CAMDEN CX-DE1200 User manual

Page 1 of 9
CX-DE1200
Delayed Egress Electro Magnetic Lock
Special Locking Arrangement
INSTALLATION INSTRUCTIONS
Electrified Locks, Relays and Timers
1- CX-DE1200 Electro Magnetic Lock Housing
assemble with main controller PCB & Magnetic Plate
1- Mounting Template
4- Adhesive door signage
1- Installation Instructions & Wiring Diagrams
1- Armature Plate Assembled Housing
& Proxy Trigger
1- Electro Magnetic Lock Screw Packaging
THIS PACKAGE INCLUDES:
1. DESCRIPTION
Intended for use in an Indoor location - Out Swing.
When an unauthorized exit is trigger, the delays exit through
the door for a period of 15 or 30 seconds. An LED bar segment
display countdown by seconds and voice messages to inform
the person planning to exit with the remaining times to unlock.
In the meantime, the person exiting must wait to allow time for
security personnel or sta to respond. The door will eventually
unlock after the 15 or 30 seconds delay time has passed,
permitting the exit. During an emergency, a signal from the
re/life safety system will release the lock promptly.
2. SPECIFICATIONS
Voltage
12/24V DC +/- 10% (Auto Sensing)
Power Suplly must be UL 294 or
UL 603 Listed with a Class 2, power
limited output
Current Draw 600mA / 350mA
Lock Output 12/24 VDC, 1A
Lock Status Relay
Rating Max. * 30 VDC, 2A, 1 pF
Alarm Output
Rating Max. * 30 VDC, 2A, 1 pF
DPS Rating Max. * 30 VDC, 0.1A, 1 pF
Bond Sensor Rating Max. * 30 VDC, 2A, 1 pF
ATS Rating Max. * 30 VAC / 42.4 VDC, 5A, 1 pF
Operating Temperature 0~55°C (32~131°F)
Operating Humidity 0~95% (non-condensing)
Dimensions
(Lock)
11” H x 3” W x 3” D
(280mm x 76mm x 74.5mm)
Dimensions
(Armature Plate)
11” H x 2-5/8” W x 1” D
(280mm x 68mm x 23.5mm)
3. DIMENSIONS
PUSH UNTIL ALARM SOUNDS.
DOOR CAN BE OPENED
IN 15 SECONDS.
PUSH UNTIL ALARM SOUNDS.
DOOR CAN BE OPENED
IN 30 SECONDS.
KEEP PUSHING.
THIS DOOR WILL OPEN
IN 15 SECONDS.
ALARM WILL SOUND.
KEEP PUSHING.
THIS DOOR WILL OPEN
IN 30 SECONDS.
ALARM WILL SOUND.
Building & Fire Life Safety Code Compliant:
IBC International Building Code
NFPA 101 Life Safety Code
NFPA 1, UFC Uniform Fire Code
CBC California Building Code
BOCA National Building Code
Chicago Building Code
THIS PRODUCT MUST BE CONNECTED INTO A FIRE ALARM SYSTEM PER NFPA
CODE OR OTHER REGULATIONS SO THAT, IN THE EVENT OF FIRE, THE TIME
DELAY WILL BE BYPASSED. CONTACT YOUR LOCAL CODE AUTHORITY TO VERIFY
COMPLIANCE WITH FIRE AND BUILDING CODES. THE DELAYED EGRESS DEVICE
SHOULD BE ROUTINELY CHECKED FOR PROPER OPERATION AND COMPLIANCE
WITH FIRE AND BUILDING CODES.
Note: * Separately-energized
UL 294 Access Control
Performance Levels: Levels:
Access Control Line Security Level I
Destructive Attack Level I
Endurance Level IV
Standby Power Level I

Page 2 of 9
CX-DE1200 Delayed Egress Electro Magnetic Lock
INSTALLATION INSTRUCTIONS
4. FEATURES
• Holding Force up to 1200 Lbs. (Not validated by UL)
• Field selectable exit delay time 15 or 30 seconds
• Nuisance Delay period either 1, 2 or 3 seconds
• 75dB Buzzing Tone with LED segment bar display time
seconds & eld selectable voice alerts
• Choice of sensor to be activated:
- Door Motion
- Door Exit Device with momentary normally open contact
- Push Bar with momentary normally open contact
• Auto Start Up:
- Occurs when power supply is restored and/or the re panel is
restored (When allowed by Building & Fire Life Safety Code)
• Manual Start Up:
- This is a California & UBC Building Code Compliant Feature.
