Canon imageRUNNER ADVANCE 6075 Series User manual
987654321
imageRUNNER ADVANCE 6075 / 6065 / 6055 Series
Service Manual
Revision 5
June 3, 2011
Product Overview
Technology
Periodic Service
Parts Replacement and Clearning
Adjustment
Troubleshooting
Error Code
Service Mode
Installation
Appendix
Application
This manual has been issued by Canon Inc. for qualied persons to learn technical theory,
installation, maintenance, and repair of products. This manual covers all localities where the
products are sold. For this reason, there may be information in this manual that does not
apply to your locality.
Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements
or changes in products. When changes occur in applicable products or in the contents of this
manual, Canon will release technical information as the need arises. In the event of major
changes in the contents of this manual over a long or short period, Canon will issue a new
edition of this manual.
The following paragraph does not apply to any countries where such provisions are
inconsistent with local law.
Trademarks
The product names and company names used in this manual are the registered trademarks
of the individual companies.
Copyright
This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
not be copied, reproduced or translated into another language, in whole or in part, without the
written consent of Canon Inc.
(C) CANON INC. 2011
Caution
Use of this manual should be strictly supervised to avoid disclosure of condential
information.
Explanation of Symbols
The following symbols are used throughout this Service Manual.
Symbols Explanation Symbols Explanation
Check. Remove the claw.
Check visually. Insert the claw.
Check the noise. Use the bundled part.
Disconnect the connector. Push the part.
Connect the connector. Plug the power cable.
Remove the cable/wire
from the cable guide or wire
saddle.
Turn on the power.
Set the cable/wire to the
cable guide or wire saddle.
Remove the screw.
Tighten the screw.
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specic functions and the
relationship between electrical and mechanical systems with reference to the timing of
operation.
In the diagrams, represents the path of mechanical drive; where a signal
name accompanies the symbol, the arrow indicates the direction of the
electric signal.
The expression "turn on the power" means ipping on the power switch, closing the
front door, and closing the delivery unit door, which results in supplying the machine with
power.
2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is
"High", while '0' is used to indicate "Low". (The voltage value, however, differs from
circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked
in the eld. Therefore, the operations of the microprocessors used in the machines
are not discussed: they are explained in terms of from sensors to the input of the DC
controller PCB and from the output of the DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product
improvement or other purposes, and major changes will be communicated in the form of
Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service
Manual and all relevant Service Information bulletins and be able to identify and isolate faults
in the machine.
Blank Page
5
5
Contents
Safety Precautions
CDRH Act -----------------------------------------------------------------------0-2
Laser Safety --------------------------------------------------------------------0-2
Handling of Laser System --------------------------------------------------0-2
Turn power switch ON -------------------------------------------------------0-3
Safety of Toner -----------------------------------------------------------------0-3
About Toner ------------------------------------------------------------------------- 0-3
Toner on Clothing or Skin -------------------------------------------------------- 0-3
Notes When Handling a Lithium Battery --------------------------------0-3
Notes Before it Works Serving ---------------------------------------------0-3
Points to Note at Cleaning --------------------------------------------------0-4
1 Product Overview
Product Lineup -----------------------------------------------------------------1-2
Main Body --------------------------------------------------------------------------- 1-2
Pickup/Delivery System Option ------------------------------------------------ 1-2
Applicable Option for Each Model ------------------------------------------------------ 1-2
Required Options/Conditions ------------------------------------------------------------ 1-3
Scanning System Options ------------------------------------------------------- 1-4
Required Options and Conditions ------------------------------------------------------ 1-4
Function Expansion System Options ----------------------------------------- 1-5
Required Options and Conditions ------------------------------------------------------ 1-5
Features -------------------------------------------------------------------------1-7
Product Features ------------------------------------------------------------------- 1-7
Service Features ------------------------------------------------------------------- 1-7
Improved Service Operability ------------------------------------------------------------ 1-7
New Service Mode ------------------------------------------------------------------------- 1-8
Improved Upgrading Operability -------------------------------------------------------- 1-8
Jam/Error Code Display Specications ----------------------------------------------- 1-9
Applying New Connectors ---------------------------------------------------------------1-10
Specications ---------------------------------------------------------------- 1-11
Product Specications ----------------------------------------------------------- 1-11
Power Supply Specications: --------------------------------------------------1-12
Weight and Size -------------------------------------------------------------------1-12
Productivity (Print Speed) -------------------------------------------------------1-13
Paper Type -------------------------------------------------------------------------1-14
External View/Internal View ---------------------------------------------- 1-25
External View ----------------------------------------------------------------------1-25
External Cover ------------------------------------------------------------------------------1-25
Switches, I/F, Others ----------------------------------------------------------------------1-26
Cross-Section View --------------------------------------------------------------1-26
Operation ---------------------------------------------------------------------- 1-27
Power Switch ----------------------------------------------------------------------1-27
Types of Power Switches ----------------------------------------------------------------1-27
Points to Note on Turning ON/OFF the Power Switch ---------------------------1-27
Control Panel ----------------------------------------------------------------------1-27
Control Panel -------------------------------------------------------------------------------1-27
Main Menu -----------------------------------------------------------------------------------1-28
Differences in Main Menu ---------------------------------------------------------------1-28
Settings/Registration Menu -------------------------------------------------------------1-29
Differences in Settings/Registration Menu ------------------------------------------1-29
2 Technology
Basic Conguration -----------------------------------------------------------2-2
Functional Conguration --------------------------------------------------------- 2-2
Basic Sequence -------------------------------------------------------------------- 2-3
Basic sequence at power ON------------------------------------------------------------ 2-3
Basic sequence at printing <Condition: A4 1-sided (2 sheets), Right deck,
Reverse delivery> -------------------------------------------------------------------------- 2-4
Basic sequence at printing <Condition: A4 2-sided (2 sheets), Right deck,
Reverse delivery> -------------------------------------------------------------------------- 2-5
Main Controller ----------------------------------------------------------------2-6
Overview ----------------------------------------------------------------------------- 2-6
Features --------------------------------------------------------------------------------------- 2-6
Specications/conguration -------------------------------------------------------------- 2-7
6
6
Boot/Shutdown sequence --------------------------------------------------------------- 2-11
Controls -----------------------------------------------------------------------------2-13
Flow of Image Data -----------------------------------------------------------------------2-13
Security features (encryption key and certicate, password protection) -----2-14
High capacity HDD (Option) ------------------------------------------------------------2-23
HDD mirroring feature (option) ---------------------------------------------------------2-24
Removable HDD (option) ----------------------------------------------------------------2-29
HDD Encryption/ Mirroring Kit (optional) ---------------------------------------------2-29
Service Operations ---------------------------------------------------------------2-32
HDD -------------------------------------------------------------------------------------------2-32
Main Controller PCB 1--------------------------------------------------------------------2-33
Main Controller PCB 2--------------------------------------------------------------------2-34
TPM PCB ------------------------------------------------------------------------------------2-36
Laser Exposure System --------------------------------------------------- 2-37
Overview ----------------------------------------------------------------------------2-37
Overview -------------------------------------------------------------------------------------2-37
Specications -------------------------------------------------------------------------------2-38
Parts Conguration ------------------------------------------------------------------------2-38
Controls -----------------------------------------------------------------------------2-39
Overview -------------------------------------------------------------------------------------2-39
Laser ON Timing Control ----------------------------------------------------------------2-39
Laser Beam Intensity Control -----------------------------------------------------------2-41
Polygon Motor Control--------------------------------------------------------------------2-42
Laser Shutter Control ---------------------------------------------------------------------2-42
Servicing ----------------------------------------------------------------------------2-43
Periodically Replaced Parts -------------------------------------------------------------2-43
Consumable Parts -------------------------------------------------------------------------2-43
Periodical Servicing List------------------------------------------------------------------2-43
When Replacing Parts--------------------------------------------------------------------2-43
Major Adjustments -------------------------------------------------------------------------2-43
Image Formation System ------------------------------------------------- 2-44
Overview ----------------------------------------------------------------------------2-44
Overview -------------------------------------------------------------------------------------2-44
Specications -------------------------------------------------------------------------------2-44
Parts Conguration ------------------------------------------------------------------------2-45
Drive Conguration ------------------------------------------------------------------------2-48
Print Process --------------------------------------------------------------------------------2-50
Controls -----------------------------------------------------------------------------2-52
Exposure -------------------------------------------------------------------------------------2-53
Primary Charging --------------------------------------------------------------------------2-54
Developing ----------------------------------------------------------------------------------2-56
Transfer --------------------------------------------------------------------------------------2-58
Separation -----------------------------------------------------------------------------------2-62
Drum Cleaning -----------------------------------------------------------------------------2-64
Drum-related Issues ----------------------------------------------------------------------2-65
Toner Supply Area -------------------------------------------------------------------------2-68
Waste Toner Feeding Area --------------------------------------------------------------2-70
