CAMDEN ValueWave CM-221 Series User manual

Page 1 of 6
CM-221M
Touchless Exit Switch with Remote LED Triggering
INSTALLATION INSTRUCTIONS
Door Activation Devices
1. GENERAL DESCRIPTION
The CM-221M Hands-Free Switch uses active infra-red
microburst sensor technology, designed for use in ADA
compliant automatic door control applications and access
control.
The CM-221M switches eliminate the spread of germs by
avoiding physical contact, and provide greater convenience
when moving through the premises. The switches are available
with stainless steel faceplates, in narrow (jamb) or single gang.
All models are ROHS compliant with lead-free construction.
Built-in remote LED switching allows for integration with
third-party applications, such as guard and nurse station
annunciators. Adjustable time delay from 0.5 to 20 seconds
and an adjustable range from (2” to 8” / 5cm to 20cm).
2. SPECIFICATIONS
Voltage 12 to 24 VDC +/- 10%
Current 45 mA (peak)
PIR Contact Rating 1 Amp @ 30 VDC
PIR Contacts Common/ N.O./ N.C.
Temperature Range 14F to 122F (-10 to 50 °C)
Response Time 10ms
Pushbutton
Contact Rating 1 Amp, 30 VDC
Pushbutton
Contacts Common/N.O./N.C
3. FEATURES
• Built-in Red and Green LED indication.
Factory default = Red (Standby), Green (Triggered)
• Red and Green LEDs can be controlled by sensor or
externally
• Adjustable detecting distance: 2 to 8 Inches (5 cm to 20 cm)
• Adjustable Time Delay: 0.5 seconds to 20 seconds
• Toggle function selection available
• IP65 rating
• IR lens to provide stable and reliable operation
4. OPERATION AT A GLANCE
In a typical application, as you approach the CM-221, the LED
will be red. When you wave your hand in front it will change
the LED to green, and trigger its relay to change state and
unlock your door, or trigger the door operator to open the
door. The toggle feature can be used to trigger the door to
remain in the unlocked position, until you wave your hand a
second time to relock it.
PARTS INCLUDED IN THE BOX
• (1) CM-221M Touchless Exit Switch with Manual Override pushbutton
• (1) Parts bag (Contents: (2) 6-32 X 1/2" oval head Phillips ss screws, (2) 6-32 X 1/2" snake eye s/s at head
screws, (1) Key for tamper proof screws (snake eye), (1) Jumper for factory external LED control)
• (1) User/Installation Manual
• (1) Faceplate Gasket
NOTE: Do NOT use AC Voltage for this unit.
Please see section 8 for power requirements
Dimensions
Narrow:
1 3/4" W x 4 1/2" H x 1 1/4" D
(43 mm x 114 mm x 31 mm)
Single Gang:
2 3/4" W x 4 1/2" H x 1 1/4" D
(70 mm x 114 mm x 31 mm)

Page 2 of 6
CM-221M TOUCHLESS EXIT SWITCH
INSTALLATION INSTRUCTIONS
Adjustment for time delay
(0.5 to 20 seconds) For Toggle.
Turn clockwise to increase
time delay
Adjustment for distance
(2" to 8", 5 to 20 cm)
Turn clockwise to
increase range
MODE PINS:
OPEN (Default position)=
Internal mode where the LED
colours will be controlled by
the IR sensor.
SHORTED = External mode
where the LED colours will be
controlled by Yellow and
White wires.
- +
5. CONFIGURING THE CM-221M
Range of Detection and Output Duration
Looking at the back of the CM-221M with the Mode pins located at the top, you will see two adjustment potentiometers. The one
on the left can be turned clockwise to set the range of detection (2” to 8” / 5cm to 20cm), and the one on the right will set the
duration of the output (0.5 to 20 seconds).
If the output needs to be triggered and maintained in that state until triggered once more, then the Toggle feature can be used by
turning the output duration adjustment potentiometer to the fully clockwise position.