Only after power supply restoration and re panel reset
may the lock be Reset manual at the opening. This lock can
be reset with the built-in reset key switch or an external key
switch or a reset switch connected to the door
• Vandal resistant Proximity Trigger Sensor
• Auto Sensing Voltage Power Input 12/24 VDC
• Reverse power protection:
If someone hooks power up backwards, the board simply
does not turn on, protecting it from damage
• Optional Connection for Auxiliary Lock, CX-DE1201 (Double
Leaf Door)
• Hall Eect Sensor Monitoring Output
• Tamper Switch Output
• Tailgating Prevention - door will re-lock as soon as it closes
• Anti-Pass Back / Auto re-lock:
If door doesn't open after the count down, the door will
automatically re-lock.
5. INSTALLATION CONCEPT AND ACCESSORIES
Seven conguration versions are available to be compliant to regional jurisdictions.
Models
Delay Release Time
(Seconds)
Nuisance Delay
(Seconds) Reset After Alarm Lock Status on Power-Up
Fixed Selectable Fixed Selectable Selectable Fixed Fixed Selectable
CX-DE1200 15 or 30 1 or 2 Manual Locked / Unlocked
CX-DE1200-N2 15 0 or 1 Manual Locked / Unlocked
CX-DE1200-N3 30 0 or 1 Manual Locked / Unlocked
CX-DE1200-N4 15 0 or 1 Manual Unlocked
CX-DE1200-B1 15 0 or 3 Auto / Manual Locked / Unlocked
CX-DE1200-B2 30 0 or 3 Auto / Manual Locked / Unlocked
CX-DE1200-B3 15 0Auto / Manual Locked / Unlocked
N# = NFPA Compliance B# = BOCA Compliance
BOCA Compliance
Manual Reset: Is achieved by authorized personnel closing the door after an alarm and actuating the integral reset key switch
or by momentarily closing a contact connected to the remote RESET terminal.
Automatic Reset: Reset will automatically be initiated once the door has been opened, then closed and remains closed for
30 consecutive seconds.
Release Time Warning Type WARNING!
Contact authority having jurisdiction for approval prior to
selecting release time, nuisance time and start-up settings.
!
Languages
Voice Type
Nuisance Time
R-Exit Time
Trigger type
Start-Up State
Door POS Alarm
Anti Pass Back
Dip Switch Settings

Page 3 of 9
CX-DE1200 Delayed Egress Electro Magnetic Lock
INSTALLATION INSTRUCTIONS
Pwr
NO C NC
Fire P
CNC
Lock Grn Rly Red Rly Ex-Trig Reset R-Exit Bypass
Ex-Spkr DPS Bond-S ATS
ON DIP
12345678
NO C NC NO CNO CNO CNO CNO C NC NO C NC NO C NC
J10
Pwr
Remove this J10 jumper only if Fire Panel or Smoke Detection system is connected to the (Fire P) terminal.
External Speaker
8Ω, 1.5W (Optional)
CM-1200
Key Switch
(Optional)
Mode: 15 and 30 Seconds
Door armed and locked in 15 or 30 seconds mode
Mode: Bypass
Door unlocked (Either Bypass or R-exit)
Mode: Bypass
Installed: Factory default setting
Jumper J10 (Fire Panel Input)
Uninstalled: Only if a dry contact (NC) from a
fire alarm panel or smoke
detector system is connected to
the “Fire P” terminals.
Door unlocked & alarm sounding until reset
Display Mode
Jumper Settings
Push Bar (Optional)
CM-120i Keypad
(optional)
AC Main Fire Panel
2 Core Cable3 Core Cable
Power Supply
Push Bar (Ex-Trig)
Keypad Key Switch
Built-In
Key Switch
(Reset &
Bypass)
NO
NO
COM
COM
AUX Rly
Main Rly
NO
COM
GND
+12V
Lock Output not
to be used for
model CX-DE1200
Single Door Conguration
NOTE:
1) all eld-wiring to the unit
shall not exceed 30 m (98.5 ft)
in length.
2) all external power sources
shall be UL Listed with Class 2,
power-limited output.
