Canon Pixma iP110 series User manual

1
Canon iP110 Series Printer
Turning on the printer
1. Open the rear tray cover.
The paper output slot cover opens automatically.
2. Press the ON button to turn on the printer.
The POWER lamp flashes and then remains lit.
Note
• It may take a while for the printer to start printing immediately after you turn on the printer.
•
If the Alarm lamp flashes, see If an Error Occurs.

2
Turning off the printer
1. Press the ON button to turn off the printer.
When the POWER lamp stops flashing, the printer is turned off.
Important
Note
Carrying the Printer
Exercise sufficient care when carrying the printer.
When you remove the power cord, carry the printer, or stand it up, check that the POWER lamp is off.
Important
Note
•
When you unplug the power cord after turning off the printer, be sure to confirm that
the
POWER lamp is off.
•
If you stand the printer up or carry the printer before the POWER lamp goes off, this
may cause the ink to leak or the printer to break.
•
•
• If you repeatedly remove the power cord, carry the printer, or stand it up while the POWER lamp is on
or flashing, this may cause the ink to leak or the printer to break. (The same problem is caused even if
you use the optional portable kit.) For details on turning off the printer, see Turning off the printer.
• When carrying the printer, be careful not to shock the printer, to subject it to strong vibrations, to place
it
in the heat, or to put a heavy thing on it. This causes the printer to break or the ink to leak.
• Pack the printer carefully when carrying.
• X-ray and any other baggage inspection devices have no adverse effect on this printer.

3
Printer Components
Front View
(1) print head cover
Open to replace an ink tank or remove jammed paper inside the printer.
(2) paper guide
Align with the left side of the paper stack.
(3) paper support
Pull out fully to support paper loaded on the rear tray.
(4) rear tray cover
Open to load paper in the rear tray.
(5) rear tray
Load paper here. Two or more sheets of the same size and type of paper can be loaded at the same time
and fed automatically one sheet at a time.
(6) paper output slot
cover
Printed paper is ejected.
(7) paper thickness lever
Switches the clearance between the print head and the loaded paper to match the media type. Set to the left
when printing on envelopes. Set to the right when printing on paper other than envelopes.

4
*
All lamps are shown lit in the above figure for explanatory purposes .
(8) ON button – Turns the power on or off
(9) POWER lamp – Lights after flashing when the power is turned on
(10) RESUME/CANCEL button
-
Cancels a print job in progress. Holding this button down
lets you select maintenance options or printer settings.
(11) ALARM LAMP - Lights or flashes when an error occurs. When performing printer
maintenance or printer settings, options can be selected according to the number of
flashes. See Printer Troubleshooting p. 6-7.
(12) Wi-Fi button - Hold down to automatically set up the wireless LAN connection.
(13) Wi-Fi lamp - Lights or flashes to indicate the wireless LAN status.

5
Side View
(1)
AC adapter connector
Plug in the supplied universal AC adapter plug here.
(2)
USB port
Plug in the USB cable to connect the printer with a computer.
>
Important
• Do not touch the metal casing.
• Do not plug in or unplug the USB cable while printing.
Inside View
(1)
ink lamps
Lights or flashes to indicate the ink tank status.
(2)
print head holder
Install the print head here.
(3)
print head lock lever
Locks the print head into place.
See Replacing an ink tank p. 9

6
Printer Troubleshooting
You can check the status of the printer by the POWER and Alarm lamps.
 POWER lamp is off: The power is off.
 POWER lamp lights: The printer is ready to print.
 POWER lamp flashes: The printer is getting ready to print, or printing is in progress.
 Alarm lamp flashes: An error has occurred and the printer is not ready to print.
 POWER lamp flashes and Alarm lamp flashes alternately: An error that requires
contacting the service center may have occurred.
When an error occurs in printing, such as a paper jam or empty ink cartridge, the orange light
on the Alarm lamp will flash. The table on the next page will guide you through
troubleshooting some basic printer issues.
Figure 1
If, after taking appropriate action, the printer is still not working, contact your Case Manager
to forward a request for a new printer.
Please note that the printer may make noise when it is turned on. Allow a few minutes for it
to boot up and it should print quietly and without issues. If the noise persists or is
uncharacteristically loud, notify the Case Manager.

7
If an Error Occurs
When an error occurs in printing such as the printer is out of paper or paper is jammed, a troubleshooting
message is displayed automatically. Take the appropriate action described in the message.
When an error occurs, the Alarm lamp flashes and a Support Code (error number) is displayed on the
computer screen. For some errors, the POWER lamp and the Alarm lamp flashes alternately. Check the
status of the lamps and the message, then take the appropriate action to resolve the error.
Support Code Corresponding to the Number of Flashes of the Alarm Lamp
Example of 2 times flashing:
(A) Flashes (B) Goes off
Number of flashes Cause Support Code
2 flashes These is no paper in the rear tray. 1000
The paper size in the print settings and the size of the loaded paper do not
match. 2100, 2101
3 flashes Paper is jammed in the paper output slot or in the rear tray. 1300
4 flashes If the lamp on the ink tank is flashing, ink may have run out. 1600
The ink tank is not installed. 1660
The print head lock lever is not locked or an ink thank is installed
improperly. 1687
5 flashes The print head may be damaged. 1401, 1403, 1405
7 flashes
More than one ink tank of the same color is installed (the lamp on the ink
tank flashes.). 1681
8 flashes The ink absorber is almost full. 1700, 1701
11 flashes Automatic Print Head Alignment failed. 2500
Cannot perform printing with the current ink setting. 4103
12 flashes Battery has exhausted. 1810
15 flashes The ink tank cannot be recognized. 1410, 1411
17 flashes The ink has run out. (The lamp on the ink tank flashes.) 1688
18 flashes The remaining ink level cannot be correctly detected. 1689
21 flashes The printer cannot detect the paper size. 2103

8
Support Code Corresponding to the Number of Alternate Flashes of the POWER Lamp
and the Alarm Lamp
Example of 2 times flashing:
(A) Flashes
(B) Goes off
Number of flashes Cause Support Code
2 flashes Printer error has occurred. 5100
7 flashes Printer error has occurred.

9
Replacing an Ink Tank
When remaining ink cautions or errors occur, the Alarm lamp will flash to inform you of the
error. Count the number of flashes and take appropriate action. When you need to replace an
ink tank, follow the steps below.
1. Make sure that the power is turned on.
2. Open the print head cover.
3. Remove the ink tank with the lamp flashing fast. (Do not touch other parts besides the
ink tanks). Push the tab and lift the ink to remove.
4. Do not remove both ink tanks at the same time. Be sure to replace ink tanks one by one
when replacing both ink tanks.
5. Remove the new ink from its packaging, then remove the protective cap from the
bottom of the ink tank.
6. Insert the front end of the ink tank into the print head at a slant.
7. Press the ink tank until it snaps firmly into place. You should hear a click ensuring that it
has been secured.
8. Make sure that the ink lamp lights up.
9. Close the print head cover
For other hardware or system-related issues, contact your Case Manager as
soon as possible.