Image Stabilization Control--------------------------------------------------------------2-72
Auxiliary Control ----------------------------------------------------------------------------2-79
Servicing ----------------------------------------------------------------------------2-84
Periodically Replaced Parts -------------------------------------------------------------2-84
Consumable Parts -------------------------------------------------------------------------2-84
Periodical Servicing List------------------------------------------------------------------2-84
When Replacing Parts--------------------------------------------------------------------2-85
Major Adjustments -------------------------------------------------------------------------2-89
Troubleshooting ----------------------------------------------------------------------------2-90
Fixing --------------------------------------------------------------------------- 2-97
Overview ----------------------------------------------------------------------------2-97
Characteristics ------------------------------------------------------------------------------2-97
Specications -------------------------------------------------------------------------------2-98
Parts conguration ------------------------------------------------------------------------2-98
Drive conguration ------------------------------------------------------------------------2-99
Controls --------------------------------------------------------------------------- 2-101
Overview ----------------------------------------------------------------------------------- 2-101
Fixing temperature control------------------------------------------------------------- 2-101
Down sequence control ---------------------------------------------------------------- 2-106
Shutter Control --------------------------------------------------------------------------- 2-108
Paper Anti-wrapping Control ---------------------------------------------------------- 2-109
Thermistor reciprocating control ----------------------------------------------------- 2-110
Upper separation claw reciprocating control -------------------------------------- 2-111
Cleaning web drive control ------------------------------------------------------------ 2-111
Cleaning web length detection ------------------------------------------------------- 2-112
Protective function ----------------------------------------------------------------------- 2-113
Servicing -------------------------------------------------------------------------- 2-114
Periodically Replaced Parts ----------------------------------------------------------- 2-114
Consumable Parts ----------------------------------------------------------------------- 2-114
7
7
Periodical Servicing List---------------------------------------------------------------- 2-114
When Replacing Parts------------------------------------------------------------------ 2-115
Troubleshooting -------------------------------------------------------------------------- 2-116
Pickup / Feed System -----------------------------------------------------2-117
Overview -------------------------------------------------------------------------- 2-117
Overview ----------------------------------------------------------------------------------- 2-117
Specications ----------------------------------------------------------------------------- 2-118
Parts conguration ---------------------------------------------------------------------- 2-119
Drive Conguration ---------------------------------------------------------------------- 2-121
Paper path --------------------------------------------------------------------------------- 2-122
Interval speed ----------------------------------------------------------------------------- 2-123
Various types of control ---------------------------------------------------------------- 2-124
Deck/Cassette Pickup Unit --------------------------------------------------- 2-125
Basic Movement ------------------------------------------------------------------------- 2-125
Deck/Cassette detection --------------------------------------------------------------- 2-126
Paper Size Detection ------------------------------------------------------------------- 2-127
Paper Level Detection ------------------------------------------------------------------ 2-129
Paper Detection -------------------------------------------------------------------------- 2-131
Lifter Control ------------------------------------------------------------------------------ 2-132
Pickup Retry Control -------------------------------------------------------------------- 2-133
Multi-purpose Tray Pickup Unit ---------------------------------------------- 2-134
Basic Movement ------------------------------------------------------------------------- 2-134
Paper Size Detection ------------------------------------------------------------------- 2-135
Paper Detection -------------------------------------------------------------------------- 2-135
Registration Unit ---------------------------------------------------------------- 2-136
Pre-registration Control ---------------------------------------------------------------- 2-136
Registration Control --------------------------------------------------------------------- 2-137
Registration Deceleration Control --------------------------------------------------- 2-137
Registration Acceleration Control ---------------------------------------------------- 2-138
Transfer ---------------------------------------------------------------------------- 2-138
Post-transfer Guide Attraction Control --------------------------------------------- 2-138
Delivery/Reverse Unit ---------------------------------------------------------- 2-139
Basic Operation -------------------------------------------------------------------------- 2-139
Duplex Unit ----------------------------------------------------------------------- 2-141
Basic Operation -------------------------------------------------------------------------- 2-141
Side Registration Control -------------------------------------------------------------- 2-142
Circulation quantity and limit ---------------------------------------------------------- 2-143
Jam Detection ------------------------------------------------------------------- 2-147
Jam Code List ---------------------------------------------------------------------------- 2-147
Forced Paper Feed Control ----------------------------------------------------------- 2-149
Servicing -------------------------------------------------------------------------- 2-150
Periodically Replaced Parts ----------------------------------------------------------- 2-150
Consumable Parts ----------------------------------------------------------------------- 2-150
Periodical Servicing List---------------------------------------------------------------- 2-150
When Replacing Parts------------------------------------------------------------------ 2-150
Major Adjustments ----------------------------------------------------------------------- 2-150
Troubleshooting -------------------------------------------------------------------------- 2-150
External Auxiliary System ----------------------------------------------- 2-151
Overview -------------------------------------------------------------------------- 2-151
Power Supply Conguration ---------------------------------------------------------- 2-151
Controls --------------------------------------------------------------------------- 2-152
Power supply control-------------------------------------------------------------------- 2-152
Fan Control -------------------------------------------------------------------------------- 2-157
Counter control --------------------------------------------------------------------------- 2-158
Servicing -------------------------------------------------------------------------- 2-160
Periodically Replaced Parts ----------------------------------------------------------- 2-160
Consumable Parts ----------------------------------------------------------------------- 2-160
Periodical Servicing --------------------------------------------------------------------- 2-160
When Replacing Parts------------------------------------------------------------------ 2-160
Troubleshooting -------------------------------------------------------------------------- 2-161
MEAP ------------------------------------------------------------------------ 2-163
Changes --------------------------------------------------------------------------- 2-163
Overview ----------------------------------------------------------------------------------- 2-163
SSL Always Enabled -------------------------------------------------------------------- 2-163
Message Display by USB Driver Setting Change ------------------------------- 2-163
Addition of Functions ------------------------------------------------------------------- 2-163
Differences in MEAP Application Data Management when Using New
Functions ---------------------------------------------------------------------------------- 2-164
Addition of SMS Functions ------------------------------------------------------------ 2-164
Authentication Information Sharing Function ------------------------------------- 2-165
Function Supporting Deep Sleep Mode -------------------------------------------- 2-166
Checking the Operating Environment ------------------------------------- 2-166
Outline -------------------------------------------------------------------------------------- 2-166
SMS ----------------------------------------------------------------------------------------- 2-166
SSO-H Management-------------------------------------------------------------------- 2-167
Setting Up the Network -------------------------------------------------------- 2-169
8
8
Network conguration process ------------------------------------------------------- 2-169
Login to SMS --------------------------------------------------------------------- 2-170
Outline -------------------------------------------------------------------------------------- 2-170
Key Pair and Server Certicate when Using Encrypted SSL Communication ---
2-171
Login by Password Authentication -------------------------------------------------- 2-171
Login by RLS Authentication ---------------------------------------------------------- 2-172
Initial Display Languages of SMS --------------------------------------------------- 2-174
Setting the method to login to SMS ---------------------------------------- 2-174
Outline -------------------------------------------------------------------------------------- 2-174
Setting for login by Password Authentication ------------------------------------- 2-175
Setting for login by RLS Authentication -------------------------------------------- 2-176
Checking MEAP Application Management Page ----------------------- 2-177
About MEAP Application Management Page ------------------------------------- 2-177
Starting and Stopping a MEAP Application ------------------------------- 2-178
Procedure to start and stop a MEAP application -------------------------------- 2-178
Checking the Platform Information ----------------------------------------- 2-179
The check procedure of the platform information ------------------------------- 2-179
MEAP Specications ----------------------------------------------------------- 2-179
What is MEAP Specications (MEAP Spec Version)? ------------------------- 2-179
About Name ------------------------------------------------------------------------------- 2-179
Mechanism -------------------------------------------------------------------------------- 2-179
MEAP Application System Information ------------------------------------ 2-181
Outline -------------------------------------------------------------------------------------- 2-181
Checking the System Information of a MEAP Application with SMS ------- 2-181
Printing the System Information of a MEAP Application ----------------------- 2-182
Content of MEAP system information ---------------------------------------------- 2-182
Installing an Application ------------------------------------------------------- 2-183
Resource ----------------------------------------------------------------------------------- 2-183
Procedure to install applications ----------------------------------------------------- 2-184
Adding a License File ---------------------------------------------------------- 2-185
Procedure adding a license le ------------------------------------------------------ 2-185
Disabling a License File ------------------------------------------------------- 2-187
Procedure disabling a license le (suspending a license) --------------------- 2-187
Downloading / Removing an Invalidated License File ----------------- 2-188
Outline -------------------------------------------------------------------------------------- 2-188
Procedure downloading / removing an invalidated license le --------------- 2-188
Reusable license ---------------------------------------------------------------- 2-190
