in size, brightly colored, or have a reective nish. Ranging
capability can also be a󰀨ected by the angle to the target and
lighting conditions.
2. Auto Shuto󰀨 - To conserve battery life, the device will
automatically power o󰀨 when idle for more than 10 seconds.
3. Weather Conditions - Heavy rain and thick fog can potentially
limit the maximum range of the device.
4. Weather Resistant - Protected against light rain.
STORING THE LASER
• Do not leave the eyepiece in
direct sunlight. The condenser
e󰀨ect of the lens may damage
the internal display surface.
MAINTENANCE
1. To clean, use only a soft, clean cloth to prevent scratches.
2. Do not submerge in liquid or apply any cleaning products.
3. Do not store in extremely hot/cold temperatures (<50°F - >110° F).
4. Store in carrying case when not in use.
10 MAINTENANCE

TROUBLESHOOTING 11
TROUBLESHOOTING
Rangender is consistently providing inaccurate measurements.
• Make sure the device is set to the desired unit of measure
(Yards or Meters).
• Weak battery signal can a󰀨ect the accuracy of the device. If
the Low Battery Indicator is present on the display, replace
the battery.
• Make sure there isn’t anything obstructing your view such as
leaves, branches, your nger, etc.
When looking through the Eye Piece, the view is blurry.
• Use the Diopter Adjustment by turning the Eye Piece to focus/
increase clarity.
• Make sure there isn’t anything obstructing your view such as
leaves, branches, your nger, etc.
• Use a soft, clean cloth to clean lens.
When should the battery be replaced?
• If the Low Battery Indicator is present on the display.
• If the rangender is consistently providing inaccurate
measurements.
• If the display is not present when PRESSING the
Power Button.
What type of battery does the rangender use?
• CR2 3-Volt Lithium Battery.

12 TROUBLESHOOTING
TROUBLESHOOTING (CONTINUED)
When should P.A.T. Mode be used?
• When measuring the distance to smaller targets such as
a agstick.
• When scanning the landscape to measure distances to a smaller
target such as a agstick and there are trees or other objects in
the background.
WARRANTY POLICY
This product is warranted to be free from defects for up to (1) year
from the original purchase date. IZZO Golf cannot refund your
purchase unless purchased directly from IZZO Golf. IZZO Golf will
replace or repair any unit that is determined defective under normal
use within the warranty period. Please call Customer Service at
888-606-4634 to request a Return Authorization. All defective
products must be returned to:
IZZO Golf
Attn: Returns Dept.
1635 Commons Parkway
Macedon, NY 14502
Please include a note with your Name, Address, Phone # and the
Return Authorization #.Your replacement will be shipped once we
diagnose the returned unit.
If you have any other questions or concerns,
please call 1-888-606-4634 or go to www.callawaydmd.com.

WARNING
• NEVER look directly into the sun or intense light when using
the laser rangender.
• DO NOT aim/point laser rangender at another person.
• DO NOT aim/point laser rangender at anyone’s eyes or face.
• DO NOT attempt to disassemble the laser rangender.
• DO NOT submerge in any liquid.
• DO NOT store the laser rangender in extreme cold/hot
temperatures (<50°F - >110°F).
© 2018 CALLAWAY GOLF COMPANY. Callaway Golf and the
Chevron device are trademarks of Callaway Golf Company.
IZZO Golf is an o󰀩cial licensee of Callaway Golf Company.
WARNING 13

© 2018 CALLAWAY GOLF COMPANY. Callaway Golf and the
Chevron device are trademarks of Callaway Golf Company.
IZZO Golf is an o󰀩cial licensee of Callaway Golf Company.