Car Solutions QPI-AUDI-CMD-V2.0 User manual

www.car-solutions.com

Warning
When installing the main unit, do not remove or alter existing
vehicle fasteners, including nuts, bolts, screw, clips, and fittings.
Never detach, move or alter existing vehicle wiring, including
electrical grounds and straps. Alteration of existing vehicle
components may make vehicle unsafe to operate. Should be
no any electronic devices or magnetic pole around installation
place.
Air bags are vital part of a safety system. Never install main unit
in a way which will alter air bag wiring or interfere with air bag
deployment. Air bags must function properly in the event of an
accident.
Before installing, check the location of pipe, tank, electrical
cables and others.
Read and follow the instruction manual.
Wiring location must not interfere driving, get in or out from car.
Use electrical tape to insulate the ends of all wires, even if they
are not used. Proper insulation prevents arcs, shocks and fires.
When installation is complete, test all vehicle electrical systems
to ensure they operate correctly, including lights, horn, brake
lights, and emergency flashers.
According to our sales policy, any problems caused by user’s
mistake, careless can not be guaranteed.
Caution
All steps of installation should be done by well-trained specialist.
During installation ignition key should be taken off and after all
installation finish connect power cable with interface for the last
step.
Do not install the main unit in places where it ma be exposed to
dew condensation (around the air conditioning hose, etc), or in
locations where it may come in contact with water, high levels of
moisture, dust or oily smoke
Install wiring in a manner in which cables will not come in contact
with metal parts. The wiring may be damaged by contact with
metal parts, resulting in fire and shocks. Avoid all contact with hot
surfaces when wiring the main unit. High temperatures may
damage wiring, causing shorts, arcing and fires.
Kindly check all parts are in the box, when receiving the product, if
anything missing, inform to the supplier or manufacturer.
Warning / Caution
2
www.car-solutions.com
www.car-solutions.com

Table of Contents
1. Specifications
1.1 Main Specifications
1.2 Features
1.3 System Diagram
1.4 Components
1.5 Exterior
2. Installation
2.1 Installation Diagram
2.2 Installation
3. Settings
3.1 DIP Switch
3.2 Remote Control
3.3 Factory Menu
3.3.1 Image, Park
3.3.2 UTIL1
3.3.3 UTIL2
3.4 Original Button Usage
3.5 OSD
4. Trouble Shooting
4
5
6
7
9
10
11
12
13
14
16
18
22
23
25
3
www.car-solutions.com
www.car-solutions.com

1. Specifications
1.1 Main Specifications
1. Car Compatibility
AUDI Cars in combination with MMI 3G, 3G+
2. Components
Interface* 1EA
3. MULTIMEDIA INTERFACE input specification
3 * A/V input (video external input)
1 * CVBS(Rear Camera) input
1 * Analog RGB input (Navigation system output)
1 * LCD input (Car system input)
4. MULTIMEDIA INTERFACE output specification
1 * LCD output
5. Power specification
Input power : 8VDC ~ 18VDC
Consumed power : 5WATT
6. Switch input mode
- External display skip function : through DIP switch, can
control each video input
- Through remote control, can change input mode
- Through CAN or rear lamp cable, rear camera can be
detected
4
www.car-solutions.com
www.car-solutions.com

1. Specifications
Easy installation through connection with command
Able to control NAVI, DVD, DTV function by using I-Drive
Controller
Able to adjust DVD, NAVI display on screen
Improved Screen Display (user-oriented interface)
Mode change through original button
Provide power cable to connect with rear camera
Dynamic PAS(Parking assistance system)+PDC,
moving parking line according movement of steering wheel
1.2 Features
5
www.car-solutions.com
www.car-solutions.com

1. Specifications
1.3 System Diagram
DISPLAY
A/V 1
NAVIGATION Input
(Analog RGB)
CVBS
(Rear camera)
Car Screen Input
(CAR MAIN BOARD)
A/V 2
A/V 3 VIDEO
CIRCUIT
VIDEO MUX
MCU
Power Input
(+8VDC ~ +18VDC)
POWER
CIRCUIT
Dip S/W
A/V OUT HEADREST
MONITOR
Remote control Switch for source toggle OEM Button (Can Signal)
Car Installation
OEM LCD
Rear Camera Power
(+9VDC)
6
www.car-solutions.com
www.car-solutions.com