Outline -------------------------------------------------------------------------------------- 2-190
License for forwarding --------------------------------------------------------- 2-190
Outline -------------------------------------------------------------------------------------- 2-190
Procedure to create license for forwarding ---------------------------------------- 2-190
Uninstalling an Application ---------------------------------------------------- 2-193
Procedure to uninstall an application ----------------------------------------------- 2-193
Login Service -------------------------------------------------------------------- 2-194
About Login Service--------------------------------------------------------------------- 2-194
Default Authentication overview------------------------------------------------------ 2-194
SSO-H (Single Sign-On-H) overview ----------------------------------------------- 2-194
Authentication methods of SSO-H -------------------------------------------------- 2-195
Access Mode in Sites ------------------------------------------------------------------- 2-196
Environment conrmation ------------------------------------------------------------- 2-198
Specication of SSO-H ----------------------------------------------------------------- 2-198
Changing Login Services ----------------------------------------------------- 2-199
Steps to Change Login Services ---------------------------------------------------- 2-199
Initializing the Password ------------------------------------------------------ 2-200
Outline -------------------------------------------------------------------------------------- 2-200
Procedure to initialize the SMS login password --------------------------------- 2-200
Backup of the MEAP Application Area and Recovery of the Backup
Data Using SST ----------------------------------------------------------------- 2-200
Outline -------------------------------------------------------------------------------------- 2-200
Backup Item Automatically Copied -------------------------------------------------- 2-201
Requirements for Backup Using the SST ----------------------------------------- 2-201
Procedure for backing up the MEAP application area using SST ----------- 2-202
Procedures to Restore Backup Data ----------------------------------------------- 2-203
Formatting and Replacing the HDD ---------------------------------------- 2-204
Outline -------------------------------------------------------------------------------------- 2-204
Formatting the HDD --------------------------------------------------------------------- 2-204
HDD replacement procedure --------------------------------------------------------- 2-205
MEAP Safe Mode (level 2) --------------------------------------------------- 2-206
Outline -------------------------------------------------------------------------------------- 2-206
Starting in Safe Mode------------------------------------------------------------------- 2-206
How to cancel MEAP SAFE mode -------------------------------------------------- 2-207
Setting HTTP port for MEAP application (level 2) ---------------------- 2-207
Outline -------------------------------------------------------------------------------------- 2-207
Port setup procedure of HTTP Server ---------------------------------------------- 2-208
Port setup procedure of HTTPS Server -------------------------------------------- 2-209
9
9
Using USB Devices ------------------------------------------------------------ 2-210
USB Driver -------------------------------------------------------------------------------- 2-210
Initialization of MEAP driver priority registration --------------------------------- 2-212
USB Device report print ---------------------------------------------------------------- 2-212
Reference material ------------------------------------------------------------- 2-215
Glossary ------------------------------------------------------------------------------------ 2-215
Option for exclusive individual measure ---------------------------------- 2-217
Display Setting of Copy Icon (level2) ----------------------------------------------- 2-217
Error at starting up the MEAP application/Setting to hide JAM screen (level 2) -
2-217
Embedded RDS ----------------------------------------------------------- 2-218
Product Overview --------------------------------------------------------------- 2-218
Overview ----------------------------------------------------------------------------------- 2-218
Features and benets ------------------------------------------------------------------ 2-218
Major Functions -------------------------------------------------------------------------- 2-218
Limitations ------------------------------------------------------------------------ 2-219
Service Mode Menu Transmission Function -------------------------------------- 2-219
Service cautions ----------------------------------------------------------------- 2-219
E-RDS Setup --------------------------------------------------------------------- 2-220
Conrmation and preparation in advance ----------------------------------------- 2-220
E-RDS-related setting items ---------------------------------------------------------- 2-223
Steps to E-RDS settings --------------------------------------------------------------- 2-224
Steps to Service Call button settings ----------------------------------------------- 2-227
Steps to Service Browser settings--------------------------------------------------- 2-229
Initializing E-RDS settings ------------------------------------------------------------- 2-230
FAQ --------------------------------------------------------------------------------- 2-231
Troubleshooting ----------------------------------------------------------------- 2-233
Error code and strings --------------------------------------------------------- 2-236
Updater ---------------------------------------------------------------------- 2-239
Overview -------------------------------------------------------------------------- 2-239
Installing Firmware ------------------------------------------------------------- 2-239
Installing MEAP Application/System Option ------------------------------ 2-240
System Conguration ---------------------------------------------------------- 2-241
List of Functions ----------------------------------------------------------------- 2-242
Distribution Flow ---------------------------------------------------------------- 2-242
Firmware Installation Flow------------------------------------------------------------- 2-242
MEAP Application/System Option Installation Flow ----------------------------- 2-243
Limitations and Cautions ------------------------------------------------------ 2-243
Limitations --------------------------------------------------------------------------------- 2-243
Cautions ------------------------------------------------------------------------------------ 2-243
Overview of Preparation ------------------------------------------------------ 2-245
Setting Sales Company’s HQ ------------------------------------------------ 2-245
Network Settings ---------------------------------------------------------------- 2-246
Connecting to External Network ----------------------------------------------------- 2-246
Conrming URL Setting of Distribution Server ----------------------------------- 2-246
Communication Test -------------------------------------------------------------------- 2-248
Enabling UGW Link ------------------------------------------------------------ 2-249
Enabling [Update Firmware] Button of User Mode --------------------- 2-250
Enabling [Install Application/Options] Button of User Mode ---------- 2-250
Enabling [Manual Update] Button of User Mode (Remote UI) ------ 2-251
System Management Operations ------------------------------------- 2-252
Various Setting ------------------------------------------------------------------ 2-252
Setting URL of Distribution Server -------------------------------------------------- 2-252
Setting Log Level ------------------------------------------------------------------------ 2-253
Displaying Logs ----------------------------------------------------------------- 2-254
Update Logs ------------------------------------------------------------------------------ 2-254
System Logs ------------------------------------------------------------------------------ 2-255
Communication Test ----------------------------------------------------------- 2-257
Upgrading Updater ------------------------------------------------------------- 2-259
Formatting Hard Disk ---------------------------------------------------------- 2-259
How to Replace Controller Boards ----------------------------------------- 2-260
How to Replace Devices ------------------------------------------------------ 2-260
FAQ on Installing Firmware -------------------------------------------------- 2-261
FAQ on Installing MEAP Application/System Option ------------------- 2-262
FAQ on General Matters of Updater --------------------------------------- 2-263
3 Periodic Service
Periodical Service Operation Item ----------------------------------------3-2
4 Parts Replacement and Clearning
List of Parts ---------------------------------------------------------------------4-2
List of External / Internal Cover ------------------------------------------------ 4-2
List of Main Unit -------------------------------------------------------------------- 4-4
10
10
Periodic Replacing Parts,Durable Parts,Cleaning Parts ----------------4-10
Periodic Replacing Parts, Durable Parts --------------------------------------------4-10
List of Cleaning Parts ---------------------------------------------------------------------4-20
List of Fan ---------------------------------------------------------------------------4-34
List of Clutch / Solenoid ---------------------------------------------------------4-36
List of Motor ------------------------------------------------------------------------4-40
List of Sensor ----------------------------------------------------------------------4-46
List of Switch -----------------------------------------------------------------------4-52
List of PCB --------------------------------------------------------------------------4-54
Heater,others -----------------------------------------------------------------------4-58
Connector List ---------------------------------------------------------------------4-60
Main Controller -------------------------------------------------------------- 4-81
Removing Main Controller PCB 1 --------------------------------------------4-81
Removing Main Controller PCB 2 --------------------------------------------4-86
Laser Exposure System --------------------------------------------------- 4-93
Removing the Laser Scanner Unit --------------------------------------------4-93
Cleaning the Dust Collecting Glass ------------------------------------------4-96
Image Formation System ------------------------------------------------- 4-97
Removing the Primary Charging Assembly --------------------------------4-97
Removing the Primary Charging Wire Cleaner, Cleaner Holder (Right/
Left) -----------------------------------------------------------------------------------4-98
Replacing the Primary Charging Assembly Grid Wire ----------------- 4-101
Replacing the Primary Charging Wire ------------------------------------- 4-104
Cleaning the Primary Charging Assembly Grid Wire ------------------ 4-107
Removing the Pre-transfer Charging Assembly ------------------------- 4-108
Removing the Pre-transfer Charging Wire Cleaner, Cleaner Holder ------
4-109
Replacing the Pre-transfer Charging Wire -------------------------------- 4-112
Cleaning the Pre-transfer Charging Wire --------------------------------- 4-114
Removing the Process Unit -------------------------------------------------- 4-114
Cleaning the Process Unit ---------------------------------------------------- 4-116
Removing the Drum Cleaning Unit ----------------------------------------- 4-117
Removing the Drum Cleaning Blade --------------------------------------- 4-118
Cleaning the Drum Cleaning Unit ------------------------------------------- 4-119
Replacing the Pre-exposure Plastic Film --------------------------------- 4-121
Removing the Drum Unit ------------------------------------------------------ 4-121
Removing the Photosensitive Drum ---------------------------------------- 4-122
Cleaning Photosensitive Drum ---------------------------------------------- 4-126
Cleaning the Drum edges ----------------------------------------------------- 4-127
Removing the Cleaner Separation Claw ---------------------------------- 4-127
Removing the Side Seal ------------------------------------------------------ 4-128
Removing the Developing Assembly --------------------------------------- 4-129
Cleaning the Developing Assembly ---------------------------------------- 4-131
Removing the Developing Cylinder and the Developing Roller ----- 4-132
