Caraudio-Systems MD-VW01 User manual

Page1
MD-VW01

Page2
Contents:
Contents...................................................................................................................................... 2
Safety Instructions...................................................................................................................... 3
Service / Support........................................................................................................................ 4
Shipment..................................................................................................................................... 4
Product Description.................................................................................................................... 5
Installation of the harness with MULTI200............................................................................5-7
Function and control................................................................................................................8-9
Button assignment for MFD1 System........................................................................................ 9
Button assignment for AUDI Navi Plus System...................................................................... 10

Page3
Safety Instructions:
1. Read through mounting guidelines:
Please read through all safety instructions and handling directions intently before installation
and start up of the device.
2. Keep mounting guidelines:
Keep the instruction manual and safety instructions for potential further reference.
3. Caution advises:
Please follow all caution advises contained in the mounting guidelines.
4. Water and humidity:
The device should not be operated near water or near a humidity source.
5. Warmness / heat:
The device should not be set up in direct proximity of heat sources (e. g. power amplifier).
6. Connection / electric power supply:
Use the device only at a +12 volt vehicle electrical system. Make sure to have a proper
ground.
7. Intrusion of objects or liquids:
Please make sure that no objects or liquids can intrude the interior of the device! (Danger of
short circuit!)
8. Repairs:
You should call on qualified personnel, if:
a plug or a connector have been damaged
cables are damaged
objects have fallen into the device or liquids have intruded it
the product has been exposed to humidity
the device doesn't function normally or if
significant changes in the operating performance can be observed
the product/casing has been damaged.
9. Operation:
Start no operation that is likely to distract you for a prolonged time from road traffic or traffic
related events –RISK OF ACCIDENT!!!
10. Warranty:
The warranty will cease in case that:
you open the device or the casing
you carry out repairs single handed
you use the device improperly
the device shows damages caused by external forces or mischievous destructions.
We assume no liability for damages to the vehicle or to people.

Page4
Service & Support:
All our products are manufactured under strict quality control. Each device is being tested be-
fore shipment. If nevertheless do occur problems or if you have technical questions, contact
us directly under:
Caraudio-Systems Vertriebs GmbH
manufacturer/distribution
In den Fuchslöchern 3
D-67240 Bobenheim-Roxheim
email [email protected]
In addition to constant product update and development related changes the instruction manu-
als of the devices are constantly edited and kept up to date.
To enable us to provide you with the right information and support for the device you have
got at hand please add the following information to every inquiry:
Date of purchase, your name and address, item number and the type of your vehicle.
Shipment:
Harness MD-VW01
Manual
iPod® ist ein eingetragenes Markenzeichen der Apple Computer, Inc.
iPod® is a registered trademark of Apple Computer, Inc.

Page5
Product Description:
Article: MD-VW01
Features: Harness for Multimedia Interface “MULTI200”
For use with the following navigation systems:
VW and SKODA with MFD1:
Golf4, Bora, Passat, T4, Octavia I, Superb
AUDI with Navi Plus:
A2, A3, A4, A6, A8
Pin assignment of the harness:
Color/Connector:
Signal/Connection:
10pin connector:
To MFD I / NAVI Plus
18pin AMP connector:
To interface MULTI200
● Red:
+12V DC (Battery)
● Black:
Ground
● Yellow:
CAN-HIGH
● Blue:
CAN-LOW
● Pink:
Ignition +12V (output, max. 500mA)
● Green:
Power supply rear view camera +12V (max. 1A)
●White:
Reverse gear recognition (12V)
(1) 3 Pin AMP connector:
Remote control device 1
(2) 3 Pin AMP connector:
Remote control device 2
Installation of the harness with MULTI200:
Instructions for VW, Skoda with MFD1 and AUDI with Navi Plus:
Please remember to switch off the ignition prior to installing this interface.
1. Remove the navigation system from its mounting point
and pull it out gently from the dash.
Remove all its connectors.
MFD 1

Page6
2. Connect the 10pin plug of the harness to the navigation unit.
3. Connect the blue cable from the harness to pin 26 of the
26 pin connector of the navigation unit. Connect the yellow
cable to pin 13 of the 26 pin connector.
Connect the black cable to ground (power connector pin 8)
and the red cable to 12V battery (power connector pin 7).
Additionally you can use the pink cable (+12V) to switch
on the video sources.
4. Connect the according remote control cables to the
3pin AMP connectors (eg. „STA-AL25“ for Alpine DVD
devices). You can use additional Y-harnesses
„CABLE-415“ / „CABLE-416“ (sold separately) to
connect the infrared receivers of the video devices
in parallel to the interface.
5. Connect the Video / Audio rca cables (not included)
to the plugs (AV1 / AV2) at the interface
and the video sources.
6. Connect the 14pin Molex connector and
the 18pin AMP connector to the interface.
You can also connect an external monitor to the
"VIDEO OUT" plug at the interface.
Remote con-
trol AV1
Remote con-
trol AV2

Page7
7. To use the rear view camera function you have
to open the interface.
As seen on the right side you have to close the
connection with the middle jumper.
Connect the video signal of the aftermarket rear view
camera to the "R-CAM IN" plug.
The green cable of the harness can be used to supply
power (+12V) to the rear view camera.
8. Reconnect all original connectors and reassemble the system into the car.
Eine automatische Umschaltung des Rückfahrkamerabildes aus z.B. der Radio
Ebene ist mit manchen MFD1 / NAVI Plus System nicht möglich.
Rear view camera
function - On

