Cannondale Quick Neo SL w/ Ebikemotion X35 Drive System... Manual

Page 1 of 8
Release : 11/06/19
Technical Supplement (EN)
About Technical Supplements
This document is intended only for competent, experienced bicycle mechanics familiar with bicycle terminology,
service techniques and equipped with proper tools.
This document is not an Owner’s Manual or Owner’s Manual Supplement. These resources can be found as
downloadable Adobe PDFs from our website : www.cannondale.com
WARNING
Information intended for service professionals
only. Improper mechanical work increases the risk
of an accident. Any bicycle accident has risk of
serious injury or death.
If you have any questions about this supplement
please call:
Your Warranty/Technical Representative
MY20 Quick Neo SL, Treadwell Neo
w/ Ebikemotion® X35 Drive System
CONTENTS
Cable Routing Frame Overview............................. 2
Cable Routing Rear Wheel...................................... 3
Bottom Bracket & Cover......................................... 6
Internal Battery Assembly Overview.................... 4
Internal Battery Replacement ............................... 5
Specifications &
Replacement Parts ................................................. 8
Symbols in Use
NGLI-2
- NGLI2 synthetic grease
2
- Loctite® 242 (blue) or equivalent
N·m - Newton meter
OTHER RESOURCES
Ebikemotion® Drive System Manuals
The following internet links will direct you to the
drive manufacturer’s website and a specific user
manual or quick guide you will need to read and
consult:
URL
https://www.ebikemotion.com
http://iWocONEQuick-User-Guide
http://User-Guide-X35-Connection+Mount
http://User-Guide-X35-Care+Maintenance
Periodically, check back with the manufacturers’
website for revisions and/or additions to drive
system manuals.

Page 2 of 8
137379 Rev 1 - Release : 11/06/19
1
3
CP
2
DU
Sen
RD
RB
2
1
3
5 N·m
2
M5
6
7
4
5
8
5 N·m
2
M5
M5 X 12 Max.
7
5
6
4
6
a
b
CC
RD
5
4
5 N·m
2
M5
RB
Technical Supplement Cable Routing
MY20 Quick Neo SL, Treadwell Neo Frame Overview
1. Battery, External (optional)
2. Battery, Internal
3. iWoc® ONE
(drive interface)
4. Water Bottle Mounting Bolts
5. Headtube Plastic Cable Sheet
RB  Rear Brake Line
RD  Rear Derailleur Housing
DU  Drive Unit Cable
FD  Front Derailleur Housing
CP Charge Port Cable
CC - iWoc® ONE Cable
Sen - PAS Sensor Cable
Identification
The DT is an extrusion that
has 2 compartments. The top
compartment is for brake and
RD housing.
All treadwell have rear lights. EQ has front
and rear. Light wire comes out bottom of
battery.

Page 3 of 8
137379 Rev 1 - Release : 11/06/19
Sen
DU
RD
RB
3 N·m
2
M5
1
3
2
3
1
DU
RD
Sen
RB
3 N·m
2
M5
2
3
a
4
4
4
1
1
Secure drive unit cable (DU) to frame
with clips.
Prevent cable from contacting brake
rotor.
1. X35 Drive Unit (rear hub)
2. Cable Clip
3. Bolt
4. Grommet
RB  Rear Brake Line
RD  Rear Derailleur Housing
DU  Drive Unit Cable
FD  Front Derailleur
Housing
Sen - PAS Sensor Cable
Identification
Technical Supplement Cable Routing
MY20 Quick Neo SL, Treadwell Neo Rear Wheel

Page 4 of 8
137379 Rev 1 - Release : 11/06/19
Technical Supplement Internal Battery
MY20 Quick Neo SL, Treadwell Neo Assembly Overview
1
3
CP
2
DU
Sen
RD
RB
2
1
3
5 N·m
2
M5
6
7
4
5
8
5 N·m
2
M5
M5 X 12 Max.
7
5
6
4
6
a
b
CC
RD
5
4
5 N·m
2
M5
RB
NOTICE
Do not use mounting
bolts longer than the
maximum specifed.
Longer bolts will protrude
into the down tube and
damage the internal
battery.
1. Battery, Internal
2. Upper Battery Cables
3. Lower Battery Cables
4. 3M™ Tape
5. Washer, M5
6. Battery Spacer
7. Mounting Bolt
8. Water Bottle
Mounting Bolts
a. Flat side
b. Curved side
Identification