Optional direct passthrough
for CX-DE1201 tandem lock
(Manual Reset
Or Bypass)

Page 4 of 9
CX-DE1200 Delayed Egress Electro Magnetic Lock
INSTALLATION INSTRUCTIONS
6. ARMATURE MOUNTING INSTRUCTIONS
Out Swing
DE1200-TEMPLATE with FB-DE1200-280 FOLD 90° ON THIS DOTTED LINE
Note: Dimensions might change if photocopied.
Place Against
Door Frame
FB-DE1200 Template
Drill 1/2"
Dia. for Cable
Access Hole
Install the mounting plate at 2
slots position first, then make
proper adjustment before
marking remaining screws
hole position.
Armature Housing-DE1200 Template
Place Against Door
Install the Armature Housing
with 2 screws position
first, then make proper
adjustment before marking
remaining screws hole position.
IG-DE1200-280 Ver.1019
Out-Swing
Door Only
Door Frame
Door Frame
Door Frame
Door Frame
Armature Plate
Armature Housing
Temporary mount with self tapping screw
EZ Interlocking
Mounting Plate
Screw #2
Screw #1
2. Drill mark the
screw hole
according to the
template holes
(Door & Frame)
Mounting Template
Door
1”
Door
Door
Door
Spring Armature Screw
Proxy
Trigger
Door
Step 1: Close the door, position the EM lock mounting location as close to the upper corner of the door with a minimum gap 1".
Step 2: Place the template against the door and frame and drill holes according to template indications.
Step 3: Place the mounting plate against the door frame and screw in according to the template holes position.
Step 4: Place the armature housing against the door and screw in according to the template holes position

Page 5 of 9
CX-DE1200 Delayed Egress Electro Magnetic Lock
INSTALLATION INSTRUCTIONS
Door Frame Door Frame Door Frame
Shoulder Screw
LOCK
Figure:1 Figure:2
Fixing Screw
Fixing Screw
EZ Mount Interlock
Mounting Plate Assembly
Figure:3
LOCK LOCK
1
2
Door
Out Swing Out Swing Out Swing
Door
Door Frame Door Frame
LOCK
Mount with self
tapping screw
permanently
Door
Door Frame
LOCK
Door
Out Swing
Door
Door
(Allen Key included)
Step 5: Slot in the electromagnet lock unit through the shoulder screw into the EZ mounting plate as shown in Figure 1-2 below.
CAUTION: The lock unit must be held in place until secured with xing screws.
Step 6: Align the lock unit with the mounting plate. Fix the lock unit to the mounting plate with the allen key given
through xing the screw. Carefully screw into the mounting plate to avoid stripping the threads. Check and conrm
the alignment and mating surface between the armature plate and lock unit.
NOTICE: Loosen screw #1 or #2 to re-align the mounting plate and position the lock unit mating surface to fully attach with
the armature plate. Re-tighten screw #1, #2 and screw-in the balance screw holes of mounting plate and armature housing.
Step 7: Pull the wires through the door frame, mounting plate and into the electromagnetic lock unit casing.
Fix the electromagnet lock unit to the mounting plate with the xing screw. Make sure to fully tighten the xing screw
with the proper tool (eg. "T" Handle Allen Key).

Page 6 of 9
CX-DE1200 Delayed Egress Electro Magnetic Lock
INSTALLATION INSTRUCTIONS
Step 8
After the lock unit has been mounted to the door and frame as per the provided template, route the wires through the access hole
and out to the controller board. Re-mount the lock front cover onto the lock. Make sure the proxy sensor is aligned with the hole on
the cover. The sensor height is factory default which slightly projected out from the surface cover.
CAUTION: Do not attempt to adjust the proxy sensor height, as this will result in damage to the sensor and void the warranty.
Step 9
Make all wiring connections to the lock controller board. Special precaution on the polarity of the input power terminals. This lock
has auto sensing voltage feature which automatically congures itself for 12 VDC or 24 VDC operation. Correct power supply voltage
must be used for proper lock operation.
NOTE: The length of wiring to all eld-wiring terminals shall not exceed 98.5 ft (30 m)
CAUTION: Input terminals for R-Exit, Reset & Ex-Trig must only be connected to a normally open momentary dry contact switch.
Connection to a voltage or "wet" output may damage the lock and void the warranty.