1. Specifications
1.4 Components
A/V cable * 1EA
Mode cable * 1EA
IR cable * 1EA R-CAM POWER cable * 1EA
POWER cable (10P) * 1EA
(HPOWER0044)
(HARETC0002)
(HAVCAB0002)
Remote control * 1ea
(REMOTE0001)
(HARETC0001)
(HIRCAB0002)
TOUCH OUT cable * 1ea
(HTOUCH0004)
TOUCH IN cable * 1ea
(HTOUCH0009) RGB cable * 1ea
(HRGBCA0013)
LCD cable * 1ea
(HLCDCA0015)
7
www.car-solutions.com
www.car-solutions.com

7” Touch Panel
(TOULCD0013)
8” Touch Panel
(TOUPAN0004)
1. Specifications
1.4 Components
8
www.car-solutions.com
OPTIONAL
www.car-solutions.com

1. Specifications
1.5 Exterior
Dimension
Width 160mm
Length 97.5mm
Height 21.1mm
①⑤⑥⑦
⑧⑨⑩⑪⑫
②③④
⑬
①REMOTE
②POWER
③TO NAVI
④T/S-IN FROM LCD
⑤R-CAM
⑥RGB-IN
⑦AV IN/OUT
⑧MODE
⑨LCD-OUT
⑪TEST
⑩LVDS-IN
⑫LED
⑬DIP S/W
9
www.car-solutions.com
www.car-solutions.com

2. Installation
2.1 Installation Diagram
Original
Monitor
Provided LCD Cable
Original LCD Cable
REAR (12V OUT)
GND
AV1
AV2
AV3
REAR C
Audio L
Audio R
AV/OUT Video
Navigation
Touch Screen
Provided TOUCH IN
Cable
B DATA (blue) SYNC
GND
IR-DTV
NAVI-VS
IR-NAVI
IR-DVD
R DATA (red) G DATA (green)
CAN Low
CAN High
ACC
REAR
MMI
GND
CAN-H-HS
CAN-L-HS
F-CAM-DET
SAFE
CAN-H-LS
CAN-L-LS
Command
Connecting CAN wire
※ In case of 3G+ Vehicles(A6, A7, A8)
Connect CAN-H-HS(Brown+Green-3Pin) of the interface to CAN High(Orange+Brown) of the car
Connect CAN-L-HS(Green-4pin)of the interface to CAN Low(Orange+Brown)of the car
※ In case of 3G Vehicles(Q3, Q5, Q7, A4, S4)
Connect CAN-H-LS(Brown+Green-9Pin) of the interface to CAN High(Orange+Green) of the car
Connect CAN-L-LS(Green-10Pin) of the interface to CAN High(Orange+Brown) of the car
10
www.car-solutions.com
www.car-solutions.com

2. Installation
2.2 Installation
①Here are pictures of the rear
view of the disassembled
monitor and command.
You can see that original
LCD cable of monitor is
connected to the
command in the picture
above.
②Connect the original LCD cable
to “LCD-OUT” of the Interface
after disconnecting it from the
command.
And connect the LCD cable
enclosed in our package to
“LVDS-IN” of the Interface.
Then connect the opposite end
of the cable to the spot that the
original LCD cable is connected
of command
Rear view of command
Rear view of monitor Provided LCD Cable
Original LCD Cable
11
www.car-solutions.com
www.car-solutions.com