Page 5 of 8
137379 Rev 1 - Release : 11/06/19
Technical Supplement Internal Battery
MY20 Quick Neo SL, Treadwell Neo Replacement Procedure
Remove
1. Disconnect the rear hub and battery connector
on the left chainstay
2. Disassemble the headset cap so that the fork
may be lowered slightly within the headtube.
This is required to enable adequate cable slack.
3. Remove the retaining bolt for the iWoc® ONE
on the top tube and lift up the device. Dis-
connect it from the battery cable.
4. Disconnect any attached optional lighting from
the battery connector.
5. Remove the bottom bracket cover.
6. Remove the screws and lift up the charge port.
Disconnect the device from the battery cable.
7. At the bottom bracket:
Disconnect the wheel sensor, drive unit battery
connectors.
8. Remove the three bolts and washers on the
underside of the downtube to release the
internal battery.
9. Slide the internal battery down and out of the
bottom bracket opening.
10. Remove the three battery spacers from the
battery.
11. There are no servicable parts of the battery. The
removed battery must be handled as electro-
nic waste, subject to regulations regarding
handling or used batteries in your area.
Install
1. Attach the three battery spacers onto the
replacement internal battery at the mounting
points on the lower surface of the battery.
Ax the flat side of the spacers to the battery
over the mounting holes.
2. Insert the upper parts of the battery into the
downtube.
Make sure other cables and housing inside
the downtube are positioned on the top of the
battery inside the downtube.
Align the holes in the battery with the holes in
the frame and install the washers and bolts.
Apply Loctite 242 (blue) to the bolt threads and
tighten to the specified torque.
3. Reconnect the battery to the iWoc® ONE and
charge port and re-install both devices into the
frame. Tighten to the specified torque.
4. At the bottom bracket:
Reconnect the rear hub and battery cable on
the left chainstay.
Reconnect the sensor to the battery.
5. Reinstall the bottom bracket cover and tighten
the cover bolt to the specified torque.
6. Charge the battery.
7. Test the operation of the drive system.

Page 6 of 8
137379 Rev 1 - Release : 11/06/19
Sen
DU
RD
RB
3 N·m
2
M5
1
3
2
3
1
DU
RD
Sen
RB
3 N·m
2
M5
2
3
a
4
4
4
1
1
Technical Supplement Cable Routing
MY20 Quick Neo SL, Treadwell Neo Bottom Bracket & Cover
1. Downtube
2. Bottom Bracket Cover
3. Bolt
4. Cable Tie
RB  Rear Brake Line
RD  Rear Derailleur Housing
DU  Drive Unit Cable
FD  Front Derailleur Housing
Sen - PAS Sensor Cable
a Drain Holes
Identification