Step 10
Slowly swing the door closed and visually check the position of the proxy trigger as it approaches the proxy sensor on the lock. The
proxy trigger & sensor should align between one another either horizontally or vertically, if the installation was done perfectly using
the provided mounting template. The LED at the back of the proxy sensor will light on when the proxy trigger is detected.
IMPORTANT NOTICE: Standard operation of the lock depends on the proxy sensor being able to detect the proxy trigger when the
door is swing closed. A minor adjustment can be made to the proxy sensor height for ne tuning.
Step 11
Fine Tuning Proxy Sensor Height:
- Turning proxy sensor holder clockwise (CW) will increase the height of the proxy sensor from the front cover surface;
hence decreasing the gap between the sensor and proxy trigger.
- Turning proxy sensor holder counterclockwise (CCW) will decrease the height of the proxy sensor from the front cover surface;
hence increasing the gap between the sensor and proxy trigger.
Step 12
Fine Tuning Door Movement Detection Sensitivity:
The proxy trigger is spring loaded and can be screwed in or out from the proxy trigger ABS housing using the provided Allen key M5.
Hence, increase or decrease the gap between the sensor and proxy trigger.
IMPORTANT NOTICE: Standard installation of the proxy sensor and proxy trigger does not have to touch each other physically to
operate correctly.
PROXY SENSOR
PROXY SENSOR HOLDER
DOOR
CW
CCW
PROXY TRIGGER
Release Time:
The Release time can be selectable either 15 or 30 seconds. The Nuisance time delay is included in the door Release cycle and the
total time to unlock the door remain the same as per setting once sensor is triggered.
Nuisance Time:
The Nuisance time feature is a warning time delay that commences when pressure is applied to outward swinging doors. Releasing
the door before the end of the nuisance time, will turn o the warning alarm buzzer and reset nuisance time to origin. Nuisance
time is eld selectable for 1, 2 or 3 seconds. Triggering the proxy sensor beyond the nuisance time will start the irreversible Release
cycle time. The Nuisance time is included in the lock Release time cycle.

Page 7 of 9
CX-DE1200 Delayed Egress Electro Magnetic Lock
INSTALLATION INSTRUCTIONS
R-Exit Time:
The Request Exit (R-Exit) time is eld selectable for 1, 15, 20, or 30 seconds. The R-Exit time is the duration for the lock that will
remain Unlocked (Bypass), after a remote normally open contact switch is momentarily activated. When activated with an access
control system, the R-Exit time cycle will start after the access control relay open time expires. The door will automatically re-lock if
the door is opened, then closed during the R-Exit time cycle.
Trigger Type:
The trigger type is eld selectable either EXTERNAL or INTERNAL. Selecting INTERNAL mode uses the built-in proxy sensor and EX-
TRIG terminal to trigger the Release Time cycle. Selecting External mode will disable the INTERNAL mode sensor; activation of the
Release Time cycle is triggered by an external egress device equipped with a normally open contact switch.
Start-Up State:
The Start-Up selection, imply the state of lock during restoration of power up. It is eld selectable either be LOCKED or UNLOCKED.
In the LOCKED mode, the lock will be reset to secure mode. In the UNLOCKED mode, the lock will remain unlocked and the LED Bar
display will indicate as per By-Pass mode. To reset the lock; a momentarily normally open contact to the RESET signal will re-lock the
door. This feature selection is to comply with building code requirements in jurisdictions that require manual reset or re-lock upon
loss and restoration of system power supply.
Warning Type:
The warning type is eld selectable either TONE or VOICE. In secure status, the LED Bar displays a 15 segment or 30 segment LED
light. Each segment represents. Upon activation of the irreversible Release Time cycle, the LED Bar segment display begins to turn
o one by one. In VOICE mode, the countdown will be counted along with verbal exit guidance. When the LED bar display reaches
zero, the lock will release. The verbal voice guidance changes to a continuous verbal instruction announcing, "Door Unlocked". In
TONE ONLY mode, the countdown will be accompanied with a beeping tone only, and a continuous tone is heard once the Release
time cycle ends.
Languages:
The voice message can be in 3 languages which are eld selectable. The languages are English (Default), French and Spanish.
Voice Type:
For English only, the voice type is eld selectable for either a male or female voice.