3. Settings
3.1 DIP Switch
PIN Function Dip S/W Selection
1 Displaying RGB input ON : RGB mode skip
OFF : RGB mode display
2 Displaying A/V 1 ON : A/V 1 mode skip
OFF : A/V1 mode display
3 Displaying A/V 2 ON : A/V 2 mode skip
OFF : A/V2 mode display
4 Displaying A/V 3 ON : A/V 3 mode skip
OFF : A/V3 mode display
5 Setup for
Resolution of monitor ON : Low resolution
OFF : High resolution
6 N.C
7 Setup of rear camera use ON : CVBS4
OFF : MAIN
8 Reset factory settings
(not use for user)
ON : Product factory reset
OFF : DEFAULT
※Example DIP S/W usage
- Use input mode : A/V2, A/V3
- Use original navigation
- External rear camera
▷DIP S/W : 1,2 ON (hide INPUT MODE)
▷DIP S/W : 3 OFF (A/V2 display)
▷DIP S/W : 4 OFF (A/V3 display)
▷DIP S/W : 5 OFF (High Resolution)
▷DIP S/W : 6 OFF (Standard GUI model)
▷DIP S/W : 7 ON (display external rear cam)
▷DIP S/W : 8 OFF
※ON : DOWN / OFF : UP
Default : #8 OFF
12
※Please make sure to disconnect the power cable of the interface and reconnect
the power cable again to apply the dip switch setting whenever changing DIP switch.
Otherwise, DIP switch setting will not be applied.
www.car-solutions.com
www.car-solutions.com

3. Settings
3.2 Remote Control
Key Function
POWER & PIP Unavailable
MENU Activating OSD menu
OK Making a selection, changing image display
▲Moving upward
▼Moving downward
◀Moving leftward
(If you press this button 2 seconds long, you can access the factory
mode.)
▶Moving rightward (If you press this button 2 seconds long, you can reset all the
data about user environment.)
13
www.car-solutions.com
www.car-solutions.com

3. Settings
3.3.1 FACTORY MODE-IMAGE, PARK
IMAGE
Adjust navigation position and size
H-POSITION : Move display horizontally
V-POSITION : Move display vertically
FACTORY mode – Press ◀button 2 seconds long on the remote control.
PARK
PAS TYPE : Selecting Type of parking guide line
- NOT USED : Not use Parking guide line
- PAS ON : Selecting Dynamic Parking guide line
- PAS OFF : Selecting fixed Parking guide line
PAS SETUP : Adjusting the position and Selecting
type of the parking guide line
REAR TYPE : Choose rear camera recognition
* LAMP - Detecting the rear view camera via
rear lamp (Installer must connect “Rear-C”
cable of the power cable to the rear lamp
of the car.)
*CAN - Detecting the rear view camera by
CAN signal (Installer must connect “CAN”
cable of the power cable to the “CAN”
cable of the car.)
SAFE ENABLE : If your car is connected with CAN
cable and it is in ”ON” state, you
can NOT watch DVD or A/V
except original image or
navigation while driving. At that
time the screen get back to the
main (default : OFF)
RADAR ENABLE : When set the gear to “R”, Display
PDC
14
www.car-solutions.com
www.car-solutions.com

3. Settings
3.3.1 FACTORY MODE-IMAGE, PARK
In H-POSITION, use ◁, ▷on remote control, to adjust
parking guideline left and right.
PAS SETUP
Go to Factory Menu, choose PAS SETUP, by using OK button change
H-POS → V-POS → TYPE
In V-POSITION, use △, ▽on remote control, to adjust
parking guideline up and down.
TYPE
In TYPE, use △, ▽on remote control, to select parking
guide line Type for rear camera.
(0001 : wide parking guide line
0000 : narrow parking guide line
H-POS
V-POS
15
www.car-solutions.com
www.car-solutions.com

3. Settings
3.3.2 FACTORY MODE-UTIL1
FACTORY mode – Press ◀button 2 seconds long on the remote control.
UTIL1 – NAVI MODEL
Definition of the navigation
resolution
DEFAULT : default, 400X234, in low
resolution
KD-900(WVGA) : 800x480 in high
resolution, for Chinese
LS-901(WQVGA) : 800x480 in high
resolution, for Chinese, Taiwan
WP9200(WVGA) : 800x480 in high
resolution, for Israel
GI-8000N 3D(WVGA) : 800x480 in high
resolution, for Korea
GI-5000A(WVGA) : 800x480 in high
resolution, for Korea
I-ONE(WVGA) : 800x480 in high
resolution, for Korea
PAPAGO(WQVGA) : 480x234 in low
resolution, for Taiwan
HDMI (when SMI installed): 800x480 in
high resolution
* Go into FACTORY/ IMAGE (as
shown right) and adjust the
position and the size of the
navigation after setting the
definition of the navigation
Setup for navigation
UTIL1 - CAR MODEL
Selecting model of the car
AUDI S4
AUDI A4
AUDI A6
AUDI A7
AUDI A8
AUDI Q3
AUDI Q5
AUDI Q7
* Set pin#5 of DIP switch to the
right size of the monitor after
selecting model of the car.
(Refer to page9.)
Setup for car model
16
www.car-solutions.com
www.car-solutions.com

