Calortrans CT3838II User manual

MANUAL
Calortrans
CT3838II

IMPORTANT SAFETY INSTRUCTIONS
For safe use of the Calortrans CT3838II Heatpress the following precautions should be
taken.
Before use:
• Read the entire manual before using the press
• Use the press only for textile transfers or products suitable for sublimations
• The power cord must be connected directly to the power outlet without an
extention cord.
• Before connecting the machine, check that the voltage of the power cable is
230 volts and the power is at least 10 amps.
• Do not use the machine if the power cord is damaged or defective. In the event
of damage or malfunction, do not open the press, but contact your dealer
immediately. If the press has been opened, the guarantee will expire.
• Do not use the transfer press in the presence of children or unauthorized
persons, due to the risk of catching burns. If the transfer press is nevertheless
used in the vicinity of children, a minimum distance of 1.5 meters must be
maintained.
• Avoid contact of the transfer press with moisture, dirt, dust, mechanical
vibrati ons or shocks.
While operating:
• Alwaysusetheon/o󰀨buttontoturno󰀨thetransferpress,neverunplugthe
power cord to do this.
• Do not touch the heat element during use to avoid the danger of catching
burns.
• Avoid contact of the power cable with the heat element.
• While in operation, never leave the press unattended
Additional instructions:
• When lifting and moving the transfer press, avoid touching the heat
element and only the frame must be gripped. Before shipment, the transfer
press must be completely cooled down and be packed in the original
packaging.
• Keep these safety instructions in a safe place.
2
Safety

3
TABLE OF CONTENT
Manual 1
Safety 2
Table of content 3
Machine in detail 4
Technicality Specications: 5
Display in detail 5
Preface 6
Usermanual 7
CE certication 10

4
Machine in detail
Display
Handle
On/O󰀨switch
Power
Pressure regulator

Technical specs: 2000W / 240V/50Hz
Size with packaging: 450x550x460cm
Weight: 23Kg
Current Temperature
1. Pieces count
2. Target temperature
Countdown timer
Increase or decrease
temperature and time
Menu
5
Display in detail

6
This manual was made to make the usage of the Calortrans CT3838II trans-
fer press as easy and safe as possible. It is therefore recommended that you
read this manual carefully and follow the instructions step by step.
• Work carefully and avoid direct contact with the heat element to
reduce the risk of burns.
• Only use the transfer press when it is placed on a stable surface.
• Upon delivery, check the press for transport damage. Then let the
transfer press acclimatize for 7 hours at room temperature to prevent
moisture problems or any chance of a short circuit.
• Adjust the position of the transfer press to the preferred height of the
end user.
• Use the transfer press preferably with one, if necessary two
hands.
• The optimal recommended ambient temperature when using the
transfer press is between 15-50 ° C, with a relative humidity of up to
70%.
• Never place liquid materials or solid objects in the transfer press. If
 thisdoeshappen,turnthemachineo󰀨immediatelyandremovethe
power cord from the wall socket. Then immediately contact your
dealer.
• The manufacturer assumes no liability if property damage or personal
injury is caused by improper use of the transfer press
Preface

Note:
If the power cord is damaged, it must
be replaced by the manufacturer or a
technician. This is to avoid any risk of
electric shock. Use a 250V power cable
- 10 AMP for replacement..
Warning:
Ignoring this information can cause:
• Damage to the machine
• Short circuit
7
Step 1. Connect the power cord
Check if the voltage is 230V before the
machine is connected.
The socket must be protected with at
least 10 amps.
Do not use an extension cable, this
can cause overheating of the power
cable and / or loss of voltage.
Step 2. Turning the machine on
• Open the transfer press.
• Locatetheof/o󰀨button.
• Switch the transfer press on.
Usermanual

Note:
Adjust the pressure of the transfer press to the material you are going to use by
turning the pressure regulator. (hold the handle slghtly down while turning the knob)
As soon as the handle is closed, the product is heated by the heat element. The
time is automatically counted down and as soon as the transfer press is ready, the
machine gives a signal.
8
Usermanual
Step 3. Setting the temperature and time
1. Press and hold the menu button (for a few seconds) until it
beeps.Thetemperaturesettingwillnowash.
Use the arrow keys to increase or decrease the temperature.
2. Press the menu button again to set the time.
Use the arrow keys again to decrease or increase the time.
3. Press the menu button again. Press the arrow down button to
reset the number of pieces.
4. Press the menu button one last time and the press is ready
to use.

Warning:
It is necessary that the pressure is correctly adjusted before the product is pressed.
9
Step 4. Usage
Once the transfer press has reached the working temperature.
• Set the desired pressure corresponding with the material that you
wish to press.
• Place the product under the transfer press.
• Press the handle all the way down until in clicks in place
• Raise the handle when the signal is given that the time has
elapsed and the transfer process is complete.
Usermanual
Turn clockwise to increase the
pressure. Turn counterclockwise
to reduce pressure. Consult your
dealer for the correct pressure
corresponding to the material you
wish to press.

10
CE Certicate