Remote LED Switching
The CM-221M can also have its LED states controlled remotely. This is done by installing the supplied jumper from the parts
bag onto the two pins on the back of the unit. Once installed the green and red LED’s can be triggered to change by bringing
either one low (to ground). The yellow wire controls the green LED, whereas, the white wire controls the red LED. They can be
individually turned on or o, or they can be wired to a SPDT contact to turn red on and green o, or vice versa.

Page 3 of 6
CM-221M TOUCHLESS EXIT SWITCH
INSTALLATION INSTRUCTIONS
6. WIRING THE CM-221
1. Connection to a Maglock
Connect the ground (-) of the maglock to the ground (-) of the VDC power supply. Next connect the (+) of the maglock to the
(N.C.) of the manual pushbutton. Connect the common (com) of the manual pushbutton to the PIR sensor purple wire (normally
closed.) Jumper the PIR sensor blue (common) and red (power +) wires and then connect them to the (+) positive terminal of the
DC power supply. Wire the PIR sensor black (-) wire to the negative (-) terminal of the DC power supply.
‐+
CX‐PS13PowerSupply
12or24VDC
B‐B+DC‐DC+ACAC
CX‐TRTransformer
12,16or24VAC
120VAC
JumpermustbeOFF,thetwo
pinsarenotshorted
CAUTION:All
unusedwire
conductors
shouldbe
individually
isolatedand
taped.
CM‐221MTouchlessSwitchwithmanualpushbuttonwiredtomaglock
Maglock
+
‐
7654321
7Wirecoloredwireharness
# Color Function
1 Red 12to24VDC
2 Black 0VDC(Ground)
3 Yellow GreenLEDcontrolledbyexternalmode.
4 White RedLED,controlledbyexternalmode.
5 Green Relay:NormallyOpen
6 Blue Relay:Common
7 Purple Relay:NormallyClosed
N.O.
N.C.
COM
3Wirecoloredwireharness
# Color Function
1 Red Common
2 Black NormallyOpen
3 White NormallyClosed
WHT
RED
BLK

Page 4 of 6
CM-221M TOUCHLESS EXIT SWITCH WITH REMOTE LED TRIGGERING
INSTALLATION INSTRUCTIONS
‐+
CX‐PS‐13PowerSupply
12or24VDC
B‐B+DC‐DC+ACAC
CX‐TRTransformer
12,16or24VAC
120VAC
JumpermustbeOFF,
thetwopinsmustnot
beshorted.
CAUTION:Allunused
wireconductors
shouldbeindividually
isolatedandtaped.
CM‐221MTouchlessSwitchwiredtodoorstrike
‐
+
FailLockedStrike
MOV
7654321
7WireIRsensorcoloredwires
# Color Function
1 Red 12to24VDC
2 Black 0VDC(Ground)
3 Yellow GreenLEDcontrolledbyexternalmode.
4 White RedLED,controlledbyexternalmode.
5 Green Relay:NormallyOpen
6 Blue Relay:Common
7 Purple Relay:NormallyClosed
N.O.
N.C.
COM
WHT
RED
BLK
ManualPush
Button
IRSensor
3WirePushbuttoncoloredwires
# Color Function
1 Red Common
2 Black NormallyOpen
3 White NormallyClosed
3. Connection to an External Strike
‐+
CX‐PS13PowerSupply
12or24VDC
B‐B+DC‐DC+ACAC
CX‐TRTransformer
12,16or24VAC
120VAC
Common
N.C
N.O
SPDTswitchto
remotelycontrolthe
greenandredLEDs.
JumpermustbeON,
shortingthetwopinsto
enableremoteselectionof
LEDcolors
CAUTION:Allunusedwire
conductorsshouldbe
individuallyisolatedandtaped.
CM‐221MTouchlessSwitchwiredtodooroperator.(RemoteLEDcontrol)
7WireIRsensorcoloredwires
# Color Function
1 Red 12to24VDC
2 Black 0VDC(Ground)
3 Yellow GreenLEDcontrolledbyexternalmode.
4 White RedLED,controlledbyexternalmode.
5 Green Relay:NormallyOpen
6 Blue Relay:Common
7 Purple Relay:NormallyClosed
7654321
N.O.