Removing the ETB Unit ------------------------------------------------------- 4-137
Removing the ETB ------------------------------------------------------------- 4-139
Cleaning the ETB --------------------------------------------------------------- 4-140
Removing the Transfer Roller ------------------------------------------------ 4-141
Removing the ETB Cleaning Blade ---------------------------------------- 4-142
Removing the ETB Brush Roller -------------------------------------------- 4-142
Removing the Waste Toner Container ------------------------------------- 4-145
Removing the Drum Heater -------------------------------------------------- 4-146
Removing the Primary Charging Shutter Unit --------------------------- 4-147
Removing the Pre-transfer Charging Assembly Shutter Unit -------- 4-150
Removing the Drum Brush Roller ------------------------------------------- 4-152
Removing the ETB Drive Unit ----------------------------------------------- 4-153
Removing the Transfer Cleaning Unit ------------------------------------- 4-156
Removing the Post-transfer Static Eliminator ---------------------------- 4-156
Removing the Toner Receptacle Tray ------------------------------------- 4-158
Removing the Hopper Unit --------------------------------------------------- 4-159
Removing the Buffer Unit ----------------------------------------------------- 4-163
Removing the Potential Control PCB Unit -------------------------------- 4-166
Removing the Waste Toner Feed Unit ------------------------------------- 4-168
Removing the Drum Drive Unit ---------------------------------------------- 4-171
Removing the Developing Drive Unit -------------------------------------- 4-173
Fixing ------------------------------------------------------------------------- 4-176
Removing the Fixing Assembly ---------------------------------------------- 4-176
Cleaning the Fixing Inlet Guide,Fixing Inlet Sensor Flag, Fixing Right
Stay, Dowel, Dowel Holder --------------------------------------------------- 4-178
Cleaning the Inner Delivery Roller ------------------------------------------ 4-179
Cleaning the Fixing Oil Pan, Fixing Cleaning Web Guide ------------ 4-180
Removing the Fixing Cleaning Web ---------------------------------------- 4-180
11
11
Separating the Fixing Upper Unit from the Fixing Lower Unit ------- 4-182
Removing the Fixing Roller, Insulating Bush and Thrust Stopper -- 4-186
Removing the Pressure Roller ----------------------------------------------- 4-188
Removing the Pressure Roller Static Eliminator Unit ------------------ 4-189
Removing the Main Thermistor, Sub Thermistor2 ---------------------- 4-190
Removing the Sub Thermistor1 --------------------------------------------- 4-192
Removing the Upper Separation Claw ------------------------------------ 4-193
Cleaning the Upper Separation Claw -------------------------------------- 4-194
Removing the Thermoswitch ------------------------------------------------- 4-195
Pickup/Feed System ----------------------------------------------------- 4-197
Removing the Left Pickup Deck --------------------------------------------- 4-197
Removing the Left Deck Pickup Roller ------------------------------------ 4-197
Removing the Left Deck Feed Roller -------------------------------------- 4-198
Removing the Right Pickup Deck ------------------------------------------- 4-198
Removing the Left Deck Separation Roller------------------------------- 4-199
Removing the Right Deck Pickup Roller ---------------------------------- 4-199
Removing the Right Deck Feed Roller ------------------------------------ 4-200
Removing the Right Deck Separation Roller----------------------------- 4-200
Removing the Upper Cassette ---------------------------------------------- 4-201
Removing the Upper Cassette Pickup Roller ---------------------------- 4-201
Removing the Upper Cassette Feed Roller ------------------------------ 4-202
Removing the Upper Cassette Separation Roller ---------------------- 4-202
Removing the Lower Cassette ---------------------------------------------- 4-203
Removing the Lower Cassette Pickup Roller ---------------------------- 4-203
Removing the Lower Cassette Feed Roller ------------------------------ 4-204
Removing the Lower Cassette Separation Roller ---------------------- 4-204
Removing the Multi-purpose Tray Feed Roller -------------------------- 4-205
Removing the Multi-purpose Tray Separation Roller ------------------ 4-206
Cleaning the Pickup and Fixing Feed Assembly ------------------------ 4-207
Removing the Left Deck Pickup Unit --------------------------------------- 4-215
Removing the Right Deck Pickup Unit ------------------------------------- 4-216
Removing the Cassettes 3 and 4 Pickup Unit --------------------------- 4-217
Removing the Vertical Path Cassette Pickup Drive Unit -------------- 4-218
Removing the Registration Unit --------------------------------------------- 4-221
Removing the Left Deck Pickup Drive Unit ------------------------------- 4-224
Removing the Main Drive Unit ----------------------------------------------- 4-225
External Auxiliary System ----------------------------------------------- 4-230
Removing the Filter (for primary charging) ------------------------------- 4-230
Removing the Ozone Filter --------------------------------------------------- 4-230
Removing the DC Controller PCB ------------------------------------------ 4-231
Removing the Power Supply Assembly ----------------------------------- 4-234
Removing the Fixing Power Unit -------------------------------------------- 4-235
Removing the Feed Driver PCB --------------------------------------------- 4-236
Removing the ARCNET PCB ------------------------------------------------ 4-237
Removing the Upper High Voltage Unit ----------------------------------- 4-239
Removing the Flat Control Panel ------------------------------------------- 4-240
5 Adjustment
Overview ------------------------------------------------------------------------5-2
When replacing parts --------------------------------------------------------5-2
Controller System ------------------------------------------------------------------ 5-2
HDD -------------------------------------------------------------------------------------------- 5-2
Main Controller PCB 1--------------------------------------------------------------------- 5-4
Main Controller PCB 2--------------------------------------------------------------------- 5-5
TPM PCB ------------------------------------------------------------------------------------- 5-7
Image Formation System -------------------------------------------------------- 5-7
Primary Charging Wire -------------------------------------------------------------------- 5-7
Primary Charging Assembly ------------------------------------------------------------- 5-7
Pre-transfer Charging Assembly -------------------------------------------------------- 5-9
Pre-transfer Charging Wire--------------------------------------------------------------- 5-9
Photosensitive Drum ----------------------------------------------------------------------5-10
Drum Side Seals (Front and Rear) ---------------------------------------------------- 5-11
Developing Assembly, Developing Cylinder ---------------------------------------- 5-11
Potential Sensor / Potential Control PCB -------------------------------------------- 5-11
ETB Unit / ETB ----------------------------------------------------------------------------- 5-11
Waste Toner Container ------------------------------------------------------------------- 5-11
Fixing System ----------------------------------------------------------------------5-12
Fixing Roller ---------------------------------------------------------------------------------5-12
External Auxiliary System -------------------------------------------------------5-12
DC Controller PCB ------------------------------------------------------------------------5-12
12
12
6 Troubleshooting
Test Print ------------------------------------------------------------------------6-2
Overview ----------------------------------------------------------------------------- 6-2
How to View the Test Print ------------------------------------------------------- 6-3
Grid (TYPE=1) ------------------------------------------------------------------------------- 6-3
17 gradations (TYPE=2/3) ---------------------------------------------------------------- 6-3
Solid white (TYPE=4) ---------------------------------------------------------------------- 6-4
Halftone (TYPE=5/6/11/12/13/14) ------------------------------------------------------ 6-4
Solid black (TYPE=7) ---------------------------------------------------------------------- 6-5
Horizontal line (TYPE=8/9/10) ----------------------------------------------------------- 6-5
Image Faults -------------------------------------------------------------------6-6
Trailing Edge Shock Imaget ----------------------------------------------------- 6-6
Uneven density correction by 2D shading ----------------------------------- 6-7
ADF black line ---------------------------------------------------------------------6-10
Separation Failure Jam due to Deformation of Separation Claw ----- 6-11
Image error due to soil attached to the Cleaning Brushes for the Duplex
Right Roller and the Duplex Outlet Roller ----------------------------------6-12
Uneven density --------------------------------------------------------------------6-18
Smeared image -------------------------------------------------------------------6-19
Adjusting the Edge Emphasis Level -----------------------------------------6-21
MTF Adjustment -------------------------------------------------------------------6-22
Adjustment Procedure --------------------------------------------------------------------6-22
When Making Fine Adjustment After Sampling the MTF Value ----------------6-23
When Disabling the MTF Adjustment -------------------------------------------------6-23
Feed Faults ------------------------------------------------------------------- 6-24
Paper wrinkle ----------------------------------------------------------------------6-24
Other --------------------------------------------------------------------------- 6-24
Adjusting rotation of the Upright Control Panel Arm ---------------------6-24
Remedy to be implemented when the ETB Disengage Member (Transfer
Frame Stopper) is left unremoved --------------------------------------------6-26
Checking nip width ---------------------------------------------------------------6-28
Controller Self Diagnosis -------------------------------------------------- 6-29
Introduction -------------------------------------------------------------------------6-29
Boot System Error Diagnosis Tool ----------------------------------------------------6-29
Controller System Error Diagnosis Tool ---------------------------------------------6-29
Overview ----------------------------------------------------------------------------6-29
Boot System Error Diagnosis Tool -----------------------------------------------------6-29
Controller System Error Diagnosis Tool ----------------------------------------------6-30
Layout Drawing -----------------------------------------------------------------------------6-30
Basic Flowchart -------------------------------------------------------------------6-31
Basic Check Items ------------------------------------------------------------------------6-32
Operation ---------------------------------------------------------------------------6-32
Boot System Error Diagnosis -----------------------------------------------------------6-32
Diagnosis Time ----------------------------------------------------------------------------6-33
Error Diagnosis ----------------------------------------------------------------------------6-34
Controller System Error Diagnosis -------------------------------------------6-34
Boot Method --------------------------------------------------------------------------------6-34
Diagnosis Time ----------------------------------------------------------------------------6-35
Restrictions ----------------------------------------------------------------------------------6-37
Version upgrade ------------------------------------------------------------- 6-38
Overview ----------------------------------------------------------------------------6-38
Overview of Version Upgrade ----------------------------------------------------------6-38
Writing System Software -----------------------------------------------------------------6-39
Download Mode ----------------------------------------------------------------------------6-39
System Software Components ---------------------------------------------------------6-40
Note on Download Process -------------------------------------------------------------6-41
Version Upgrade via SST -------------------------------------------------------6-42
Overview -------------------------------------------------------------------------------------6-42
Copying System Software ---------------------------------------------------------------6-43