Examples:
- 15 seconds Mode: "Door will unlock in 15 seconds; Door will unlock in 5 seconds; Door unlocked..."
(Both messages repeat "Door unlocked" until the lock is reset).
- 30 seconds Mode: "Door will unlock in 30 seconds; Door will unlock in 20 seconds; Door will unlock in 10 seconds;
Door will unlock in 5 seconds; Door unlocked..." (Both messages repeat "Door unlocked" until the lock is reset).
Door POS Alarm (DPA):
- DPA Active: The lock will enter alarm mode when the door is held open past the R-Exit time period triggering a buzzing tone or
alarm voice and the DPA can be Reset by the built-in key switch or remote reset.
- DPA Inactive: The lock will enter stand-by mode which will remain unlocked if the door is held open past the R-Exit time set.
No warning sound is emitted. The Lock can re-lock upon closure of the door.
Anti-Pass Back
If door doesn't open after the count down, the door will re-lock after a set time frame: 1 or 5 seconds.
Dip Switch Position ON
1 2 3 41 2 3 4 5 678
DIPON DIP ON
OFF
ON
OFF
Note:
Only English version
has a Female Voice.
Voice Type
ON : Male
OFF : Female
Warning Type
ON : Voice
OFF : Tone
Languages
ON - ON : French
OFF - OFF : English
OFF - ON : Spanish
ON - OFF : French (Standby)
Anti Pass Back
ON : 1s
OFF : 5s
Release Time
ON : 30 seconds
OFF : 15 seconds
Nuisance Time
ON : 2 seconds
OFF : 1 second
R-Exit Time
ON - ON : 1s
OFF - OFF : 15s
ON - OFF : 20s
OFF - ON : 30s
Door POS Alarm (DPA)
ON : Alarm Mode
OFF : Standby Mode
Start-up State
ON : Locked
OFF : Unlocked
Trigger Type
ON : External
OFF : Internal

Page 8 of 9
CX-DE1200 Delayed Egress Electro Magnetic Lock
INSTALLATION INSTRUCTIONS
7. CONFIGURATION
Conguration
Options
Delay
Release
Nuisance
Delay Request to Exit Period Trigger Type
Power-Up
State
Door Prop
Open
Anti-Pass
Back
Reset After
ALARM
Switch 1 Switch 2 Switch 3 4 Switch 5 Switch 6 Switch 7 Switch 8
N1 15 OFF 1OFF 1 Sec ON ON Internal OFF Unlocked OFF Stand-
by OFF 5OFF
Fixed Manual
30 ON 2ON 15 Sec OFF OFF External ON Locked ON Alarm ON 1ON
All options selectable
20 Sec ON OFF
30 Sec OFF ON
N2 15 Not
Used
0OFF 1 Sec ON ON Internal OFF Unlocked OFF Stand-
by OFF 5OFF
Fixed Manual
15 1ON 15 Sec OFF OFF External ON Locked ON Alarm ON 1ON
NFPA Compliant
20 Sec ON OFF
30 Sec OFF ON
N3 30 Not
Used
0OFF 1 Sec ON ON Internal OFF Unlocked OFF Stand-
by OFF 5OFF
Fixed Manual
30 1ON 15 Sec OFF OFF External ON Locked ON Alarm ON 1ON
NFPA Compliant
20 Sec ON OFF
30 Sec OFF ON
N4 15 Not
Used
0OFF 1 Sec ON ON Internal OFF Unlocked Not
Used
Stand-
by OFF 5OFF
Fixed Manual
15 1ON 15 Sec OFF OFF External ON Unlocked Alarm ON 1ON
NFPA/OSHPD Compliant. Power Up
unlocked and manual reset is xed.
20 Sec ON OFF
30 Sec OFF ON
Not Used Switch 8
B1 15 Not
Used
0OFF 1 Sec ON ON Internal OFF Unlocked OFF Stand-
by OFF Manual OFF
15 3ON 15 Sec OFF OFF External ON Locked ON Alarm ON Auto ON
BOCA Compliant. Automatic alarm reset
after 30 continuous seconds
from door closure.
20 Sec ON OFF
30 Sec OFF ON
B2 30 Not
Used
0OFF 1 Sec ON ON Internal OFF Unlocked OFF Stand-
by OFF Manual O
30 3ON 15 Sec OFF OFF External ON Locked ON Alarm ON Auto ON
BOCA Compliant. Automatic alarm reset
after 30 continuous seconds
from door closure.
