CAME AGT A200 User manual

AGTK200A03
AGT2K200A03
AGTK200A03E
FA01423-EN
EN
E
n
g
l
i
sh
AGT kit A200
AGTK200A03
AGT2K200A03
AGTK200A03E

AGT A200
HA/200
A/200R
HBP
HPC/1
AGTK200A03
HPC/2
AGT2K200A03
HTS HPC/1
AGTK200A03E
Page 2- Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
CONTENTS OF THE KIT
General precautions
• Read the instructions carefully before staring installation and performing any procedures as explained by the manufacturer.
• The installation, programming, commissioning and maintenance of the product must only be carried out by technicians who are
qualified and properly trained in compliance with the regulations in force, including as regards health and safety, and disposal of
packaging.
• The installer must ensure that the information for the user, where there is any, is provided and delivered.
• Before carrying out any cleaning or maintenance, disconnect the devices from the power supply.
• The equipment must only be used for the purpose for which it was expressly designed.
• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.
• Only use soft, dry or slightly damp cloths to clean the device. Do not use any chemical products.
• These instructions must be attached to the device.
The product complies with the relevant directives in force.
Dismantling and disposal. Dispose of the packaging and the device responsibly at the end of its life cycle, in compliance with
the laws in force in the country where the product is used. The recyclable components are marked with a symbol and the material
ID marker.
THE DATA AND INFORMATION IN THIS MANUAL ARE SUBJECT TO CHANGE AT ANY TIME AND WITHOUT ANY ADVANCE WARNING.
UNLESS OTHERWISE INDICATED, MEASUREMENTS ARE GIVEN IN MILLIMETRES.

M1
BP1
󱫀
503
󱤨󱤩
503
󱫂󱫄 󱫄
Page 3- Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Description
Internal audio receiver.
Door lock release button 󱫂
BP1 󱫀
Cut the jumper flush with BP1 to make the
door lock release button ( ) active only with
the handset raised.
Terminal board M1 󱫀
5 - Earth
7 - Call from entry panel input
8 - Audio FROM entry panel
9 - Audio TO entry panel
AGT A200
Technical data
Type AGT A200
Operating
temperature (°C) +5 to +40
Storage
temperature (°C) -25 to +70
IP Rating IP 30
Installation
• Open the device by pressing on the tab
at the bottom 󱫂.
• Separate the shell from the bottom of
the device.
• Fasten the bottom of the device to the
box on the wall 󱫄󱤨-󱫄󱤩-󱫄󱤪.
The box must be installed at an appro-
priate height for the user. Avoid over-
tightening the screws.
• Once all connections have been made,
reattach the shell to the bottom of the
device 󱫆.

Ø60
󱤪󱫆
64,5
70
145
43,5
45
7,5 57
70
106
󱫄
󱫀
Page 4- Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
A/200R
Description
A/200R guarantees the power supply to the HPC/1 entry panel and a maximum of 20 front plates with 6 buttons HPP/6.
It is provided with the following functions:
- 2 dual-tone call beeps for two entry panels (or for additional call, e.g. from the landing).
- Power supply and control for solenoid lock (12 V AC 1 A) via a relay (inside the device).
- Call generator: 2 types of dual-tone beep (up to 3 internal receivers can be connected in parallel on the same call). The device can
be powered at 12 V DC, for example by a battery or UPS (terminals +B and 5).
The device does not include an auxiliary-input protection device.

1
2
3
󱫂󱫄
Page 5- Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Function of terminals and jumpers
Terminal board A 󱫀
Network
Terminal board B 󱫀
+B Input 12 V DC 350 mA
5 Earth
21 Output 11 V DC
8 Common call output 1
8A Common call output 2
11 Audio from entry panel
12 Audio to entry panel
23 – Output 14 V AC
16 +
NO Normally open
relay contactsC Common
NC Normally closed
(*) The device is electronically protected against overloads and
short circuits.
Terminal board C 󱫀
5 Earth
8 Audio to internal receiver
9 Audio to internal receiver
Technical data
Type A/200R
Power supply 50-60 Hz (V AC) 230
Power consumption (VA) 34
Output voltages at 11 V DC (mA) 150
Output voltages at 14 V AC (mA) 650
Peak output voltages (mA) 300
Operating output voltages (mA) 650 (1A)
Storage temperature (°C) -25 to +70
Operating temperature (°C) 0 to +35
IP Rating IP30
Installation
• The device can be installed on DIN rails (EN 50022) on a suit-
able switchboard, or on the wall using the terminal covers.
☞Ensure that the power supply cables are appropriately fixed
in place, to avoid stresses, traction or twisting.
• To dismantle the device, proceed as shown in figure 2-3.
• See figure 1 for dimensions.
The power supply must always be installed horizontally.
Ensure there is correct ventilation if the power supply is
installed in a metal case.

