Caraudio-Systems MD-VW03 User manual

Page 1
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
MD-VW03

Page 2
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
Contents:
Contents...................................................................................................................................... 2
Safety Instructions...................................................................................................................... 3
Service / Support........................................................................................................................ 4
Shipment..................................................................................................................................... 4
Product Description.................................................................................................................... 5
Installation of the harness MD-VW03 in Golf 5, Touran, Passat ...........................................5-7
Installation of the harness MD-VW03 in VW Touareg and T5..............................................8-9
Function and control............................................................................................................10-11

Page 3
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
Safety Instructions:
1. Read through mounting guidelines:
Please read through all safety instructions and handling directions intently before installation
and start up of the device.
2. Keep mounting guidelines:
Keep the instruction manual and safety instructions for potential further reference.
3. Caution advises:
Please follow all caution advises contained in the mounting guidelines.
4. Water and humidity:
The device should not be operated near water or near a humidity source.
5. Warmness / heat:
The device should not be set up in direct proximity of heat sources (e. g. power amplifier).
6. Connection / electric power supply:
Use the device only at a +12 volt vehicle electrical system. Make sure to have a proper
ground.
7. Intrusion of objects or liquids:
Please make sure that no objects or liquids can intrude the interior of the device! (Danger of
short circuit!)
8. Repairs:
You should call on qualified personnel, if:
a plug or a connector have been damaged
cables are damaged
objects have fallen into the device or liquids have intruded it
the product has been exposed to humidity
the device doesn't function normally or if
significant changes in the operating performance can be observed
the product/casing has been damaged.
9. Operation:
Start no operation that is likely to distract you for a prolonged time from road traffic or traffic
related events –RISK OF ACCIDENT!!!
10. Warranty:
The warranty will cease in case that:
you open the device or the casing
you carry out repairs single handed
you use the device improperly
the device shows damages caused by external forces or mischievous destructions.
We assume no liability for damages to the vehicle or to people.

Page 4
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
Service & Support:
All our products are manufactured under strict quality control. Each device is being tested be-
fore shipment. If nevertheless do occur problems or if you have technical questions, contact
us directly under:
Caraudio Systems Vertriebs GmbH
Rheinhorststr. 22
67071 Ludwigshafen am Rhein
Germany
Phone: [phone]
Fax: [phone]
In addition to constant product update and development related changes the instruction manu-
als of the devices are constantly edited and kept up to date.
To enable us to provide you with the right information and support for the device you have
got at hand please add the following information to every inquiry:
Date of purchase, your name and address, item number and the type of your vehicle.
Shipment:
Harness MD-VW03
Manual
iPod® ist ein eingetragenes Markenzeichen der Apple Computer, Inc.
iPod® is a registered trademark of Apple Computer, Inc.

Page 5
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
Product Description:
Article: MD-VW03
Features: Harness for Multimedia interface “MULTI200”
For use with the following navigation systems:
VW with MFD3 / RNS510:
Golf5, Passat, Touran
Touareg, T5
Pin assignment of the harness:
Color/connector:
Signal:
26pin AMP connector:
To the MFD3 / RNS510
18pin AMP connector:
To the interface MULTI200
● Red:
+12V DC (Battery)
● Black:
Ground
● Yellow:
CAN-HIGH
● Blue:
CAN-LOW
● Pink:
Ignition +12V (output, max. 500mA)
● Green:
Power supply rear view camera +12V (max. 1A)
(1) 3 Pin AMP female connector:
Remote control device 1
(2) 3 Pin AMP female connector:
Remote control device 2
Installation of the harness with MULTI200:
Instructions for VW Golf 5, Touran, Passat:
Please remember to switch off the ignition prior to installing this interface.
1. The decorative moulding is mounted with 8 clips.
Remove the navigation system carfully. Use a dedicated
tool to do so.
Remove the 4 TORX screws as shown on the right and
remove the navigation system from the dash.