Connection ----------------------------------------------------------------------------------6-44
Downloading System Software (Assist mode) -------------------------------------6-46
Downloading System Software (Single mode) -------------------------------------6-47
Formatting HDD ----------------------------------------------------------------------------6-50
Backup ---------------------------------------------------------------------------------------6-54
Version Upgrade using USB memory Storage Device ------------------6-58
Relation between SST and USB memory Storage Device ----------------------6-58
Copying System Software ---------------------------------------------------------------6-59
Connection ----------------------------------------------------------------------------------6-62
Upgrading System Software ------------------------------------------------------------6-63
Downloading/Writing System Software (Automatic) ------------------------------6-65
Downloading System Software (Conrmation) -------------------------------------6-66
Downloading System Software (Overwriting) --------------------------------------6-68
Formatting HDD ----------------------------------------------------------------------------6-69
Backup ---------------------------------------------------------------------------------------6-71
13
13
Clearing Download File ------------------------------------------------------------------6-71
Download Menu 2 -------------------------------------------------------------------------6-71
Other Menu ----------------------------------------------------------------------------------6-71
Troubleshooting -------------------------------------------------------------------6-72
Error Code: E753-0001 ------------------------------------------------------------------6-72
Making Initial Checks ------------------------------------------------------ 6-73
List of Initial Check Items -------------------------------------------------------6-73
Version Upgrade via CDS ------------------------------------------------------6-74
Overview -------------------------------------------------------------------------------------6-74
Preparation -------------------------------------------------------------------------6-74
Overview of Preparation -----------------------------------------------------------------6-74
Setting Sales Company’s HQ -----------------------------------------------------------6-75
Network Settings ---------------------------------------------------------------------------6-75
Enabling UGW Link -----------------------------------------------------------------------6-78
a. UGW-linked Download and Update (Full-remote Update) ----------6-79
b. UGW-linked Download (Remote Distribution Update) ---------------6-79
c. Manual Download and Update (On-site Update from Service Mode) --
6-81
Deleting Firmware Distribution Schedule -----------------------------------6-87
Updating Downloaded Firmware (Applying Firmware) ------------------6-88
Deleting Downloaded Firmware -----------------------------------------------6-89
Troubleshooting on Firmware Installation ----------------------------------6-90
Information required for Reports ----------------------------------------------6-92
Information required for Service Technicians to Obtain on Site ----------------6-92
Information to Report ---------------------------------------------------------------------6-92
Debug Logs ------------------------------------------------------------------------6-93
Obtaining Log Files------------------------------------------------------------------------6-93
Error Messages -------------------------------------------------------------- 6-94
Error Codes ----------------------------------------------------------------- 6-100
How to read an error code ---------------------------------------------------- 6-100
Error Code ------------------------------------------------------------------------ 6-101
Debug log ------------------------------------------------------------------- 6-105
Scope of Application ----------------------------------------------------------- 6-105
Purpose ----------------------------------------------------------------------------------- 6-105
Overview -------------------------------------------------------------------------- 6-105
Function Overview ---------------------------------------------------------------------- 6-105
Storing System Information -------------------------------------------------- 6-105
Storage Method of System Information ------------------------------------------- 6-105
Description of Log to be Collected ------------------------------------------------- 6-105
Collecting System Information ----------------------------------------------- 6-106
Collection Destination ------------------------------------------------------------------ 6-106
Collecting Debug Log (USB memory device) ---------------------------- 6-106
Manual Saving by Holding Down the Counter + 1.2.3 ------------------------- 6-106
DEBUG-1 ------------------------------------------------------------------------- 6-107
Function ----------------------------------------------------------------------------------- 6-107
Uploading Data by SST ------------------------------------------------------- 6-108
Preconditions: ---------------------------------------------------------------------------- 6-108
7 Error Code
Overview ------------------------------------------------------------------------7-2
Outline -------------------------------------------------------------------------------- 7-2
Location code -------------------------------------------------------------------------------- 7-2
Pickup position code ----------------------------------------------------------------------- 7-2
Points to Note When Clearing MN-CON ---------------------------------------------- 7-2
Points to Note When Clearing HDD---------------------------------------------------- 7-2
Error Code ----------------------------------------------------------------------7-3
Error Code Details ----------------------------------------------------------------- 7-3
E000 to E069 -------------------------------------------------------------------------------- 7-3
E100 to E197 -------------------------------------------------------------------------------7-13
E202 to E280 -------------------------------------------------------------------------------7-17
E301 to E355 -------------------------------------------------------------------------------7-20
E400 to E490 -------------------------------------------------------------------------------7-22
E500 to E5F6 -------------------------------------------------------------------------------7-24
E602 ------------------------------------------------------------------------------------------7-34
E604 to E677 -------------------------------------------------------------------------------7-70
E710 to E760 -------------------------------------------------------------------------------7-72
E804 to E996 -------------------------------------------------------------------------------7-78
Jam Code --------------------------------------------------------------------- 7-81
Jam Type ----------------------------------------------------------------------------7-81
Main Unit ----------------------------------------------------------------------------7-82
Duplex Color Image Reader-C1 -----------------------------------------------7-84
Color Image Reader-C1 ---------------------------------------------------------7-85
Paper Deck Unit-D1 --------------------------------------------------------------7-86
Paper Deck Unit-A1 --------------------------------------------------------------7-86
14
14
Inserter-L1 --------------------------------------------------------------------------7-87
PaperFolding Inserter Unit-H1 -------------------------------------------------7-88
External 2-hole Puncher-A1 ----------------------------------------------------7-89
Staple Finisher-E1/Booklet Finisher-E1 -------------------------------------7-90
Alarm Code ------------------------------------------------------------------- 7-91
List of Alarm Code ----------------------------------------------------------------7-91
8 Service Mode
Overview ------------------------------------------------------------------------8-2
Entering Service Mode ----------------------------------------------------------- 8-2
Service Mode Menu --------------------------------------------------------------- 8-2
Service mode item explanations ----------------------------------------------- 8-2
I/O information enhancement --------------------------------------------------- 8-3
Display of Error Code/Alarm Code description ----------------------------- 8-3
COPIER > OPTION > BODY, Item Segmentation ------------------------- 8-4
Security features ------------------------------------------------------------------- 8-5
Related service modes -------------------------------------------------------------------- 8-5
Switching Screen (Level 1 < - > 2) -------------------------------------------- 8-6
Language switch ------------------------------------------------------------------- 8-6
Back-up of service mode --------------------------------------------------------- 8-7
COPIER -------------------------------------------------------------------------8-8
DISPLAY ----------------------------------------------------------------------------- 8-8
VERSION ------------------------------------------------------------------------------------- 8-8
USER -----------------------------------------------------------------------------------------8-30
ACC-STS ------------------------------------------------------------------------------------8-30
ANALOG -------------------------------------------------------------------------------------8-32
CST-STS -------------------------------------------------------------------------------------8-33
HV-STS ---------------------------------------------------------------------------------------8-33
CCD -------------------------------------------------------------------------------------------8-34
DPOT -----------------------------------------------------------------------------------------8-38
SENSOR -------------------------------------------------------------------------------------8-39
MISC ------------------------------------------------------------------------------------------8-39
ENVRNT -------------------------------------------------------------------------------------8-40
2D-SHADE ----------------------------------------------------------------------------------8-40
I/O (I/O display mode) -----------------------------------------------------------8-41
Host Machine_Main Controller (DC-CON>P001 to P005)) ---------------------8-50
Reader (R-CON>P001 to P005) -------------------------------------------------------8-51
ADF (FEEDER>P001 to P007) --------------------------------------------------------8-52
Paper Deck Uint - A1 (SORTER>P048 to P050) ----------------------------------8-53
Paper Deck Uint - D1 (SORTER>P048 to P050) ----------------------------------8-54
Inserter - L1 (SORTER>P047 to P061) ----------------------------------------------8-55
Paper Folding Inserter Unit - H1 (SORTER>P047 to P061) --------------------8-56
External Punch - A1 (SORTER>SORTER>P041 to P046) ---------------------8-58
Staple Finisher - E1 / Booklet Finisher -E1 (SORTER>P001 to P040) ------8-59
ADJUST -----------------------------------------------------------------------------8-64
AE ---------------------------------------------------------------------------------------------8-64
ADJ-XY ---------------------------------------------------------------------------------------8-64
CCD -------------------------------------------------------------------------------------------8-66
LASER ----------------------------------------------------------------------------------------8-77
IMG-REG ------------------------------------------------------------------------------------8-77
DEVELOP -----------------------------------------------------------------------------------8-78
DENS -----------------------------------------------------------------------------------------8-78
BLANK ----------------------------------------------------------------------------------------8-79
V-CONT --------------------------------------------------------------------------------------8-80
PASCAL --------------------------------------------------------------------------------------8-81
HV-PRI ---------------------------------------------------------------------------------------8-81
HV-TR ----------------------------------------------------------------------------------------8-82
FEED-ADJ -----------------------------------------------------------------------------------8-89
CST-ADJ -------------------------------------------------------------------------------------8-93
MISC ------------------------------------------------------------------------------------------8-94