20 Sec ON OFF
30 Sec OFF ON
B3 15 Not
Used
0Not
Used
1 Sec ON ON Internal OFF Unlocked OFF Stand-
by OFF Manual OFF
15 015 Sec OFF OFF External ON Locked ON Alarm ON Auto ON
BOCA/Chicago Compliant. 0 sec
nuisance. Automatic alarm reset after 30
continuous seconds from door closure.
20 Sec ON OFF
30 Sec OFF ON
ITEM
NUMBER QTY DESCRIPTION
1 1 MOUNTING PLATE
2 1 ELECTRO MAGNETIC LOCK SCREW PACKAGING
8. PARTS REPLACEMENT

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
Page 9 of 9
CX-DE1200 Delayed Egress Electro Magnetic Lock
INSTALLATION INSTRUCTIONS
CX-DESPK15
15 Watt
Speaker
Plug in
Power Supply
12 VDC
PWR
+
_PWR
+
_GRN Rly
NO C NC
RED Rly
NO C NC
Ex-Trig
NO C
Reset
NO C
R-Exit
NO C
Bypass
NO C
+
_
__
_
++
GND
INL
+
CX-TRP-612DC
CM-1100/7212
Remote
Reset Station
Ex.Spkr
+_PWR
+
_PWR
+
_
Ex.Spkr
+_PWR
+
_PWR
+
_
Lock
+
_
Fire P
C NC
Lock
+
_
Fire P
C NC
CM-DE502SO
Remote
Audible-Visual
Station
PWR
+
_PWR
+
_GRN Rly
NO C NC
RED Rly
NO C NC
Ex-Trig
NO C
Reset
NO C
R-Exit
NO C
Bypass
NO C
Red
Green
B
CM-DESPK
Remote
Audio
Annunciator
+
_
9. ACCESSORIES WIRING
10. COMPLETE WIRING OPTIONS AND FUNCTIONS
File: CX-DE1200_Manual_R3.indd
Rev/Date.: 2/11/25/21
Part no.: 40-82B236
Page 6
Terminal Descriptions
Ex. Spkr PWR
+-
NO C NC
+ -
Fire P
C NC Lock GRN Rly RED Rly Ex-TrigReset R-Exit Bypass
+-NO CNC NO C NO CNO C NO C
Wire to
External
Speaker
(CX-DESPK
or
CX-DESPK15) Power
Supply
Input
12/24 DC
+/- 10%
Lock
Secure
Output
Alarm
Output
Remote
LockReset
Input
(Wire to
CM-DESPK)
Remote
Request to
Exit
(Wire from
remote key
switch)
Instant Bypass
Overide Input
PWR DPS
NO C NC Bond-S
NO CNC
ATS
NO CNC
Door
Position
Status
(This contact
will change
state when the
maglock is
NOT on the
armature)
Anti Tamper
Switch
(This contact
will change
state when the
cover is
removed.)
External
Trigger
(Wire from of
Tandem
CX-DE1220
lock.)
+-
Power
Supply for
accessories
Fire Alarm
Input
(Supervised,
Normally
Closed)
[J10 jumper
must be
removed]
Wire
connection
to Tandum
Lock
CX-DE1220
Lock Status
(The bond
sensor will
monitor the
surface of the
armature. This
contact will
change state
when the
electromagnetic
lock is not
generating full
holding
potential.)
Both contacts will be triggered during the
countdown before the maglock is
de-engergized and released.
(The contact
will change
state when
the maglock
coil is
energized or
not
energized.)
(The contact
will change
state when
the alarm
has been
triggered by
a person
pressing on
the door to
exit.)
WARNING: Improper installation, maintenance, inspection or usage of the product or any related accessories or parts may cause the electromagnetic lock, armature
plate and associated hardware to disengage and fall, causing serious bodily injury and property damage. Camden will not be liable to the installer, purchaser, end
user or anyone else for damage or injury to person or property due to improper installation, care, storage, handling, maintenance, inspection, abuse, misuse or act of
God or nature involving this product or any related accessories or parts. The delayed egress device should be routinely checked for proper operation and compliance
with re and building codes. Refer to maintenance document #40-82B292 for additional information.