Page8
Function and control:
Activation:
Pressing „Audio“ in a VW or Skoda respectively
“Radio/CD/TV“ in an Audi activates the TV/AV input.
Device assignment:
Due to the lack of a display connection to MDF1 and Navi+, the setup has to be done without
optical feedback.
Pressing the button „AS“ (MFD1) or „MODE“ (Navi+) for more than 3 seconds activates the
device assignment.
Turning the right knob clockwise sets up the device specific rc code.
When activated the first code is 01. (See below for details)
Pressing the right knob again activates the setup for the second device.
You can select the rc code like before.
When pressing the right knob again the settings are stored and the setup is left.
Devices RC codes:
Model
RC Code:
DVD USB, MP410, MP412, AD212U, DVP-1000M,
DVP-900HD
1
DVBT2007, Dietz 1491/V
2
AMPIRE DVB-T100
3
DVB2008, TRT400
4
DVDC CKO DVC10
5
DVD-Changer CKO- DVC 6M , YamakawaDVD-Changer
6
DVBT NL, SENERGY, C-KO DVBT-1080, Axion DVBT 500
7
DVD ADJQ-DVDRD, PYLE PLTD24, Veba,
Carmedien CM06
8
DVD 1/2 DIN (NO NAME)
9
DVD Alpine RUE –4201
10
DVD Alpine RUE - 4158;TUE-T150DV
11
DVBT Eastern SE863-T
12
iPod®Vlink
13
DVBT ZENEC ZE-DVBT25
14
V-HUB VPA-B222R Alpine Radio
15
V-HUB VPA-B222R Alpine DVD
16
DVD Necvox DVA-3206
17
Analog-TV Alpine TUE-T112P
18
Analog-TV TRT-003
19
BOA-DVD 85700 /AIV, C-KO 412
20
DVD Visteon VXM2200
21
DVBT Quantum QTM10
22
Model
RC Code:
DVD Elite ELT-900XU Novosonic
23
DVDC CkO MPC6
24
DVD-TIXXON (No Name)
25
HD-Player 3,5“ MVIX MV-5000U
26
DVD Axion VDV-402
27
DVD Bullit CDVD12
28
DVD ZENEC ZE-080
29
DVBT Ampire DVBT200
30
DVBT&DVD USB DigitaldynamicMultiplayer
31
iPod Alpine KCE-425I
32
A-TV TVT-765
33
Emperor Mini DVBT
34
DVBT Carmedien DVB423
35
DVBT M-DTV-201-0
36
DVDC Pioneer XDV-P6 (Reserviert)
37
DVD Phonocar VM 015 (USB/SD)
38
Hirschmann DVBT / Visteon DVBT
39
HD Microlab - Pocket X Div 25 (2,5 Zoll HD P. Tixxon)
40
DVB-T D80
41
DAS / Dietz 1492 DVB-T
42
DVBT Ampire DVBT50
43

Page9
Control:
The video sources can be controlled with the buttons at the navigation system.
You can switch between AV1 / AV2 by pressing the right turn knob more than 3 seconds.
See below for all buttons.
Button assignment for MFD I:
Button assignment part 1
Button assignment part 2
●─● MFD 1 ●─●
Modell
1
2
3
4
5
6
7
8
9
9 (3Sec)
DVD / DVDC
PLAY
PBC
TITLE
←
→
SETUP
TRACK-
TRACK+
AV
RC CODE
DVB-T TUNER
PLAY/PAUSE
EPG
INFO
←
→
MENU
CH-
CH+
AV
RC CODE
I-POD®CONTROL
PLAY/PAUSE
SHUFFLE
REP.
←
→
BULB
TRACK-
TRACK+
EJECT
RC CODE
ANALOG TUNER
SCAN
FM
DISP
CH-
CH+
ADJUST
CH-
CH+
MODE
RC CODE
●─● MFD 1 ●─●
Modell
10
10 (3Sec)
11
11 (3sec)
12
13
14
14 (3sec)
DVD / DVDC
ZOOM/DISC
POWER
ENTER
SWITCH AV1/AV2
↑
↓
STOP
SETTINGS MENU
DVB-T TUNER
SCAN
POWER
OK
SWITCH AV1/AV2
↑
↓
EXIT
SETTINGS MENU
I-POD®CONTROL
-----
POWER
ENTER
SWITCH AV1/AV2
↑
↓
PLAY
SETTINGS MENU
ANALOG TUNER
MODE
POWER
MODE
SWITCH AV1/AV2
VOL +
VOL -
MUTE
SETTINGS MENU

Page10
Button assignment for AUDI Navi Plus:
Button assignment part 1
Button assignment part 2
●─● AUDI Navi Plus ●─●
Modell
1
2
3
4
5
5 (3Sec)
6
6 (3Sec)
7
DVD / DVDC
TRACK-
TRACK+
←
→
AV
POWER
STOP
SETTINGS MENU
ENTER
DVB-T TUNER
CH -
CH +
←
→
AV
POWER
EXIT
SETTINGS MENU
OK
I-POD®V-LINK
TRACK-
TRACK+
←
→
AV
POWER
ESC
SETTINGS MENU
ENTER
ANALOG TUNER
CH -
CH +
CH -
CH +
MODE
POWER
MUTE
SETTINGS MENU
MODE
●─● AUDI Navi Plus ●─●
Modell
7 (3Sec)
8
9
10
10 (3Sec)
11
11 (3sec)
12
12 (3Sec)
DVD / DVDC
SWITCH DEVICE
↑
↓
SETUP
RC CODE
PBC
SUB
PLAY
TITLE / DISC
DVB-T TUNER
SWITCH DEVICE
↑
↓
MENU
RC CODE
EPG
LANG
SCAN
INFO
I-POD®V-LINK
SWITCH DEVICE
↑
↓
LIGHT
RC CODE
SHUFFLE
-----
PLAY/PAUSE
REPEAT
ANALOG TUNER
SWITCH DEVICE
VOL +
VOL -
ADJUST
RC CODE
FM
MUTE
SCAN
DISPLAY