EXP-LED -------------------------------------------------------------------------------------8-97
FUNCTION -------------------------------------------------------------------------8-98
INSTALL --------------------------------------------------------------------------------------8-98
CCD ----------------------------------------------------------------------------------------- 8-100
DPC ----------------------------------------------------------------------------------------- 8-101
CST ----------------------------------------------------------------------------------------- 8-102
CLEANING -------------------------------------------------------------------------------- 8-103
FIXING ------------------------------------------------------------------------------------- 8-103
PANEL -------------------------------------------------------------------------------------- 8-104
PART-CHK -------------------------------------------------------------------------------- 8-104
CLEAR ------------------------------------------------------------------------------------- 8-105
MISC-R ------------------------------------------------------------------------------------- 8-108
MISC-P ------------------------------------------------------------------------------------- 8-112
SENS-ADJ --------------------------------------------------------------------------------- 8-113
SYSTEM ----------------------------------------------------------------------------------- 8-114
15
15
2D-SHADE -------------------------------------------------------------------------------- 8-115
OPTION --------------------------------------------------------------------------- 8-117
FNC-SW ----------------------------------------------------------------------------------- 8-117
DSPLY-SW -------------------------------------------------------------------------------- 8-125
IMG-FIX ------------------------------------------------------------------------------------ 8-128
IMG-DEV ----------------------------------------------------------------------------------- 8-131
IMG-LSR ----------------------------------------------------------------------------------- 8-134
IMG-RDR ---------------------------------------------------------------------------------- 8-134
IMG-MCON -------------------------------------------------------------------------------- 8-136
CLEANING -------------------------------------------------------------------------------- 8-139
ENV-SET ----------------------------------------------------------------------------------- 8-140
FEED-SW ---------------------------------------------------------------------------------- 8-140
NETWORK -------------------------------------------------------------------------------- 8-143
CUSTOM ---------------------------------------------------------------------------------- 8-152
USER --------------------------------------------------------------------------------------- 8-155
CST ----------------------------------------------------------------------------------------- 8-168
ACC ----------------------------------------------------------------------------------------- 8-170
INT-FACE ---------------------------------------------------------------------------------- 8-173
TEMPO ------------------------------------------------------------------------------------- 8-174
LCNS-TR ---------------------------------------------------------------------------------- 8-174
TEST ------------------------------------------------------------------------------- 8-184
PG ------------------------------------------------------------------------------------------- 8-184
NETWORK -------------------------------------------------------------------------------- 8-185
COUNTER ------------------------------------------------------------------------ 8-187
TOTAL -------------------------------------------------------------------------------------- 8-187
PICK-UP ----------------------------------------------------------------------------------- 8-188
FEEDER ----------------------------------------------------------------------------------- 8-188
JAM ----------------------------------------------------------------------------------------- 8-189
MISC ---------------------------------------------------------------------------------------- 8-189
JOB ------------------------------------------------------------------------------------------ 8-190
PRDC-1 ------------------------------------------------------------------------------------ 8-191
DRBL-1 ------------------------------------------------------------------------------------- 8-192
DRBL-2 ------------------------------------------------------------------------------------- 8-197
T-CNTR ------------------------------------------------------------------------------------ 8-201
LF -------------------------------------------------------------------------------------------- 8-201
FEEDER --------------------------------------------------------------------- 8-202
DISPLAY -------------------------------------------------------------------------- 8-202
ADJUST --------------------------------------------------------------------------- 8-203
FUNCTION ----------------------------------------------------------------------- 8-204
OPTION --------------------------------------------------------------------------- 8-206
SORTER -------------------------------------------------------------------- 8-207
ADJUST --------------------------------------------------------------------------- 8-207
FUNCTION ----------------------------------------------------------------------- 8-212
OPTION --------------------------------------------------------------------------- 8-213
BOARD ---------------------------------------------------------------------- 8-215
OPTION --------------------------------------------------------------------------- 8-215
9 Installation
Checking before Installation ------------------------------------------------9-2
Checking Power Supply ---------------------------------------------------------- 9-2
Checking the Installation Environment --------------------------------------- 9-2
Checking Installation Space ----------------------------------------------------- 9-2
Points to Note at Installation Work -------------------------------------------- 9-3
Table of Options Combination ---------------------------------------------9-4
Order to Install the Host machine and the Options ------------------------ 9-4
Checking the Contents ------------------------------------------------------9-5
Unpacking -----------------------------------------------------------------------9-8
Installation -------------------------------------------------------------------- 9-10
Installing the Developing Assembly ------------------------------------------9-10
Installing the Pickup Assembly -----------------------------------------------9-13
Installing the Fixing Assembly -------------------------------------------------9-14
Installing the Toner Container --------------------------------------------------9-16
Installing the Exhaust Filter -----------------------------------------------------9-16
Installing the USB Device Port (only with the products designed for
Europe) -----------------------------------------------------------------------------9-17
Setting the Environment Heater Switch -------------------------------------9-20
Turning ON the Main Power----------------------------------------------------9-21
Turning OFF the Main Power --------------------------------------------------9-21
Toner Stirring -----------------------------------------------------------------------9-22
Installation of the Host Machine -----------------------------------------------9-22
Other Installation Work ----------------------------------------------------------9-22
Setting the Deck -------------------------------------------------------------------9-23
Setting the Paper Cassette -----------------------------------------------------9-25
Auto Adjust Gradation -----------------------------------------------------------9-26
16
16
Image Position Adjustment -----------------------------------------------------9-26
Left Edge Margin Adjustment (1st side) ----------------------------------------------9-26
Left Edge Margin Adjustment (2nd side) ---------------------------------------------9-28
Leading Edge Margin Adjustment (1st side) ----------------------------------------9-29
Leading Edge Margin Adjustment (2nd side) ---------------------------------------9-29
Adjusting margin of Multi-purpose Pickup Tray ------------------------------------9-30
Leading Edge Margin Adjustment (Multi-purpose Tray Pickup) ----------------9-31
Checking the Network Connection -------------------------------------------9-31
Overview -------------------------------------------------------------------------------------9-31
Checking the Network Connection ----------------------------------------------------9-31
Operation Procedure Using Ping ------------------------------------------------------9-32
Checking by the Remote Host Address ----------------------------------------------9-32
Network Troubleshooting -------------------------------------------------------9-32
Checking Connection of the Network Cable ----------------------------------------9-32
Operation Procedure Using Ping ------------------------------------------------------9-32
Checking the Network Setting of the Host Machine----------------------9-33
Checking Network Function on the Main Controller----------------------9-33
When Relocating the Machine ------------------------------------------- 9-34
Printer Cover -B1 ------------------------------------------------------------ 9-37
Points to Note at Installation ---------------------------------------------------9-37
Checking the Contents ---------------------------------------------------------9-37
Check Items when Turning OFF the Main Power-------------------------9-38
Installation Procedure ------------------------------------------------------------9-38
Operation Check ------------------------------------------------------------------9-41
Shift Tray-E1 ----------------------------------------------------------------- 9-42
Checking the Contents ----------------------------------------------------------9-42
Checking before Installation ----------------------------------------------------9-43
Installation Procedure ------------------------------------------------------------9-43
Reader Heater Unit --------------------------------------------------------- 9-48
Checking the Contents (ASIA only) ------------------------------------------9-48
Reader Heater Unit-G1-------------------------------------------------------------------9-48
Checking the Parts to be Installed (Europe only) -------------------------9-48
Reader Heater Unit------------------------------------------------------------------------9-48
Check Items when Turning OFF the Main Power-------------------------9-48
Installation Procedure ------------------------------------------------------------9-49
Cassette Heater Unit ------------------------------------------------------- 9-54
Checking the Contents (Asia only) -------------------------------------------9-54
Cassette Heater Unit-38 -----------------------------------------------------------------9-54
Checking the Parts to be Installed (Europe only) -------------------------9-54
Check Items when Turning OFF the Main Power ------------------------9-54
Installation Procedure ------------------------------------------------------------9-54
Paper Deck Heater Unit-A1 ---------------------------------------------- 9-58
Checking the Contents ----------------------------------------------------------9-58
Check Items when Turning OFF the Main Power-------------------------9-59
Installation Procedure (Paper Deck Unit-A1) ------------------------------9-59
Installation Procedure (Paper Deck Unit-D1) ------------------------------9-67
Utility Tray-A1/A2 ------------------------------------------------------------ 9-75
Checking the Contents ----------------------------------------------------------9-75
Installation Procedure ------------------------------------------------------------9-76
When Installing the USB Keyboard ------------------------------------------9-77
Card Reader-C1/Copy Card Reader-F1 ------------------------------ 9-78
Points to Note at Installation ---------------------------------------------------9-78
Checking the Contents ----------------------------------------------------------9-78
Contents of Card Reader-C1 -----------------------------------------------------------9-78
Contents of Copy Card Reader Attachment-A2 ------------------------------------9-79
Check Items when Turning OFF the Main Power ------------------------9-80
Installation Procedure ------------------------------------------------------------9-80
Setting After Installation ---------------------------------------------------------9-87
Voice Guidance Kit-F1/F2 ------------------------------------------------- 9-88
Points to Note at Installation ---------------------------------------------------9-88