3. Settings
3.3.2 FACTORY MODE-UTIL1
FACTORY mode – Press ◀button 2 seconds long on the remote control.
UTIL1 – AVOUT SELECT
Selecting background sound
After
returning navigation or original
mode
DEFAULT : Selecting AV sound
just before changing
navigation or original mode
from the AV mode
AV 1~3 : Sound of the selected
AV source 1~3
UTIL1 - FACTORY RESET
FACTORY MODE RESET
17
www.car-solutions.com
www.car-solutions.com

3. Settings
3.3.3 FACTORY MODE-UTIL2
FACTORY mode – Press ◀button 2 seconds long on the remote control.
UTIL2 - I_DRV CONTROL
Selecting whether to use I_DRV
function or not
ON / OFF
A/V1 : Control DVD Remote control UI
A/V2 : Control DTV Remote control UI
UTIL2 - I_DRV REMOTE
Choose DTV and DVD model
to be control I_DRV function
LI-1DISC
NEC-6DISC
USER(when using IR MEMORY)
•Select DVD model: Setting on
AV1 Mode
•Select DTV model : Setting on
A/V2 mode
UTIL2 – IR MEMORY
To register DVD, DTV remote control, the
remote control value must be registered
and can be control with I-Drive
DVD(A/V1), DTV(A/V2)
※To use this function, in UTIL2-I_DRV
REMOTE select USER mode
DVD / DTV
UTIL2 – CALIBRATE
Touch Calibration
YES / NO
18
www.car-solutions.com
www.car-solutions.com

3. Settings
3.3.3 FACTORY MODE-UTIL2
①First of all, press ◀button on
remote controller 2 seconds
long or press
UP→DOWN→UP→MENU button
in order to access Factory
mode. Choose IR MEMORY on
UTIL2.
In IR MEMORY, you can choose
AV source of DTV and DVD you
want to use.
②Picture above shows DVD
remote control button value
input, select menu you want
to save. (To register DVD
remote control button value,
select IR MEMORY – DTV and
follow below instructions.
Example)
a. After select OK button on
OSD menu, press intended I-
Drive button
b. Indicated part above will
flicker, and press POWER on
DVD remote control.
(continue to next page)
FACTORY mode – Press ◀button 2 seconds long on the remote control.
What is IR-MEMORY Mode?
Is to allow MMI and touch screen to control other DVD or DTV (besides
the existing,; for example : SANYO, NECVOX) by register remote
control value.
UTIL2 – IR MEMORY
19
www.car-solutions.com
www.car-solutions.com

3. Settings
3.3.3 FACTORY MODE-UTIL2
③After register, select “SRC” button
in OSD menu. Then you can see
confirmation window as shown
above. At the moment,
(If data is saved, DVD TYPE and
DTV TYPE will be changed to “USER”
automatically.)
If you see “SUCCESS” on screen, the
data is saved clearly and you can
control DVD via touch screen. BUT,
you MUST change the option in
FACTORY-UTIL2-I_DRV REMOTE to
“USER”.
※ When touch the middle of the screen, you can control DVD, DTV using
remote control UI via touch screen or MMI
※ If touch the screen in DVD(A/V1), DTV(A/V2) mode, Can see remote control UI
If touch the screen in RGB, A/V3 mode, Can see mode switching UI
- If you want to see mode switching UI in DVD, DTV mode, Select “SRC” button
FACTORY mode – Press ◀button 2 seconds long on the remote control.
UTIL2 – IR MEMORY
Instruction> continued…
c. The values that you
registered will appear as green
text in the marked area on
pressing the button. And the
values will be saved
automatically.
d. Register remain buttons’
value in OSD menu like the
above-mentioned.
20
www.car-solutions.com
www.car-solutions.com