Canon imageRUNNER ADVANCE C2030 User manual

2
2
How to Check this Installation Procedure
When using the parts included in the package
A symbol is described on the illustration in the case of using the parts included in the package
of this product.
Packaged Item
Symbols in the illustration
The frequently-performed operations are described with symbols in this procedure.
Connector
Disconnect
Screw
Tighten Remove Connect Secure Free
Harness
Push
Insert Plug in Turn on
Sound CheckCheck Visual Check
Claw
Remove
Checking instruction
F-1-1
F-1-2
Checking the Contents
[1] Cassette Pedestal X 1 [2] Connecting Fixture X 1
[3] Screw (RS Tightening; M3X8.5) X 1 [4] Size Plate X 2
[5] Connector Cover X 1
< CD/Guides >
• FCC/IC Sheet (Only for USA and Europe)
F-1-3

3
3
Checking the Contents
Although pictures and illustrations of imageRUNNER ADVANCE C2030/C2020 Series are
used in this procedure, the procedure is the same in the case of models other than the series.
Installation Outline Drawing
Check Item when Turning OFF the Main Power
Chek that the main power switch is OFF
1) Turn OFF the main power switch of the host machine.
2) Be sure that Control Panel Display and the Main Power lamp are both turned OFF, and
then disconnect the power plug.
F-1-4
Unpacking
1) Turn OFF the main power switch of the host machine.
2) Open the plastics, and remove the 2 pads by lifting the rear of the equipment. Then, tuck
the plastics toward the front.
Plastic
Pad
Pad
F-1-5
F-1-6

4
4
3) Remove the remaining 2 pads and plastics by lifting the front of the equipment.
Plastic Pad
Pad
4) Lift the equipment down from pallet.
5) Remove all tapes attached to the equipment and packing materials from the equipment.
CAUTION:
Be sure to remove tapes on the rear side of the host machine after completing the
installation of the equipment; otherwise, cables may be trapped.
F-1-7
F-1-8
Installation Procedure
1) Open the Right Lower Cover.
CAUTION:
If mounting the host machine without opening the Right Lower Cover, the cover may get
damage.
2) If the Right Lower Sub Cover is installed to the host machine, remove it using a at-blade
screwdriver.
NOTE:
When installing the host machine at the same time, skip this step because the Right
Lower Sub Cover is packed with the host machine.
F-1-9
F-1-10

5
5
3) Mount the host machine by aligning the corners (right and left) of the front side of the host
machine with the corners (right and left) of the front side of the equipment.
CAUTION:
When mounting the host machine to the equipment, be sure to move the host machine
parallel and t the 2 Positioning Pins on top of the equipment into the holes on the Base
Plate of the host machine.
Positioning Pins
F-1-11
CAUTION:
• Be sure to perform the work in accordance with the standard to handle a heavy load
in each country.
• [imageRUNNER ADVANCE C2030/C2020 Series] the maximum weight of the
machine: 95kg (the host machine with 2 cassettes + ADF)
• [imageRUNNER ADVANCE C2030/C2020 Series [imageRUNNER ADVANCE
C2030/C2020 Series] the maximum weight of the machine: 75.4kg (the model
with FAX)
• Be sure to keep the machine leveled when lifting it.
• Because the center of gravity will be placed at rear, be careful not to lose balance
when lifting it.
F-1-12

6
6
4) Press the cassette release button, and remove the Cassettes 2 and 3.
Button
5) Attach the Connecting Fixture.
• 1 Screw (RS Tightening; M3x8.5)
• 1 Boss
CAUTION:
When attaching the Connecting Fixture, be sure the attaching direction
.
imageRUNNER ADVANCE
C2030/C2020 Series
Models other than
imageRUNNER ADVANCE
C2030/C2020 Series
F-1-14
F-1-13
[imageRUNNER ADVANCE C2030/2025/C2020 Series]
F-1-15