Checking the Contents ----------------------------------------------------------9-88
Check Items when Turning OFF the Main Power-------------------------9-89
Installation Procedure ------------------------------------------------------------9-89
Checking after Installation ------------------------------------------------------9-93
Operation Check ------------------------------------------------------------------9-93
Installation Procedure for Expansion Bus-F1/F2, IPSec Board-B2
and Wireless LAN Board-B1 --------------------------------------------- 9-94
Points to Note at Installation ---------------------------------------------------9-94
Checking the Contents ----------------------------------------------------------9-95
Expansion Bus-F1/F2---------------------------------------------------------------------9-95
IPSec Board-B2 ----------------------------------------------------------------------------9-95
Wireless LAN Board-B1 ------------------------------------------------------------------9-96
Check Items when Turning OFF the Main Power-------------------------9-97
17
17
Installation Procedure ------------------------------------------------------------9-98
Removing the Main Controller PCB 1 ------------------------------------------------9-98
Installing the Expansion Bus-F1/F2 and the IPSec Board-B2 Simultaneously --
9-99
Installing the Expansion Bus-F1/F2, the Wireless LAN Board-B1 and the
IPSec Board-B2 Simultaneously ----------------------------------------------------- 9-100
Checking after Installation ---------------------------------------------------- 9-105
Additional Memory Type B (512MB) --------------------------------- 9-106
Checking the Contents -------------------------------------------------------- 9-106
Checking before Installation -------------------------------------------------- 9-106
Check Items when Turning OFF the Main Power ---------------------- 9-106
Installation Procedure ---------------------------------------------------------- 9-106
Checking after Installation ---------------------------------------------------- 9-107
Description on the parts included in the package ----------------- 9-108
Combination of HDD Options ------------------------------------------ 9-108
[TYPE-1] Option HDD (250GB) --------------------------------------- 9-109
Checking the Contents -------------------------------------------------------- 9-109
Points to Note Regarding Data Backup/Export-------------------------- 9-110
Making a Backup of the Data (Reference only) --------------------------9-111
Check Items when Turning OFF the Main Power----------------------- 9-115
Assembling the Option HDD ------------------------------------------------- 9-115
Procedure to Replace with the HDD --------------------------------------- 9-116
Installing the System Software Using the SST -------------------------- 9-118
Execution of Auto Gradation Adjustment---------------------------------- 9-118
[TYPE-2] Removable HDD Kit ------------------------------------------9-119
Checking the Contents -------------------------------------------------------- 9-119
Check Items when Turning OFF the Main Power----------------------- 9-120
Installation Procedure ---------------------------------------------------------- 9-120
Removing the HDD and HDD Case Unit ------------------------------------------ 9-120
Disassembling and Assembling of the HDD Removed from the Host Machine -
9-123
Changing Conguration inside of HDD Case Unit ------------------------------ 9-126
Installing the HDD Case Unit --------------------------------------------------------- 9-127
[TYPE-3] Option HDD (250GB) + Removable HDD Kit --------- 9-130
Checking the Contents -------------------------------------------------------- 9-130
Option HDD (250GB) ------------------------------------------------------------------- 9-130
Removable HDD Kit--------------------------------------------------------------------- 9-131
Points to Note Regarding Data Backup/Export-------------------------- 9-132
Making a Backup of the Data (Reference only) ------------------------- 9-133
Check Items when Turning OFF the Main Power----------------------- 9-137
Installation Procedure ---------------------------------------------------------- 9-137
Assembling the Option HDD ---------------------------------------------------------- 9-137
Removing the HDD and HDD Case Unit ------------------------------------------ 9-140
Changing Conguration inside of HDD Case Unit ------------------------------ 9-142
Installing the HDD Case Unit --------------------------------------------------------- 9-144
Installing the System Software Using the SST -------------------------- 9-147
Execution of Auto Gradation Adjustment---------------------------------- 9-147
[TYPE-4] Option HDD (80GB) + HDD Mirroring Kit or HDD Data
Encryption & Mirroring Kit ----------------------------------------------- 9-148
Points to Note when Unpacking HDD Data Encryption & Mirroring Kit ---
9-148
Checking the Contents -------------------------------------------------------- 9-148
Option HDD (80GB) --------------------------------------------------------------------- 9-149
HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit ------------------- 9-150
Points to Note when HDD Data Encryption & Mirroring Kit has been
Installed --------------------------------------------------------------------------- 9-151
Points to Note Regarding Data Backup/Export ---------------------------------- 9-151
Making a Backup of the Data (Reference only) ---------------------------------- 9-152
Check Items when Turning OFF the Main Power----------------------- 9-156
Installation Procedure ---------------------------------------------------------- 9-156
Removing the Covers------------------------------------------------------------------- 9-156
Installing the Mirroring Board or Encryption Board ------------------------------ 9-158
After Installing HDD Data Encryption & Mirroring Kit ------------------ 9-168
Installing the System Software Using the SST ----------------------------------- 9-168
Checking the Security Version ------------------------------------------------------- 9-168
Checking the Security Mark ----------------------------------------------------------- 9-168
Setting for Mirroring ------------------------------------------------------------ 9-169
After Installing HDD Data Encryption & Mirroring Kit ------------------ 9-169
Reporting to the System Administrator at the End of the Work -------------- 9-169
Execution of Auto Gradation Adjustment ------------------------------------------ 9-169
[TYPE-5] 2 Option HDDs (250GB) + HDD Mirroring Kit or HDD
Data Encryption & Mirroring Kit ---------------------------------------- 9-170
Points to Note when Unpacking HDD Data Encryption & Mirroring Kit ---
9-170
18
18
Checking the Contents -------------------------------------------------------- 9-170
Option HDD (250GB) ------------------------------------------------------------------- 9-171
HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit ------------------- 9-172
Points to Note when HDD Data Encryption & Mirroring Kit has been
Installed --------------------------------------------------------------------------- 9-173
Points to Note Regarding Data Backup/Export ---------------------------------- 9-173
Making a Backup of the Data (Reference only) ---------------------------------- 9-174
Check Items when Turning OFF the Main Power----------------------- 9-178
Installation Procedure ---------------------------------------------------------- 9-178
Assembling the Option HDD ---------------------------------------------------------- 9-178
Removing the Covers------------------------------------------------------------------- 9-179
Installing the Mirroring Board or Encryption Board ------------------------------ 9-181
Installing the System Software Using the SST -------------------------- 9-190
After Installing HDD Data Encryption & Mirroring Kit ------------------ 9-190
Checking the Security Version ------------------------------------------------------- 9-190
Checking the Security Mark ----------------------------------------------------------- 9-190
Setting for Mirroring ------------------------------------------------------------ 9-191
Reporting to the System Administrator at the End of the Work (only
when HDD Data Encryption & Mirroring Kit has been installed) ---- 9-191
Execution of Auto Gradation Adjustment---------------------------------- 9-191
[TYPE-6] HDD Data Encryption & Mirroring Kit ------------------- 9-192
Points to Note when HDD Data Encryption & Mirroring Kit has been
Installed --------------------------------------------------------------------------- 9-192
Checking the Contents -------------------------------------------------------- 9-192
Points to Note Regarding Data Backup/Export-------------------------- 9-193
Making a Backup of the Data (Reference only) ------------------------- 9-194
Check Items when Turning OFF the Main Power----------------------- 9-198
Installation Procedure ---------------------------------------------------------- 9-198
Removing the Covers------------------------------------------------------------------- 9-198
Installing the Encryption Board ---------------------------------------------- 9-199
Installing the System Software Using the SST -------------------------- 9-207
Checking the Security Version ----------------------------------------------- 9-207
Checking the Security Mark -------------------------------------------------- 9-207
Checking after Installation ---------------------------------------------------- 9-208
Reporting to the System Administrator at the End of the Work ----- 9-208
Execution of Auto Gradation Adjustment---------------------------------- 9-208
[TYPE-7] Option HDD (250GB) + HDD Data Encryption & Mirroring
Kit ----------------------------------------------------------------------------- 9-209
Points to Note when Unpacking HDD Data Encryption & Mirroring Kit ---
9-209
Checking the Contents -------------------------------------------------------- 9-209
Option HDD (250GB) ------------------------------------------------------------------- 9-210
HDD Data Encryption & Mirroring Kit ----------------------------------------------- 9-211
Points to Note Regarding Data Backup/Export-------------------------- 9-212
Making a Backup of the Data (Reference only) ------------------------- 9-213
Check Items when Turning OFF the Main Power----------------------- 9-217
Installation Procedure ---------------------------------------------------------- 9-217
Assembling the Option HDD ---------------------------------------------------------- 9-217
Removing the Covers------------------------------------------------------------------- 9-218
Installing the Encryption Board ---------------------------------------------- 9-220
Installing the System Software Using the SST -------------------------- 9-228
Checking the Security Version ----------------------------------------------- 9-228
Checking the Security Mark -------------------------------------------------- 9-228
Checking after Installation ---------------------------------------------------- 9-229
Reporting to the System Administrator at the End of the Work ----- 9-229
Execution of Auto Gradation Adjustment---------------------------------- 9-229
[TYPE-8] Option HDD (80GB) + Removable HDD Kit + HDD
Mirroring Kit or HDD Data Encryption & Mirroring Kit ------------ 9-230
Points to Note when Unpacking HDD Data Encryption & Mirroring Kit ---
9-230
Checking the Contents -------------------------------------------------------- 9-230
Option HDD (80GB) --------------------------------------------------------------------- 9-231
Removable HDD Kit--------------------------------------------------------------------- 9-232
HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit ------------------- 9-233
Points to Note when HDD Data Encryption & Mirroring Kit has been
Installed --------------------------------------------------------------------------- 9-234
Points to Note Regarding Data Backup/Export ---------------------------------- 9-234
Making a Backup of the Data (Reference only) ---------------------------------- 9-235
Check Items when Turning OFF the Main Power----------------------- 9-239
Installation Procedure ---------------------------------------------------------- 9-239
Removing the HDD and HDD Case Unit ------------------------------------------ 9-239
Disassembling and Assembling of the HDD Removed from the Host Machine
(the First HDD) --------------------------------------------------------------------------- 9-242
19
19
Assembling the Option HDD (the Second HDD) -------------------------------- 9-245
Changing Conguration inside of HDD Case Unit ------------------------------ 9-248
Installing the Mirroring Board or Encryption Board and HDD Case Unit -- 9-249
After Installing HDD Data Encryption & Mirroring Kit ------------------ 9-256