N.C.
COM
WHT
RED
BLK
IRSensor
ManualPush
Button
3WirePushbuttoncoloredwires
# Color Function
1 Red Common
2 Black NormallyOpen
3 White NormallyClosed
2. Connection to a Door Operator
‐+
CX‐PS13PowerSupply
12or24VDC
B‐B+DC‐DC+ACAC
CX‐TRTransformer
12,16or24VAC
120VAC
Common
N.C
N.O
SPDTswitchto
remotelycontrolthe
greenandredLEDs.
JumpermustbeON,
shortingthetwopinsto
enableremoteselectionof
LEDcolors
CAUTION:Allunusedwire
conductorsshouldbe
individuallyisolatedandtaped.
CM‐221MTouchlessSwitchwiredtodooroperator.(RemoteLEDcontrol)
7WireIRsensorcoloredwires
# Color Function
1 Red 12to24VDC
2 Black 0VDC(Ground)
3 Yellow GreenLEDcontrolledbyexternalmode.
4 White RedLED,controlledbyexternalmode.
5 Green Relay:NormallyOpen
6 Blue Relay:Common
7 Purple Relay:NormallyClosed
7654321
N.O.
N.C.
COM
WHT
RED
BLK
IRSensor
ManualPush
Button
3WirePushbuttoncoloredwires
# Color Function
1 Red Common
2 Black NormallyOpen
3 White NormallyClosed
‐+
CX‐PS‐13PowerSupply
12or24VDC
B‐B+DC‐DC+ACAC
CX‐TRTransformer
12,16or24VAC
120VAC
JumpermustbeOFF,
thetwopinsmustnot
beshorted.
CAUTION:Allunused
wireconductors
shouldbeindividually
isolatedandtaped.
CM‐221MTouchlessSwitchwiredtodoorstrike
‐
+
FailLockedStrike
MOV
7654321
7WireIRsensorcoloredwires
# Color Function
1 Red 12to24VDC
2 Black 0VDC(Ground)
3 Yellow GreenLEDcontrolledbyexternalmode.
4 White RedLED,controlledbyexternalmode.
5 Green Relay:NormallyOpen
6 Blue Relay:Common
7 Purple Relay:NormallyClosed
N.O.
N.C.
COM
WHT
RED
BLK
ManualPush
Button
IRSensor
3WirePushbuttoncoloredwires
# Color Function
1 Red Common
2 Black NormallyOpen
3 White NormallyClosed
‐+
CX‐PS13PowerSupply
12or24VDC
B‐B+DC‐DC+ACAC
CX‐TRTransformer
12,16or24VAC
120VAC
Common
N.C
N.O
SPDTswitchto
remotelycontrolthe
greenandredLEDs.
JumpermustbeON,
shortingthetwopinsto
enableremoteselectionof
LEDcolors
CAUTION:Allunusedwire
conductorsshouldbe
individuallyisolatedandtaped.
CM‐221MTouchlessSwitchwiredtodooroperator.(RemoteLEDcontrol)
7WireIRsensorcoloredwires
# Color Function
1 Red 12to24VDC
2 Black 0VDC(Ground)
3 Yellow GreenLEDcontrolledbyexternalmode.
4 White RedLED,controlledbyexternalmode.
5 Green Relay:NormallyOpen
6 Blue Relay:Common
7 Purple Relay:NormallyClosed
7654321
N.O.
N.C.
COM
WHT
RED
BLK
IRSensor
ManualPush
Button
3WirePushbuttoncoloredwires
# Color Function
1 Red Common
2 Black NormallyOpen
3 White NormallyClosed
‐+
CX‐PS‐13PowerSupply
12or24VDC
B‐B+DC‐DC+ACAC
CX‐TRTransformer
12,16or24VAC
120VAC
JumpermustbeOFF,
thetwopinsmustnot
beshorted.
CAUTION:Allunused
wireconductors
shouldbeindividually
isolatedandtaped.