Page 6
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
2. Remove the Quadlock plug form the navigation system.
Connect the 26pin AMP connector from the harness
to the navigation.
3. Connect the blue cable from the harness to pin 10 (CAN LOW)
at the Quadlock plug and the yellow cable to
pin 9 (CAN HIGH).
The black cable has to be connected to ground on pin 12.
The red cable has to be connected to battery on pin 15.
Additionally you can use the pink cable (+12V) to switch
on the video sources.
4. Connect the according remote control cables to the
3pin AMP connectors (eg. „STA-AL25“ for Alpine DVD
devices). You can use additional Y-harnesses
„CABLE-415“ / „CABLE-416“ (sold separately) to
connect the infrared receivers of the video devices
in parallel to the interface.
5. Connect the Video / Audio rca cables (not included)
to the plugs (AV1 / AV2) at the interface
and the video sources.
6. Connect the 14pin Molex connector and
the 18pin AMP connector to the interface.
You can also connect an external monitor to the
"VIDEO OUT" plug at the interface.
Remote con-
trol AV2
Remote con-
trol AV1

Page 7
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
6. To use the rear view camera function you have
to open the interface.
As seen on the right side you have to close the
connection with the middle jumper.
Connect the video signal of the aftermarket rear view
camera to the "R-CAM IN" plug.
The green cable of the harness can be used to supply
power (+12V) to the rear view camera.
7. Reconnect all original connectors and reassemble the system back into the car.
To enable the automatic activation of the rear view camera image eg. from radio
mode, the MFD3 / RNS510 System has to coded to use the rear view camera.
The coding can be done with the OEM VW diagnosis.
Rear view camera
function - On

Page 8
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
Instructions for VW Touareg and T5:
Please remember to switch off the ignition prior to installing this interface.
1. Loosen the navigation system from its mounting points
and remove it from the dash.
You will need a dedicated tool which isn’t supplied.
2. Remove the Quadlock plug form the navigation system.
Connect the 26pin AMP connector from the harness
to the navigation.
3. Connect the blue cable from the harness to pin 10 (CAN LOW)
at the Quadlock plug and the yellow cable to
pin 9 (CAN HIGH).
The black cable has to be connected to ground on pin 12.
The red cable has to be connected to battery on pin 15.
Additionally you can use the pink cable (+12V) to switch
on the video sources.
4. Connect the according remote control cables to the
3pin AMP connectors (eg. „STA-AL25“ for Alpine DVD
devices). You can use additional Y-harnesses
„CABLE-415“ / „CABLE-416“ (sold separately) to
connect the infrared receivers of the video devices
in parallel to the interface.
Remote con-
trol AV1
Remote con-
trol AV2

Page 9
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
5. Connect the Video / Audio RCA cables (not included)
to the plugs (AV1 / AV2) at the interface
and the video sources.
6. Connect the 14pin Molex connector and
the 18pin AMP connector to the interface.
You can also connect an external monitor to the
"VIDEO OUT" plug at the interface.
6. To use the rear view camera function you have
to open the interface.
As seen on the right side you have to close the
connection with the middle jumper.
Connect the video signal of the aftermarket rear view
camera to the "R-CAM IN" plug.
The green cable of the harness can be used to supply
power (+12V) to the rear view camera.
7. Reconnect all original connectors and reassemble the system back into the car.
To enable the automatic activation of the rear view camera image eg. in radio
mode, the MFD3 / RNS510 System has to coded to use the rear view camera.
The coding can be done with the OEM VW diagnosis.
Rear view camera
function - On