Installing the System Software Using the SST ----------------------------------- 9-256
Checking the Security Version ------------------------------------------------------- 9-256
Checking the Security Mark ----------------------------------------------------------- 9-256
Setting for Mirroring ------------------------------------------------------------ 9-257
After Installing HDD Data Encryption & Mirroring Kit ------------------ 9-257
Reporting to the System Administrator at the End of the Work -------------- 9-257
Execution of Auto Gradation Adjustment ------------------------------------------ 9-257
[TYPE-9] 2 Option HDDs (250GB) + Removable HDD Kit + HDD
Mirroring Kit or HDD Data Encryption & Mirroring Kit ------------ 9-259
Points to Note when HDD Data Encryption & Mirroring Kit has been
Installed --------------------------------------------------------------------------- 9-259
Checking the Contents -------------------------------------------------------- 9-259
Option HDD (250GB) ------------------------------------------------------------------- 9-260
Removable HDD Kit--------------------------------------------------------------------- 9-261
HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit ------------------- 9-262
Points to Note when HDD Data Encryption & Mirroring Kit has been
Installed --------------------------------------------------------------------------- 9-263
Points to Note Regarding Data Backup/Export ---------------------------------- 9-263
Making a Backup of the Data (Reference only) ---------------------------------- 9-264
Check Items when Turning OFF the Main Power----------------------- 9-268
Installation Procedure ---------------------------------------------------------- 9-268
Assembling the Option HDD ---------------------------------------------------------- 9-268
Removing the HDD and HDD Case Unit ------------------------------------------ 9-271
Changing Conguration inside of HDD Case Unit ------------------------------ 9-274
Installing the Mirroring Board or Encryption Board and HDD Case Unit -- 9-275
Installing the System Software Using the SST -------------------------- 9-282
After Installing HDD Data Encryption & Mirroring Kit ------------------ 9-282
Checking the Security Version ------------------------------------------------------- 9-282
Checking the Security Mark ----------------------------------------------------------- 9-282
Setting for Mirroring ------------------------------------------------------------ 9-283
Reporting to the System Administrator at the End of the Work (Only
When HDD Data Encryption & Mirroring Kit has been Installed) --- 9-283
Execution of Auto Gradation Adjustment---------------------------------- 9-283
[TYPE-10] Removable HDD Kit + HDD Data Encryption & Mirroring
Kit ----------------------------------------------------------------------------- 9-285
Points to Note when Unpacking HDD Data Encryption & Mirroring Kit ---
9-285
Checking the Contents -------------------------------------------------------- 9-285
Removable HDD Kit--------------------------------------------------------------------- 9-285
HDD Data Encryption & Mirroring Kit ----------------------------------------------- 9-286
Points to Note Regarding Data Backup/Export-------------------------- 9-287
Making a Backup of the Data (Reference only) ------------------------- 9-288
Check Items when Turning OFF the Main Power----------------------- 9-292
Installation Procedure ---------------------------------------------------------- 9-292
Removing the HDD and HDD Case Unit ------------------------------------------ 9-292
Disassembling and Assembling of the HDD Removed from the Host Machine -
9-295
Changing Conguration inside of HDD Case Unit ------------------------------ 9-298
Installing the Encryption Board and HDD Case Unit --------------------------- 9-299
Installing the System Software Using the SST -------------------------- 9-306
Checking the Security Version ----------------------------------------------- 9-306
Checking the Security Mark -------------------------------------------------- 9-306
Checking after Installation ---------------------------------------------------- 9-307
Reporting to the System Administrator at the End of the Work ----- 9-307
Execution of Auto Gradation Adjustment---------------------------------- 9-307
[TYPE-11] Option HDD (250GB) + Removable HDD Kit + HDD
Data Encryption & Mirroring Kit ---------------------------------------- 9-309
Points to Note when Unpacking HDD Data Encryption & Mirroring Kit ---
9-309
Checking the Contents -------------------------------------------------------- 9-309
Option HDD (250GB) ------------------------------------------------------------------- 9-310
Removable HDD Kit--------------------------------------------------------------------- 9-311
HDD Data Encryption & Mirroring Kit ----------------------------------------------- 9-312
Points to Note Regarding Data Backup/Export-------------------------- 9-313
Making a Backup of the Data (Reference only) ------------------------- 9-314
Check Items when Turning OFF the Main Power----------------------- 9-318
Installation Procedure ---------------------------------------------------------- 9-318
Assembling the Option HDD ---------------------------------------------------------- 9-318
Removing the HDD and HDD Case Unit ------------------------------------------ 9-320
Changing Conguration inside of HDD Case Unit ------------------------------ 9-323
20
20
Installing the Encryption Board and HDD Case Unit --------------------------- 9-324
Installing the System Software Using the SST -------------------------- 9-331
Checking the Security Version ----------------------------------------------- 9-331
Checking the Security Mark -------------------------------------------------- 9-331
Checking after Installation ---------------------------------------------------- 9-332
Reporting to the System Administrator at the End of the Work ----- 9-332
Execution of Auto Gradation Adjustment---------------------------------- 9-332
Appendix
Service Tools --------------------------------------------------------------------- II
Special Tools --------------------------------------------------------------------------- II
Solvents and Oils ---------------------------------------------------------------------V
General Timing Chart --------------------------------------------------------- VI
Basic sequence at power ON ----------------------------------------------------- VI
Basic sequence at printing <Condition: A4 1-sided (2 sheets), Right
deck, Reverse delivery> ---------------------------------------------------------- VII
Basic sequence at printing <Condition: A4 2-sided (2 sheets), Right
deck, Reverse delivery> --------------------------------------------------------- VIII
General Circuit Diagram ------------------------------------------------------ IX
Signal Input/Output List ------------------------------------------------------------ IX
General Circuit Diagram ---------------------------------------------------------- XII
General Circuit Diagram (1/24)----------------------------------------------------------- XII
General Circuit Diagram (2/24)---------------------------------------------------------- XIII
General Circuit Diagram (3/24)----------------------------------------------------------XIV
General Circuit Diagram (4/24)-----------------------------------------------------------XV
General Circuit Diagram (5/24)----------------------------------------------------------XVI
General Circuit Diagram (6/24)--------------------------------------------------------- XVII
General Circuit Diagram (7/24)-------------------------------------------------------- XVIII
General Circuit Diagram (8/24)----------------------------------------------------------XIX
General Circuit Diagram (9/24)-----------------------------------------------------------XX
General Circuit Diagram (10/24) --------------------------------------------------------XXI
General Circuit Diagram (11/24) ------------------------------------------------------- XXII
General Circuit Diagram (12/24) ------------------------------------------------------ XXIII
General Circuit Diagram (13/24) ------------------------------------------------------XXIV
General Circuit Diagram (14/24) -------------------------------------------------------XXV
General Circuit Diagram (15/24) ------------------------------------------------------XXVI
General Circuit Diagram (16/24) ----------------------------------------------------- XXVII
General Circuit Diagram (17/24) ---------------------------------------------------- XXVIII
General Circuit Diagram (18/24) ------------------------------------------------------XXIX
General Circuit Diagram (19/24) -------------------------------------------------------XXX
General Circuit Diagram (20/24) ------------------------------------------------------XXXI
General Circuit Diagram (21/24) ----------------------------------------------------- XXXII
General Circuit Diagram (22/24) ---------------------------------------------------- XXXIII
General Circuit Diagram (23/24) ----------------------------------------------------XXXIV
General Circuit Diagram (24/24) -----------------------------------------------------XXXV
List of User Mode -------------------------------------------------------- XXXVI
Device Information Delivery Settings ------------------------------------- XXXVI
Environment Settings -------------------------------------------------------- XXXVII
Paper Settings -------------------------------------------------------------------------- XXXVII
Display Settings ----------------------------------------------------------------------- XXXVIII
Timer/Energy Settings -----------------------------------------------------------------XXXIX
Network ---------------------------------------------------------------------------------------- XL
External Interface ------------------------------------------------------------------------- XLVI
Accessibility -------------------------------------------------------------------------------- XLVI
Adjustment/Maintenance -------------------------------------------------------XLVII
Adjust Image Quality*1 -------------------------------------------------------------------XLVII
Adjust Action*1 -----------------------------------------------------------------------------XLVII
Maintenance -------------------------------------------------------------------------------XLVII
Function Settings ---------------------------------------------------------------XLVIII
Common -----------------------------------------------------------------------------------XLVIII
Copy*1 -------------------------------------------------------------------------------------------- LI
Printer -------------------------------------------------------------------------------------------- LI
Send -------------------------------------------------------------------------------------------- LII
Receive/Forward --------------------------------------------------------------------------- LVI
Store/Access Files --------------------------------------------------------------------------LVII
Encrypted Secure Print-------------------------------------------------------------------LVIII
Set Destination --------------------------------------------------------------------- LIX
Set Destination ----------------------------------------------------------------------------- LIX
Management Settings ------------------------------------------------------------- LX
User Management --------------------------------------------------------------------------- LX
Device Management ------------------------------------------------------------------------ LX
License/Other ------------------------------------------------------------------------------- LXII
Data Management -------------------------------------------------------------------------LXIII
Backup Data ------------------------------------------------------------------LXIV
Detail of HDD partition ---------------------------------------------------LXVIII
This manual suits for next models
2
Table of contents
Other Canon All In One Printer manuals
Canon
Canon PIXMA MG5520 User manual
Canon
Canon MultiPASS F30 User manual
Canon
Canon ImageRunner iR8500 Series User manual
Canon
Canon iP6700D - PIXMA Color Inkjet Printer User manual
Canon
Canon 2711B019AB Assembly instructions
Canon
Canon MultiPASS F80 Manual
Canon
Canon MX720 Series Setup guide
Canon
Canon ImageCLASS D420 User manual
Canon
Canon Color imageCLASS MF8050Cn Safety guide
Canon
Canon imageRUNNER ADVANCE 8105 User manual
Canon
Canon imageCLASS D780 Installation and maintenance instructions
Canon
Canon PIXMA MX870 Series User manual
Canon
Canon LASERBASE MF5700 Series User manual
Canon
Canon imageRUNNER 1435iF+ User manual
Canon
Canon imageRunner 400 User manual
Canon
Canon MB5000 Series Setup guide
Canon
Canon imageRUNNER 2230 User manual
Canon
Canon MultiPASS L60 Safety guide
Canon
Canon imageRunner 2220i User manual
Canon
Canon MB5100 Series Setup guide
