CAMDEN CM-336 User manual

Page 1 of 4
CM-336
Battery Operated Active Infra-Red “Hands-Free” Switches
INSTALLATION INSTRUCTIONS
Door Activation Devices
1. GENERAL DESCRIPTION
Sure-Wave™ Hands-Free switches are active infra-red devices
utilizing micro burst sensor technology, designed for use in
ADA compliant automatic door control applications. These
switches eliminate the spread of germs by avoiding physical
contact and oer building occupants greater convenience
when moving through the premises. Sure-Wave™ switches
are available with either stainless steel or impact resistant
polycarbonate faceplates, in narrow (jamb), single gang or
double gang congurations. All models are ROHS compliant
with lead-free construction.
2. APPLICATION
Sure-Wave™ battery powered hands-free switches are
American Disability Act (ADA) compliant, and provide
barrier free access and egress to buildings and washroom
facilities. Their rugged construction makes them ideal for
use on low-energy automatic doors, drive-up windows, and
interior and exterior doors in virtually any commercial (oce,
retail), institutional (school, hospital or clinic), or industrial
(manufacturing) facility.
Three standard face plate widths are available:
CM-336: 2 ¾” x 4 ½” polycarbonate or stainless steel, ts on
single gang electrical boxes.
CM-336/N: 1 ¾” x 4 ½” polycarbonate or stainless steel.
CM-336/W: 4 ½” x 4 ½” polycarbonate or stainless steel, ts on
single gang, double gang or 4 x 4 electrical boxes.
All faceplates may be ordered up with a plain face, with the
waving hand symbol (/40), with the waving hand symbol and
words: WAVE TO OPEN (/41) or with the waving hand, and
wheelchair icons plus words: WAVE TO OPEN (/42).
3. INSTALLATION
Mounting
Sure-Wave™ may be mounted in door jambs, single or double
gang electrical boxes, and 4 x 4 boxes.
NOTE: The sealing gasket (included) is recommended for
outdoor or wet locations. If using with Automatic doors install
in accordance with ANSI A156.10 / A156.19. Select from one of
the following three mounting subsections:
SINGLE GANG ELECTRICAL BOX: CM-336
1a - If using an in-wall box ensure the box is plumb and
square, and ush with the wall surface. (See Diagram 1)
1b - If using a surface box, ensure it is secure & plumb.
2- Using the dip switch located on the end of the unit, set the
operating mode. (See Section 4)
3- Attach the unit to the enclosure using the two #6-32 screws
provided.
4- Attach the faceplate to the unit using the two black
#6-32 x 3/8 machine screws or tamperproof screws.
Do not overtighten!!

Page 2 of 4
CM-336 BATTERY OPERATED ACTIVE INFRA-RED “HANDS-FREE” SWITCHES
INSTALLATION INSTRUCTIONS
Rough Wall
Finish
Recessed
Box
Unaligned
Box
Wall
Wall Box
Flush
Smooth
Wall Finish
2- GANG (or 4x4) ELECTRICAL BOX: CM-336W
1a - If using an in-wall box ensure the box is plumb and square,
and ush with the wall surface. (See Diagram 1)
1b - If using a surface box, ensure it is secure & plumb.
1c - If using a 4 x 4 box, ensure the box is plumb and square,
and ush with the wall surface, then attach the metal adaptor
plate (included in the CM-336W package) to the box using
appropriate fasteners.
2- Attach the unit to the enclosure using the two #6-32 screws
provided.
3- Attach the faceplate to the unit using the two black #6-32 x
3/8 machine screws or tamperproof screws.
Do not overtighten!!
Pairing the CM-336
The CM-336 battery operated wireless SureWave™ switch utilizes
our Lazerpoint RF technology and is for use with Camden CM-
RX90 V2, CM-RX91 or CM-RX92 Lazerpoint receivers.
To pair the CM-336 transmitter to a receiver, press the PB1 (or
PB2 on the CM-RX92) button on the receiver using a small blunt
object such as a small blade screwdriver or similar. Within 10
seconds, wave your hand in front of the CM-336 to activate it.
The Green LED Array on the receiver will ash once to conrm
enrollment. Repeat with any additional CM-336 wireless Sure-
wave™ switches. Activating the paired CM-336 again will signal
the receiver that you are nished programming and LED’s 1 &
2 will ash, in an alternating sequence. Activating the CM-336
a third time will activate the receiver’s relay and corresponding
LED, and also the device connected to the relay contacts.
If you wait longer than the 10 second period, the receiver will
time out of Pairing Mode and revert back to standby. The LED
will then ash to indicate the number of transmitters learned
into the receiver.
Wiring
CAUTION: Do not apply power to the unit until all wiring is
complete, and dip-switches have been set.
The CM-336 is powered from 2 AA batteries (supplied). The
battery holder has been pre-installed. Insert the batteries into
the battery holder. Please be careful that the polarity of the
batteries is correct.
Diagram 1 - Proper Box Installation
Diagram 2