Page 10
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
Function and control:
Activation:
To activate the device control functions you have to press
„MEDIA“ on the left side and then „VIDEO“ on the
touch screen.
The MFD3 / RNS-510 is now in TV mode.
Device assignment:
Press „Extras“ and then „V-Text“.
Now press „Seite“ or “Page”.
Now you can enter the RC codes for you devices with the
numpad. The Codes always have three digits.
Eg. the first device > „101“, the second device > „203“.
By pressing „OK“ the RC code is saved.
Switch between the devices with the „station list“.
Devices RC Codes:
Model
RC Code:
DVD USB, MP410, MP412, AD212U, DVP-1000M, DVP-900HD
x01
DVBT2007, Dietz 1491/V
x02
AMPIRE DVB-T100
x03
DVB2008, TRT400
x04
DVDC CKO DVC10
x05
DVD-Changer CKO- DVC 6M , Yamakawa DVD-Changer
x06
DVBT NL, SENERGY, C-KO DVBT-1080, Axion DVBT 500
x07
DVD ADJQ-DVDRD, PYLE PLTD24, Veba,
Carmedien CM06
x08
DVD 1/2 DIN (NO NAME)
x09
DVD Alpine RUE - 4201
x10
DVD Alpine RUE - 4158;TUE-T150DV
x11
DVBT Eastern SE863-T
x12
iPod®Vlink
x13
DVBT ZENEC ZE-DVBT25, TRT500
x14
V-HUB VPA-B222R Alpine Radio
x15
V-HUB VPA-B222R Alpine DVD
x16
DVD Necvox DVA-3206
x17
Analog-TV Alpine TUE-T112P
x18
Analog-TV TRT-003
x19
BOA-DVD 85700 /AIV, C-KO 412
x20
DVD Visteon VXM2200
x21
DVBT Quantum QTM10
x22
DVD Elite ELT-900XU Novosonic
x23
DVDC CkO MPC6
x24
Model
RC Code:
DVD-TIXXON (No Name)
x25
HD-Player 3,5“ MVIX MV-5000U
x26
DVD Axion VDV-402
x27
DVD Bullit CDVD12
x28
DVD ZENEC ZE-080
x29
DVBT Ampire DVBT200
x30
DVBT&DVD USB Digitaldynamic Multiplayer
x31
iPod Alpine KCE-425I
x32
A-TV TVT-765
x33
DVBT Emperor DTR-1203
x34
DVBT Carmedien DVB423
x35
DVBT M-DTV-201-0
x36
DVDC Pioneer XDV-P6 (Reserviert)
x37
DVD Phonocar VM 015 (USB/SD)
x38
Hirschmann DVBT / Visteon DVBT
x39
HD Microlab - Pocket X Div 25 (2,5 Zoll HD P. Tixxon)
x40
DVB-T D80
x41
DAS / Dietz 1492 DVB-T
x42
DVBT Ampire DVBT50
x43

Page 11
C
Ca ar ra au ud di io o- -S Sy ys st te em ms s V Ve er rt tr ri ie eb bs s G Gm mb bH H
R
Rh he ei in nh ho or rs st ts st tr ra as ss se e 2 22 2
6
67 70 07 71 1 L Lu ud dw wi ig gs sh ha af fe en n
T
Te el l. .: : + [phone] 34 44 41 17 7- -0 0
F
Fa ax x. .: : + [phone] 34 44 41 17 7- -9 99 9
E
Em ma ai il l : : t te ec ch hn ni ik k@ @c ca ar ra au ud di io o- -s sy ys st te em ms s. .d de e
Control:
You can control the devices with the touch screen, the right knob and the arrow button at the
left upper corner of the monitor.
When you tap on the monitor two arrows
are displayed on the screen.
With them you can switch the channel (DVB-T)
or track (DVD).
You can also use the arrow buttons
at the left upper corner of the monitor.
In the “station list” you will find more control options
for your devices.
A new menu will pop up and show you the
available commands.
The commands on the left (left side of the slash)
are for DVB-T tuners, the ones on the right side
for DVD players.
To optimize the handling of the video source’s menu
first activate its menu of it.
Select (Menu / Setup) in the station list to do so.
Now select „Extras“ and „V-Text“ to invoke the
controls.
Pressing „Zoom“ on the screen sends the command OK
to the device. „Stop“ is step back.
Use the arrows on the screen and the right knob to
navigate in the menu.
Thank you for choosing our products and we are sure you will have a lot of joy with it!
© Caraudio-Systems 2009
Rev. 1.0 / 26.05.2009