CM‐221MTouchlessSwitchwiredtodoorstrike
‐
+
FailLockedStrike
MOV
7654321
7WireIRsensorcoloredwires
# Color Function
1 Red 12to24VDC
2 Black 0VDC(Ground)
3 Yellow GreenLEDcontrolledbyexternalmode.
4 White RedLED,controlledbyexternalmode.
5 Green Relay:NormallyOpen
6 Blue Relay:Common
7 Purple Relay:NormallyClosed
N.O.
N.C.
COM
WHT
RED
BLK
ManualPush
Button
IRSensor
3WirePushbuttoncoloredwires
# Color Function
1 Red Common
2 Black NormallyOpen
3 White NormallyClosed

Page 5 of 6
CM-221M TOUCHLESS EXIT SWITCH WITH REMOTE LED TRIGGERING
INSTALLATION INSTRUCTIONS
7. POWER
The CM-221M is a VDC device only and will accept a range of VDC power from 12VDC to 24VDC (+/- 10%). Do not connect AC
voltage to the CM-221M at any time.
Note: A linear output VDC power supply is strongly recommended. If using power from other than Camden’s CX-PS13 ltered
regulated power supply, you must measure the provided power before applying power to the CM-221M. Voltages of more
than 10% over the specied acceptable range or using a power supply with large amounts of AC voltage on it (unltered
unregulated power such as a transformer and a rectier) may damage the CM-221M and void the warranty.
13
4"
[43mm]
11
8"
[28mm]
11
8"
[28mm]
41
2"
[114mm]
1
4"
[5mm]
21
4"
[57mm]
23
4"
[70mm]
41
2"
[114mm]
21
4"
[57mm]
1"
[26mm]
WAVE
TO EXIT
OVERRIDE OVERRIDE
WAVE
TO EXIT

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
Page 6 of 6
CM-221M TOUCHLESS EXIT SWITCH
INSTALLATION INSTRUCTIONS
File: CM-221M_Manual.indd
Revision: 04/04/22
Part No.: # 40-82B308
ORDERING INFORMATION FOR REPLACEMENT PARTS
ITEM NUMBER PART NUMBER DESCRIPTION
1. 60-31A083 TOUCHLESS SENSOR SWITCH WITH EXTERNAL LED CONTROL
2. A 60-49B040-xxx NARROW STAINLESS-STEEL FACEPLATE
B 60-49H009L-xxx SINGLE GANG STAINLESS-STEEL FACEPLATE
3. A 60-59H000 GASKET FOR NARROW GANG TOUCHLESS SWITCH
B 60-59H001 GASKET FOR SINGLE GANG TOUCHLESS SWITCH
PARTS KIT
ITEM NUMBER PART NUMBER DESCRIPTION
4 60-34B093
(A) 6-32 X 1/2” OVAL HD PHILLIPS SS SCREW
(B) 6-32 X 1/2” SNAKE EYE SCREW
(C) KEY FOR TAMPER SNAKE EYE SCREW
5 60-68D05768D057 METAL PUSHBUTTON
COMPATIBLE MOUNTING BOXES OPTION
ITEM NUMBER
PART NUMBER
DESCRIPTION
FOR SINGLE GANG
CM-34AL SURFACE BOX, STANDARD DEPTH, THREADED CONDUIT ENTRY. HEAVY DUTY CAST ALUMINUM
2 3/4”W x 4 1/2”H x 1 3/4”D (70mm x 114mm x 45mm)
CM-34BL ONE GANG BLACK ABS BOX, SURFACE MOUNT
2 7/8’’W x 4 5/8’’H x 1 3/4’’ D (73mm x 117mm x 44mm)
CM-66 FLUSH BOX & DRESS PLATE, STANDARD DEPTH BOX WITH 7’’ x 7’’ (178mm x 178mm) DRESS PLATE
HEAVY GAUGE STAINLESS STEEL
FOR MULLION
CM-23D SURFACE BOX WITH EXTRA DEPTH, FLAME, AND IMPACT RESISTANT BLACK POLYMER (ABS)
1 3/4” W X 4 1/2”H X 1 3/4”D (46MM X 117MM X 43MM)
1
4
2A
2B
3A
3B
4C
4B
4A
5