CAMDEN CM-9800 User manual

Page 1 of 5
CM-9800
Touch Button Switch
INSTALLATION INSTRUCTIONS
Door Activation Devices
SL NO Component Name Quantity
1Wall plug 6mm 3
2Wall xing screw 4 x 30mm 3
33 x 6 Security Screw 1
4IN4007 diode 1
5470nf Capacitor 1
610K Res 1/2w 1
7Security screw driver 1
86-32 x 1" Machine screw 2
9Mounting Template 1
1. GENERAL DESCRIPTION
CM-9800 is a request-to-exit switch, It will work independently
(standalone) or can equally be connected via a controller to
provide exit from a secured area (Push Button Input). With its
slim looks and die-cast metal body, the CM-9800 combines
elegance and aesthetics with ruggedness and reliability.
2. SPECIFICATIONS
Input Voltage 12-24V AC/DC
Current
Consumption max.65mA
Relay Output 2A at 24V DC / 120V AC
Set Relay Time 0.5 to 60 seconds or Toggle (ON/OFF)
Indicators-LED Orange, red, green
LED Control Yes, by DIP switch
Tamper Yes
Backlight ON/OFF Yes, by DIP switch
Buzzer ON/OFF Yes, by DIP switch
Operating
Temperature -4°F to 122°F (-20°C to 50°C)
Operating Humidity Non-condensing up to 95%
Housing Die-cast Aluminium alloy
Touch Plate Mild Steel Painted
Protection IP66
Dimension 3.34” W x 4.5” L x 1/32” H
(85 mm x 116.6 mm x 22.6 mm)
3. MOUNTING
1. Identify a suitable location on wall or at surface.
2. Stick the Drilling Template provided on chosen location.
Drill 3 holes as indicated in the diagram.
3. Insert 3 nos. of 5 mm wall plugs provided into the drilled holes.
4. Route the cables through the holes provided in the
BackPlate.
5. Fix the Backplate rmly on the wall using 3nos. of 3 x 30mm
CSK screws
6. Connect wires.
7. After wiring, place the Housing over the xed backplate and
guide the slot into the backplate tab and slide it downwards.
8. Fix the Housing to the Back-Plate with a M3 x 6 mm Security
Screw on the bottom of the Housing using a Security
Screwdriver provided.
Important Note: Several layers of protection are provided
against transient voltages from static discharge, lightning
and power supply spikes. For protection to be fully effective,
earth grounding should be done correctly.
12/24 V
AC/DC
NC
COM
LR-
LG-
Tamp
Tamp
Tamper Switch
Tamper Switch
12 to 24VDC
12 to 24VAC
Red LED light
Green LED light
Normally closed
Common
NO
LED com
(GND)
Normally open
LED common
Grey
Color
Blue
Black &
Red
Orange
Yellow
Pink
White
Purple
Green
Red
Black
Green
Orange
Yellow
Pink
White
Purple
Grey
Blue
12/24V
AC/DC
LED com (GND)
LR -
LG -
NC
COM
NO
Tamp
Tamp Tamper
Relay 2A
Power Supply

Page 2 of 4
CM-9800 TOUCH BUTTON SWITCH
INSTALLATION INSTRUCTIONS
Access Control Device
NO Purple
White
COM
NC
12/24V
AC/DC
Request-to-exit
Input
Relay output
Locking Device
Red
Black
12/24V
AC/DC
Power Supply
~ ~
10K 1/2W
470nF
~
~
NO Purple
White
COM
NC
12/24V
AC/DC
Red
Black 12/24V
AC/DC
Power Supply
NO
COM
NC
12/24V
AC/DC
- +
+
-
Red
Black
White
Pink
12/24V
AC/DC
CONNECTION TO ACCESS CONTROL PANEL
OUTPUT CONNECTION FOR DC DEVICE - FAIL OPEN
OUTPUT CONNECTION FOR AC DEVICE - FAIL SECURE

Page 3 of 4
CM-9800 TOUCH BUTTON SWITCH
INSTALLATION INSTRUCTIONS
DIP SWITCH SETTINGS
1 – Relay Time (0.5 to 60 seconds or toggle mode)
2 – not used
3 – Buzzer ON/OFF
4 - Backlight ON/OFF
5 - LED Control
6 – Default state – State of the controller's input for the LEDs
SET RELAY TIMER – DIP SWITCH 1
CM-9800 operates in Toggle or Pulse mode. The time is set by
Dipswitch 1 Setting.
Put the Switch 1 in position ON. The unit will start emitting
beeps. Count the beeps and then stop them by positioning the
Switch 1 to OFF. The number of beeps denes the relays time,
according to the table below (2 beeps - 0.5 sec, 3 beeps - 1 sec...).
Switch 1 Number of Beeps Time
ON 1 beep Toggle Mode
(ON/OFF Mode)
ON 2 beeps 0.5 Seconds
ON 3 beeps 1 Seconds
ON 4 beeps 2 Seconds
ON 5 beeps 5 Seconds
ON 6 beeps 10 Seconds
ON 7 beeps 15 Seconds
ON 8 beeps 30 Seconds
ON 9 beeps 45 Seconds
ON 10 beeps 60 Seconds
ON
1 2 34 5 6
ON
1 2 34 5 6
DIP SWITCH 1 RELAY TIME
BUZZER, BACKLIGHT AND LED CONTROL
Position 3, 4, 5, and 6 On Dip Switch
Example of externally controlled LED light, where the exit
button's light follows the reader's light.
ON
1 2 34 5 6
LR-
LED Red
LED Green
LED COM
LG-
LED Red
LED Green
LED com (Ground)
Access Control Panel

Page 4 of 4
CM-9800 TOUCH BUTTON SWITCH
INSTALLATION INSTRUCTIONS
SW3 Buzzer SW 4
Backlight
SW 5
LED Control
SW 6
Default State Relay Green-Yellow Wire
Red-Orange
Wire Backlight
ON ON -------
OFF OFF -------
--OFF OFF -ON --Green
--OFF OFF -OFF --No Light
--ON OFF -ON --Green
--ON OFF -OFF --Red
Default High
--ON ON OFF -Hi Hi Orange
--ON ON OFF -Low Hi Green
--ON ON OFF -Hi Low Red
--ON ON OFF -Low Low No Light
Default High
--OFF ON OFF -Hi Hi No Light
--OFF ON OFF -Low Hi Green
--OFF ON OFF -Hi Low Red
--OFF ON OFF -Low Low Orange
Default Low
--ON ON ON -Hi Hi No Light
--ON ON ON -Low Hi Green
--ON ON ON -Hi Low Red
--ON ON ON -Low Low Orange
Default Low
--OFF ON ON -Hi Hi Orange
--OFF ON ON -Low Hi Red
--OFF ON ON -Hi Low Green
--OFF ON ON -Low Low No Light

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
Page 5 of 4
CM-9800 TOUCH BUTTON SWITCH
INSTALLATION INSTRUCTIONS
File: CM-9800_Manual_Eng_R1.indd
Revision: June 1, 2019
Part No: #40-82B225
11
16''
[18mm]
13
16''
[21mm]
PUSH
TO
EXIT
33
8'' [86mm]
49
16''
[116mm]
31
4'' [83mm]
111
16'' [43mm]
11
8'' [28mm]
Ø3
16'' [4mm]
23
8'' [60mm]
11
2'' [37mm]
FRONT VIEW
SIDE VIEW
BACK VIEW