7
7
[Models other than imageRUNNER ADVANCE C2030/C2020 Series]
NOTE:
Hook the [A] part of the Connecting Fixture on the plate [B] on the host machine side,
aligning with the boss at installation.
[A] [B]
6) Install the Cassette 2 and 3.
7) Close the Cassette Right Lower Cover.
F-1-16
8) Remove the Connector Cover of the host machine. (The removed Connector Cover will not
be used.)
• 1 W Sems Screw (The removed screw will be used in step 11.)
NOTE:
If a Protection Dummy Connector is attached to the AC Power Supply
Connector on the host machine side, remove the Dummy Connector before
connecting the AC Harness Connector from the Cassette Pedestal.
(The removed Dummy Connector will not be used.)
F-1-18
F-1-17

8
8
9) Connect the 3 connectors to the host machine and put the cables through the guides.
CAUTION:
Be sure to tuck the extra slack of the harness to the host machine side to prevent the
cables from being trapped.
[imageRUNNER ADVANCE C2030/2025/C2020 Series]
x3
x3
[Models other than imageRUNNER ADVANCE C2030/C2020 Series]
x3
x3
F-1-19
F-1-20
10) Loosen the screw on the Connector Cover included in the package, and install the
grounding wire between it and the toothed washer.
Screw
U Shape Terminal
Toothed Washer
CAUTION:
• Be sure to pay attention to the orientation of the Grounding Wire.
• Be sure to connect the wire from the direction of the arrow marked on the plate.
F-1-22
F-1-21

9
9
11) Install the Connector Cover.
• 1 W Sems Screw (Use the screw removed in step 8.)
12) Secure the equipment in place with the 4 adjusters.
NOTE:
Securing of the adjuster is not earthquake resistant.
F-1-23
F-1-24
NOTE:
• When installing the host machine at the same time, be sure to follow "Unpacking and
Installation" in the Installation Procedure Manual.
• When installing this equipment later, be sure to follow the following procedure.
13) Connect the power plug of the host machine to the outlet.
14) Turn ON the main power.
Setting the Cassette
1) Press the Cassette Release button, and pull out the Cassette 3.
Button
F-1-25

10
10
2) Hold the lever of the Side Guide Plate, and adjust the plate to the specied size. At this
time, move the Side Guide Plate by referring to the Size Index (Label) of the sheet size to
be set, and adjust the Side Guide Plate to the click position (position where it clicks).
3) Hold the lever of the Trailing Edge Guide Plate, and adjust it to the specied size. At this
time, move the Trailing Edge Guide Plate by referring to the Size Index (Label) of the sheet
size to be set, and adjust the Trailing Edge Guide Plate to the click position (position where
it clicks).
Side Guide Plate Lever
Side Guide Plate
Trail Edge Guide Plate
Trail Edge Guide Plate Lever
4) Place papers.
5) Open the cover at insertion area of the Size Plate.
Paper
Cover
F-1-26
F-1-27
6) Cut the 2 places of the Size Plates with nippers.
Cut
7) Set the Size Plate according to the size being set. (Lump the Size Plates not in use
together and store them at the rear.)
8) Close the cover at insertion area of the Size Plate, and insert the cassette.
9) Set the Cassette 4 in the same way.
NOTE:
The paper size settings are recognized automatically.
F-1-28
F-1-29

11
11
Adjustment
[imageRUNNER ADVANCE C2030/C2020 Series]
NOTE:
The 2nd side of 2-sided print mentioned later means 2nd side in the image formation
order.
With this machine, 2nd side in the image formation order at duplex copy/print is
equivalent to the 1st side of the original.
Margin Adjustment (1st side)
1) Print from the Cassette 3 and 4, and check that the left edge margin is within 2.5 +/- 1.5mm.
Feed direction
of paper
L1
image
<In Case of Out of Range>
NOTE:
Adjustment method is the same for the Cassette 3 and 4.
2) Pull out the cassette.
F-1-30
3) Hold the lever of the Trailing Edge Guide Plate, and check the values of the scale on the 2
Adjustment Plates of the Trailing Edge Guide Plate.
4) Loosen the 3 Fixation Screws.
F-1-31
F-1-32