Page 3 of 4
CM-336 BATTERY OPERATED ACTIVE INFRA-RED “HANDS-FREE” SWITCHES
INSTALLATION INSTRUCTIONS
4. APPLICATIONS & SET-UP APPLICATIONS
See Diagram 3 for the location of the Dip switches.
DIP Switch Settings
DIP Switch 1
Switch 1 – LED On/LED O
This switch disables the LED, should this feature be desired.
Factory setting is OFF. This feature will decrease the battery
life if set to ON.
Switch 2 – Audio Enable
Set this switch ON to enable an audible beep every time
the switch is activated. Factory default is OFF. Enabling this
feature will use additional power and decrease the life of the
battery.
CM-336 Description
1LED Enable Green LED ashes while the output is activated
2Audio Enable Piezo buzzer sounds when the output is activated
3Not Used
4Not Used
Battery Strength Meter
To check the battery strength, place an object in front of
the Surewave™ switch for approximately 5 seconds. The
Surewave™ switch will beep up to 5 times indicating the
battery charge level. 5 beeps being fully charged. 1-3 beeps
indicates you should change the batteries.
Adjustments
Once the Dip switches have been set, and the unit is installed
in the frame or enclosure, apply power to the unit and
observe operation.
Set both potentiometers to minimum setting initially
(fully counter-clockwise).
Adjust the range potentiometer by turning the pot in a
clockwise manner, and passing your hand in front of the unit.
Rotate the pot until the desired range is obtained.
See Diagram 3 for locations.
Diagram 3
1 LED Enable
2 Sounder enable
3 Not used
4 Not used
1
2
3
4
1
2
Activate LED
Error/
Alarm LED
Range Adj

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
Page 4 of 4
CM-336 BATTERY OPERATED ACTIVE INFRA-RED “HANDS-FREE” SWITCHES
INSTALLATION INSTRUCTIONS
File: CM-336_Manual.indd
Revised: 06/27/22
Part No: 40-82B311
5. SYSTEM INSPECTION INSTRUCTIONS
After the Installation and operational check of the system:
1. Place warning label on the door (as per ANSI A156.10 or
A156.19 guidelines). This will advise the person entering the
swing side zone that the door will move.
2. Instruct the owner on door system operation and how to
test it. This should be checked on a daily basis.
3. Instruct the owner on what to do if the door or any of its
components become damaged.
4. Strongly recommend to the owner that the complete entry
be inspected twice a year as part of the service agreement.
6. TECHNICAL DATA
No. of IR Sensors (1)
Batteries
(Supplied) (2) ‘AA’ Alkaline (Supplied)
Estimated Battery
Life 2 Years (Based on 100 Operations/Day)
Standard
Operating Range
1”- 12” (25.4mm - 304mm)
Factory Set to 6” (152mm)
Operating Mode Momentary
Inputs Request to Exit (to trigger the relay remotely or
from the other side of the door)
Wireless Output Built-in 915Mhz. Spread Spectrum
Wireless Transmitter
1’
0’ 2’ 3’
1”
(25.4mm)
12”
(304mm)
Diagram 4
Adjustable Range Settings