Ⓐ
Ⓑ
󱫀
Page 6- Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
HA/200
Description
Audio module.
Functions of terminals and audio adjusters
Terminal board 󱫀
5 – power supply
21 + 12 V DC
8 common call (for call beep)
11 audio to internal receiver
12 audio from internal receiver
14 enable
In systems in which there is an enable command, terminal
14 can be connected to the earth (unit always active) or to
terminal 12 (unit active only when handset is raised).
Trimmers 󱫀
ⒶSpeaker audio
ⒷMicrophone audio
Technical data
Type HA/200
Power supply (V DC) 12
Max power consumption (mA) 50
Power consumption in stand-by (mA) <35
Storage temperature (°C) -25 to +70
Operating temperature (°C) -15 to +50
IP Rating IP54

Page 7- Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
TARGHA 200
Accessories
HTS
Recessed box
Back-box
Cable gland joints
Spacer
Screws
KHPS
Button
Microcontact
Button spring
KHPD
Buttons
Microcontacts
Button springs
HBP
Wall-mounted base
Blanking plug
Cable gland joint
Joint
Screws and expansion plugs
HPP/6 – HPP/12D
Front plate
Microcontacts with
common call
Lighting group
Cable holders
Blanking plug

521 811 12 14
521 811 12 14
521 811 12 14
521 811 12 14
󱫀󱫂 󱫄
521 811 12 14
521 811 12 14
󱫆󱫈󱫊
󱫌󱫎󱫐
Page 8- Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Recessed installation
The HTS recessed box must be walled in flush with the wall at a suitable height, using the spacer provided in order to avoid any
distortion of the box 󱫀.
In systems where the Larsen eect might occur, the microphone can be mounted remotely 󱫆.
To remove the microphone from its housing, pry it o its base using a small screwdriver, taking care not to damage the
cabling 󱫂.
Before inserting the microphone into the bottom of the back-box, use pliers to remove the part that is highlighted 󱫄.
Insert the audio group high up, near to the top of the back-box 󱫆.
Fit the microcontact (bottom right) into the correct housing 󱫈. The front plate is equipped with a common call for the micro-
contacts, to be used when other buttons are to be installed (maximum of 4) 󱫊.
Insert the lighting group in the relevant housing 󱫌.
Remove the two protective seals on the holes in the recessed box and attach the back-box using the two screws provided 󱫎.
Make the connections and secure the cables using the cable holder 󱫐.
The cable holder must be located near to the audio group.

521 811 12 14
521 811 12 14
521 811 12 14
521 811 12 14
521 811 12 14
󱫀󱫂󱫄
󱫆󱫈 󱫊 󱫌
Page 9- Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Wall mounting
Fix the two blanking plugs to the base 󱫀.
Attach the recessed box (with 3 modules or round Ø 65 mm) flush with the wall and at a suitable height; fix the base to the wall
using the screws and expansion plugs provided 󱫂.
In systems where the Larsen eect might occur, the microphone can be mounted remotely 󱫆.
To remove the microphone from its housing, pry it o its base using a small screwdriver, taking care not to damage the
cabling 󱫄.
Before inserting the microphone into the bottom of the back-box, use pliers to remove the part that is highlighted 󱫆.
Insert the audio group high up, near to the top of the base 󱫆.
Fit the microcontact (bottom right) into the correct housing 󱫈. The front plate is equipped with a common call for the micro-
contacts, to be used when other buttons are to be installed (maximum of 4) 󱫊.
Insert the lighting group in the relevant housing 󱫌.
Make the connections and secure the cables using the cable holder 󱫌.
The cable holder must be located near to the audio group.

521 811 12 14
521 811 12 14
󱫀
󱫀󱫂
󱫀󱫂
Page 10 - Manual FA01423-EN - 03/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Recessing side by side
To recess boxes side by side horizontally or vertically, remove the blanking plugs and insert the cable gland joints 󱫀󱫂.
The recessed boxes must be walled in flush with the wall at a suitable height, using the spacers provided in order to avoid any
distortion of the box 󱫄󱫆.
Button assembly
To write the desired information on the name card, take out the
card holder and the card 󱫀.
Personalised name cards up to a maximum thickness of 2 mm
can be used.
Closing the Front Plate
To assemble the front plate first insert the upper part into the top and then, with a 2.5 hex key, tighten the locking screw 󱫀󱫂.