Page 7 of 8
137379 Rev 1 - Release : 11/06/19
A
2
3 N·m
M5
1 N·m
2
2 N·m
M3
B
2X
2
3 N·m
M52X
C
H
J
F
L (mm)
G
2
1 N·m
M3
D
K
D
(Blind)
4 mm (2X)
5/4 mm
4/4 mm
5 mm
2
5 N·m
M5
2X
3X
I
Item Specification
Drive System EBike Motion X35 M1-C
Battery EBike Motion X35 B1-C
Drive-Assist Owner's Manual https://www.ebikemotion.com/web/
Head Tube UPR: 11/8in, LWR: 11/4in
Headset Integrated, 11/8in - 11/4in
Bottom Bracket: Type/Width BSA/73mm
Front Derailleur N/A
Seat Post: Dia./Binder 31.6mm/34.9mm
Min. Seat Post Insert 65mm
Item Specification
Tire Size x Max. Tire Width 700c x 42mm
Brakes: Mount Type / Min./Max.
Rotor Dia.
RR: Flat Mount/160mm/160mm,
FT: Flat Mount/140mm/160mm
Axles: Type/Length RR: EBM X35
FR: Maxle TA/ 10012 125mm length
Intended Use ASTM CONDITION 2:
General Purpose Riding
Max. Weight Limit: Total
(Rider+All Equipment) 305lbs/138kg
Frame Size W X L (mm)
SM, S/T 250 x 100
SM 250 x 125
MD, MD S/T 250x150
LG 250x175
ID Part Number Description
AK33050 Derailleur Hanger BT ST SS 077
BK32240 NDS EBM Cable Clips Qty 2
CK34030 Alloy Frame Battery Door
DK32000 Shift/Brake Keyhole Grommets
GK34020 HT Plastic Cable Sheet
HK33080 Dropout Bolts M4x10mm Qty 2
IK76040 X35 Battery/Charge Mounting Hardware
ID Part Number Description
JK34090 DT Light Cable Grommet
KKP312/ Open Oval Grommet x10 (QTY 10)
-- K14040 Herrmans H-Trace E-Bike Rear Light
-- K83038 Ratchet Lever Maxle 100x12 125mm
Technical Supplement Specifications & Replacement Parts
MY20 Quick Neo SL Standard & Remixte Frames

Page 8 of 8
137379 Rev 1 - Release : 11/06/19
Technical Supplement Specifications & Replacement Parts
MY20 Treadwell Neo Standard & Remixte Frames
Item Specification
Drive System EBike Motion X35 M1-C
Battery EBike Motion X35 B1-C
Drive-Assist Owner's Manual https://www.ebikemotion.com/
web/
Head Tube UPR: 11/8in
LWR: 11/8in
Headset Semi-integrated, 1 1/8in -1 1/8in
Bottom Bracket: Type/Width BSA/73mm
Front Derailleur N/A
Seat Post: Dia./Binder 31.6mm/34.9mm
Item Specification
Min. Seat Post Insert 65mm
Tire Size x Max. Tire Width 650b x 48mm
Brakes: Mount Type / Min./Max.
Rotor Dia.
RR: Flat Mount/160mm/160mm,
FT: Flat Mount/140mm/160mm
Axles: Type/Length RR: EBM X35
FR: QR /100  9mm"
Intended Use ASTM CONDITION 2: General
Purpose Riding
Max. Weight Limit: Total
(Rider+All Equipment) 305lbs/138kg
D
(Blind)
4 mm (2X)
5/4 mm
4/4 mm
5 mm
J
L (mm)
2
5 N·m
M5
2X
3X
I
D
2
3 N·m
M5
C
1 N·m
H
K
E
A
2
2 N·m
M3
2X
G
2
1 N·m
M3
B
2
3 N·m
M52X
D
Frame Size W X L (mm)
SM, SM S/T 250X100
MD, MD S/T 250X125
LG 250X150
ID Part Number Description
AK33050 Derailleur Hanger BT ST SS 077
BK32240 NDS EBM Cable Clips (QTY 2)
CK34030 Alloy Frame Battery Door
DK32000 Shift/Brake Keyhole Grommets
EK34000 Treadwell Top Tube Scu Guard
F K32230 Treadwell Neo Bezel
GK34020 HT Plastic Cable Sheet
HK33080 Dropout Bolts M4x10mm (QTY 2)
ID Part Number Description
IK76040 X35 Battery/Charge Mounting Hardware
JK34090 DT Light Cable Grommet
KKP312/ Open Oval Grommet x10 (QTY 10)
-- K13000 Treadwell Front Rack w/ Bamboo Tray
-- K14040 Herrmans H-Trace E-Bike Rear Light
-- K21000 Cruise Control Handlebar 740 x 31.8mm
-- K83038 Ratchet Lever Maxle 100x12 125mm