CAMDEN CM-30E User manual

Electrified Locks, Relays and Timers
CM-30E
Exit Switch
INSTALLATION INSTRUCTIONS
Page 1 of 2
1. GENERAL DESCRIPTION
Camden CM-30 series illuminated Exit switches are designed to
mount into a deep style single gang electrical box. The large 2” square
translucent button is easy to push. One momentary micro switch is
provided with Form C output, rated at 10 amps@125 VAC. CM-30E
supplied with a 12V DC long-life LED.
3. MOUNTING
NOTES:
If CM-30E will be used with 24V DC, the supplied in-line resistor, must
not be removed.
IMPORTANT:
Leave resistor on for 24 Volts,
Cut o resistor for 12 Volts
2. SPECIFICATION
Models CM-30E
Lens Color Green Lens
Legend “Push to Exit”
Size 4.5”H x 2.75”W x 2”D
Mounting 2 x #6-32 machine screws
Switch Rating 10 Amps @ 125 VAC
LED Models 100,000 hours
Voltage Required 12 V or 24 V DC ONLY
1. Push the color-coded leads onto the switch terminals (if not already
installed), as per the enclosed diagram. If illumination is not required,
the Red & Black wires can be removed.
2. Connect the appropriate wires to your devices. Tuck wiring into box,
and fasten switch plate using screws provided.
4. WARRANTY
Camden Door Controls guarantees the CM-30 to be free from
manufacturing defects for 3 years from date of sale. If during the rst
3 years the CM-30 fails to perform correctly, it may be returned to our
factory where it will be repaired or replaced (at our discretion) without
charge. There is no warranty for LED damage due to over voltage!
Except as stated herein, Camden extends no warranties expressed or
implied regarding function, performance or service.
Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
File: CM-30E_Manual.indd
Rev.: Nov 06, 2023
Part No.: 40-82B086
THIS PACKAGE INCLUDES:
1 x Exit Switch
1 x Plain Ziploc Bag
1 x 6” Black Wire Female Flag Connector
1 x 6” Red Wire Harness
1 x 6” Orange Wire Female Flag Connector
1 x 6” Blue Wire Female Flag Connector
1 x 6” Grey Wire Female Flag Connector
2 x 6-32 x 3/4” Phillips Oval Head Screws
5 x Grey Plastic Wire Nut
2 x 6-32-3/4” Snake Eye Tamper Proof Screws
1 x Key for Snake Eye Tamper Proof Screws
1 x Installation Manual

Page 2 of 2
FILENAME: CM-30 Diagram.vsd
DRAWING No: DRG-CM30-022503
CM-30 Switch Wiring Diagram
SCALE: NONE DRAWN BY: DGW REVISED: 03/20/08DATE: 02/25/03
Camden Manufacturing
2395 Skymark Avenue
Mississauga, Ontario
L4W 4Y6
12 - 24 V
AC/DC
Power
for Light
Common Normally
Open
Normally
Closed
Orange
Blue
Grey
Red lackB
Rear View of CM-30 switch
and Faceplate
NOTE: Access to light bulb (or LED) is obtained by first
removing Cherry switch from two plastic retaining
pins. Squeeze white retainer assembly between
finger and thumb, and gently rock back and forth
while pulling free of black threaded portion. Then
pull out light bulb (or LED) to replace.
Note: A lead with blue-coloured heat
shrink (over in-line resistor) is
supplied on LED model.
A lead with black coloured heat
shrink (over in-line resistor) is
supplied on incandescent bulb model. Leave resister on for 24 Volts,
Cut off resister for 12 Volts.